DRV8301DCAR
Product Specifications
DRV8301DCAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8301DCAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8301DCAR: Three phase gate driver with two current shunt amplifiers and a 1.5 A buck in a 56 pin HTSSOP
DRV8301DCAR is a 6 V to 60 V three phase pre driver in the 56 pin DCA body that drives six external N channel MOSFETs at 1.7 A source and 2.3 A sink, carries two current shunt amplifiers with adjustable gain and offset, and includes a 1.5 A buck converter for the controller in a HTSSOP-56 body of 56 pins. The DRV8301 is the earlier generation of the three phase gate driver family and it remains the part specified in systems that need a buck regulator on the same die as the gate drive. It supports 6 PWM or 3 PWM input modes, a bootstrap gate driver with trickle charge for 100 percent duty cycle, programmable dead time and programmable overcurrent thresholds, and reports faults on two pins and through a SPI port. The buck converter delivers up to 1.5 A with an adjustable output and an adjustable switching frequency.
Order code and package
| Order code | DRV8301DCAR |
| Phases | 3, six external N channel MOSFETs |
| Operating voltage | 6 V to 60 V |
| Peak source current | 1.7 A |
| Peak sink current | 2.3 A |
| Current shunt amplifiers | 2, adjustable gain and offset |
| Integrated buck | 1.5 A, adjustable output |
| Interface | 6 PWM or 3 PWM inputs, SPI for settings and faults |
| Logic levels | 3.3 V and 5 V |
| Package | 56 pin HTSSOP, DCA body, 14 mm by 8.1 mm |
Electrical parameters that decide the application
| Average gate drive current | 30 mA per phase, enough for the specified switching range |
| Bootstrap architecture | trickle charge, 100 percent duty cycle supported |
| Current shunt offset range | up to 3 V, adjustable |
| Current shunt gain | adjustable through the SPI register |
| Dead time | programmable through the SPI register |
| Overcurrent protection | programmable, based on VDS sensing of the external devices |
| Fault reporting | nFAULT, nOCTW and the SPI registers |
| Protections | PVDD and GVDD undervoltage, GVDD overvoltage, overtemperature warning and shutdown |
| Internal handshake | 50 ns between high side and low side switching |
| Buck output | up to 1.5 A, adjustable voltage and frequency |
Points to check before this part goes on a BOM
Two and a half amps of sink current and 30 mA of average gate drive current describe two different things and a board has to satisfy both. The peak current sets the edge rate, so 2.3 A into a 100 nC gate is a 43 ns discharge to the plateau. The average current sets the thermal budget inside the package: 30 mA per phase at 15 V is 0.45 W per phase of gate drive power, and that power is dissipated in the driver, not in the external device. Three phases at 30 mA therefore put 1.35 W into a body whose thermal path is the exposed pad, which is why this package is 56 pins and 14 mm long rather than a small QFN.
VDS sensing overcurrent protection is the right approach for a drive that has to distinguish a short from a start up inrush, and it depends on a resistor value that is easy to get wrong. The threshold is compared against the voltage across the external device while it is on, so the protection trips on a current that is set by the on resistance of that device. The on resistance rises with temperature by about 40 percent from 25 C to 100 C, so a threshold set at the room temperature current trips at a lower current when the stage is hot. That is a safe direction for protection and an unsafe direction for a motor that needs full torque when hot.
The adjustable offset of up to 3 V is what makes the two shunt amplifiers usable for bidirectional current in a single supply system. With a 3.3 V converter and a 1.65 V offset, the output can swing either side of the mid rail; with the full 3 V offset the swing is asymmetric and the measurement range in one direction is much larger than the other. The offset comes from a register, so the value is a firmware setting rather than a component, which means a change of range does not need a board change and does mean that the setting has to be recorded with the firmware version.
The 1.5 A buck on the same die is a convenience that carries a thermal consequence. The buck's loss and the gate drive loss share one pad, so a system that pulls the full 1.5 A at a 5 V output while driving three phases at 20 kHz is dissipating in one 14 mm body. The buck switching frequency and the gate drive frequency are independent, which helps, because they can be set apart to avoid the beat that would otherwise appear on the current sense outputs as a low frequency ripple.
The 50 ns handshake between the high side and the low side is a fixed internal delay, and it is not the same as the programmable dead time. The handshake prevents both outputs from being on at once when the input changes state, and the dead time register adds to it. A board that sets the dead time to its minimum still has the 50 ns of handshake in the path, so the total blanking is never zero, and a very narrow commanded pulse can be swallowed by the combination at high frequency.
Six PWM inputs and three PWM inputs are two different ways of telling the same stage what to do, and the choice changes the behaviour under a fault. In six PWM mode the controller owns the complementary signals and the driver only level shifts them, so a controller that stops updating leaves the last state on the outputs. In three PWM mode the driver generates the complementary signal itself, with the dead time it has been programmed with. The second mode is easier to drive and the first gives the controller control over the dead time per edge, which matters when the turn off behaviour of the two devices in a leg differs.
A 56 pin HTSSOP with an exposed pad is a package that needs the pad soldered to a plane, and the thermal number in the document is quoted for that condition. The pad carries the ground return of the gate drive loops, so a pad with a poor connection shows up as ringing on the gate waveforms before it shows up as a temperature rise. The symptom of a marginal pad is a stage that works at low current and misbehaves at high current, which is often attributed to the external MOSFETs rather than to the return path under the driver.
Where this order code fits
This order code belongs on brushless DC and permanent magnet synchronous drives in CPAP machines, pumps, e bikes, power tools, robotics and industrial automation, where the controller supply and the gate drive share one package and one thermal path. It is also the part chosen where the two shunt amplifiers have to measure phase current with a bidirectional offset, because the offset is adjustable up to 3 V and set by the SPI register rather than by an external divider. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
What is the difference between this part and the newer DRV8323? The DRV8301 integrates a 1.5 A buck converter and two shunt amplifiers in a 56 pin package. The newer family moves to three shunt amplifiers in some variants, a charge pump instead of a bootstrap with trickle charge, and bodies down to 6 mm by 6 mm. The pinouts and the register maps differ, so the choice is a board level decision rather than a substitution.
Can the buck supply the whole controller? It delivers up to 1.5 A, which covers a motor control microcontroller, its memory and a small sensor load. The loss of the buck shares the thermal pad with the gate drive, so the full current is only available when the gate drive loss is modest. A board that needs 1.5 A continuously should check the combined dissipation rather than the buck rating alone.
How is the overcurrent threshold set? Through a SPI register that sets the VDS level compared against the external device while it conducts. The trip current therefore depends on the on resistance of that device and on its temperature, which rises by roughly 40 percent from room temperature to 100 C. The threshold should be set at the hot resistance, not the cold one.
Why does the current sense offset matter? It sets the zero current output level and therefore how much of the converter range is available in each direction. A 1.65 V offset on a 3.3 V converter gives a symmetric swing; a 3 V offset gives a wide range in one direction and a narrow one in the other, which suits a drive that only regenerates briefly.
SUPERB holds and sources this driver line against the exact order code, with the reel, date code and country of origin stated on the offer. When a stage has to move to a second part, the Pin to Pin Cross Reference page sets out the checks that separate a working substitute from one that fails on the bench.