ADA4528-2ARMZ
Product Specifications
ADA4528-2ARMZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADA4528-2ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADA4528-2ARMZ: two 2.5 microvolt zero drift channels in one MSOP
The ADA4528-2ARMZ is the dual ADA4528 in an 8-lead MSOP. Each channel publishes 2.5 microvolts of maximum offset and 0.015 microvolts per degree C of maximum drift, with 135 decibels of minimum CMRR, a 2.2 to 5.5 volt supply and a 4 megahertz unity gain crossover. Two chopper channels in one package is what a differential bridge front end needs, and the reason to take both from one package rather than two is that the two channels then sit at the same temperature.
Published values
| Parameter | Value |
|---|---|
| Channels | 2 |
| Package | 8-lead MSOP (RM-8), also offered in an 8-lead LFCSP |
| Offset voltage | 2.5 uV maximum, per channel |
| Offset voltage drift | 0.015 uV/C maximum, per channel |
| Voltage noise density | 5.6 nV/root Hz at 1 kHz, gain 100 |
| Voltage noise, 0.1 Hz to 10 Hz | 97 nV peak to peak at gain 100 |
| CMRR | 135 dB minimum |
| PSRR | 130 dB minimum |
| Open loop gain | 130 dB minimum |
| Unity gain crossover | 4 MHz typical |
| Supply range | 2.2 V to 5.5 V single supply |
| Operating temperature | -40 C to +125 C |
Two channels at the same temperature
The drift of each channel is 0.015 microvolts per degree C, which is 2.475 microvolts over the 165 kelvin span, and the two channels share a die. A differential measurement built from both therefore sees the drift largely cancel, because the two are at the same temperature and the same process. The document does not publish a tracking figure, so the safe budget is still the sum, 4.95 microvolts.
The offset is the term that does not cancel. Two channels at 2.5 microvolts maximum each give 5 microvolts of worst case offset on the difference, which at a gain of 101 is 0.505 millivolts. Against a 16 bit converter with a 2.5 volt reference that is 13 least significant bits, so the channel still needs a zero step in production if absolute accuracy is the requirement.
135 decibels of CMRR on a low voltage amplifier
A minimum CMRR of 135 decibels means a 1 volt common mode change produces about 0.18 microvolts of input referred error. That is what makes a 2.2 to 5.5 volt part usable on a bridge whose common mode sits nowhere near mid supply: the common mode error stays below the offset, so the channel's accuracy is set by the offset and the drift rather than by the bridge's bias point.
The PSRR of 130 decibels minimum does the same job for the supply. A 100 millivolt step on the rail produces about 0.03 microvolts of input referred error, so a shared rail with a converter's digital current on it does not automatically ruin the channel. It does not excuse poor decoupling, because the specification is for the pin, not for the board.
Where a dual chopper stops being the right answer
The 4 megahertz crossover limits a gain of 100 stage to about 30 kilohertz of closed loop bandwidth. A vibration channel that needs 100 kilohertz at that gain needs a different amplifier, and the 2.8 nanovolt family gives 100 kilohertz at a gain of 100 with a 0.6 microvolt per degree C drift.
A second limit is the 5.5 volt maximum supply. A 15 volt industrial rail cannot feed this part directly, so a channel on a 15 volt rail either drops to a 5 volt rail for the front end or moves to the 55 volt zero drift family, which publishes 5 microvolts of offset instead of 2.5.
Where a customer needs a second position on this part, the ADI second source page is the starting point, medical device components sets out the checks a substitution has to pass, and BOM shortage recovery is the short lead time route we quote against.
Two questions buyers ask
Do the two channels track each other over temperature? The document does not publish a tracking figure. They share a die, so the drift largely cancels in a difference measurement, but the safe budget is the sum of two maxima, 4.95 microvolts across 165 kelvin.
Is the dual a drop in for two singles? The electrical table is the same per channel and the footprint is not: an 8-lead dual replaces two 8-lead singles only with a board revision, and the supply decoupling moves to shared pins.