Contact Us

ADAU1701JSTZ

Brand: Analog Devices
Analog Devices ADAU1701JSTZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADAU1701JSTZ — Analog & Mixed-Signal ICs | Superb Automation

ADAU1701JSTZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADAU1701JSTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADAU1701JSTZ: 28 and 56 bit audio DSP with two converters in and four out

The ADAU1701JSTZ is a complete single chip audio system in a 48-lead LQFP: a 28 and 56 bit digital signal processor running at 50 MIPS, two analog to digital converters with 100 dB of signal to noise, four digital to analog converters with 104 dB, and the control ports needed to run it without a host processor. Programs load from a serial EEPROM at power up, so a speaker that has no microcontroller can still carry equalisation, crossovers and dynamics processing.

Published values

ParameterValue
Processor28-bit data with a 56-bit accumulator, 50 MIPS
Analog inputs2 ADCs, 100 dB signal to noise, -83 dB total harmonic distortion plus noise
Analog outputs4 DACs, 104 dB signal to noise, -90 dB total harmonic distortion plus noise
Analog to analog dynamic range98.5 dB
Sample rateup to 192 kHz
Serial portsI2S, left justified, right justified and TDM
ControlI2C or 4-wire SPI, self boot from serial EEPROM
Auxiliary converter4-input multiplexer for analog control
Clockcrystal oscillator, or PLL from 64, 256, 384 or 512 times the sample rate
Regulatoron chip, for 3.3 V systems
Package48-lead LQFP

What 50 MIPS buys in a speaker

A biquad filter costs about five instructions per sample in this core, so at 48 kHz one biquad is roughly 100 kIPS and 50 MIPS is about five hundred biquads, which is far more than a two way speaker needs. The real limit is not the arithmetic but the parameter update rate and the memory for delay lines: a 10 ms delay at 48 kHz is 480 words per channel, and a stereo bass management block with a 2 m delay is a meaningful share of the internal memory.

The 56-bit accumulator is what makes a cascade of filters usable at low level. A 28-bit multiply with a 56-bit accumulator keeps the rounding error of each stage below the 24-bit output, so ten chained biquads do not build up the noise floor that the same chain would show in a 32-bit fixed point part.

Self boot decides the system architecture

A device that loads its program from an EEPROM at power up needs no host processor, no firmware and no boot time communication. That removes a microcontroller from the bill of materials and, more importantly, removes the failure mode where the host does not answer and the speaker comes up silent. The same device can be programmed over I2C or SPI in a model that has a host, so the choice is a product decision rather than a silicon decision.

The PLL accepts 64, 256, 384 or 512 times the sample rate, which covers the clocks that a USB audio interface, a Bluetooth module and a digital television output provide. A 12.288 MHz master clock at 48 kHz is 256 times, and the same crystal gives 192 kHz at 64 times, so one crystal serves every rate in the table.

Converters and the analog side

The converters give 100 dB in and 104 dB out, and the analog to analog figure of 98.5 dB is the one that matters because it includes both. That is about 16 effective bits, which is enough for a powered speaker and not enough for a mastering chain. A product that needs more has to use the serial ports and external converters, which the part supports without glue logic.

The on chip regulator lets the digital core run from a 3.3 V rail while the converters use their own supply, which keeps the digital switching noise out of the analog reference. The auxiliary converter with its four input multiplexer is there for a volume knob or a tone control, so a front panel does not need its own ADC.

Where a customer needs a second position on this part, one stop BOM sourcing is the starting point, OEM procurement sets out the checks a substitution has to pass, and vendor consolidation is the short lead time route we quote against.

Two questions buyers ask

Does the ADAU1701 need a microcontroller to run? No. It can boot from a serial EEPROM by itself and run a fixed program, which is the usual configuration in a powered speaker. A host is only needed when the processing has to change at run time.

Can it run at 192 kHz with the internal converters? The serial ports support 192 kHz and the converters run at the standard rates. A product that needs 192 kHz end to end should take the audio in and out through the serial ports rather than through the on chip converters.