ADA4077-2ARZ
Product Specifications
ADA4077-2ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADA4077-2ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADA4077-2ARZ: two A grade channels in one 8-lead SOIC
The ADA4077-2ARZ carries two independent amplifiers of the same A grade in a single 8-lead SOIC. Each amplifier is published at 50 microvolts of maximum offset at 25 degrees C and 0.55 microvolts per degree C of maximum drift. Two channels in one package is the usual way a two sensor channel or a difference stage is built, and the arithmetic that matters is that the errors double while the package and the decoupling stay single.
Published values
| Parameter | Value |
|---|---|
| Channels | 2 |
| Package | 8-lead SOIC (R-8), also offered in 8-lead MSOP |
| Offset voltage, A grade | 50 uV maximum at 25 C, per amplifier |
| Offset voltage drift, A grade | 0.55 uV/C maximum, 8-lead |
| Input bias current | 1 nA maximum at 25 C |
| Voltage noise density | 6.9 nV/root Hz typical at 1 kHz |
| CMRR, PSRR, open loop gain | 120 dB minimum each |
| Gain bandwidth product | 3.9 MHz typical at 5 V supply |
| Supply current | 400 uA per amplifier typical, 650 uA per amplifier maximum |
| Absolute maximum supply | 36 V |
| Operating temperature | -40 C to +125 C |
| Moisture sensitivity | MSL1 rated |
Two error budgets in one package
A dual is priced per channel better than two singles, but nothing about the package couples the two offsets. Each amplifier is specified on its own at 50 microvolts maximum, so a difference stage built from the two channels has to carry 100 microvolts as the worst case sum, not 50. That is the figure to put in a budget that a customer will test at incoming inspection.
The drift adds the same way: 0.55 microvolts per degree C per channel, and 165 kelvin of span puts 90.75 microvolts on each channel, 181.5 microvolts on the difference. If the two channels sit on opposite sides of a bridge they will usually track because they sit in the same package at the same temperature, but the datasheet does not promise a tracking figure, so the sum of the two maxima is the honest budget.
Supply current for the package, not the channel
Quiescent current is quoted per amplifier at 400 microamps typical and 650 microamps maximum, so the package draws up to 1.3 milliamps before any output current. On a 15 volt rail that is 19.5 milliwatts in the package, and the 8-lead SOIC thermal resistance quoted in the same document is 158 degrees C per watt junction to ambient, which puts the junction about 3 kelvin above ambient at that dissipation. Output current, not quiescent current, is what moves the junction.
Both amplifiers share the supply pins and the decoupling. A single 0.1 microfarad capacitor per rail close to the package is the published recommendation, and it is also the point where a board that shares one capacitor between two channels can inject one channel's output current into the other channel's supply.
When a dual is the wrong choice
A dual is the wrong choice when the two channels need different bandwidths or different supplies. The gain bandwidth product is 3.9 MHz at 5 volts for both amplifiers, and compensation is internal, so a channel that needs to be slowed down has to be slowed externally. Two singles give independent compensation; one dual gives a smaller board and a lower price per channel.
The second case is a channel that has to stay powered while the other is shut down. The dual has one supply pin pair, so the two channels power down together, and a circuit that needs one channel awake has to use two single packages.
For a board that has to keep running while a reel runs out, the ADI second source page is where the family alternatives sit, the pin to pin cross reference is the check list before a substitute goes in, and component lead time solutions is how a gap is covered without a new line item.
Two questions buyers ask
Do both channels carry the same grade? Yes. The A grade applies to the whole order code, and the 50 microvolt maximum is published per amplifier. There is no separate grade per channel inside one package.
Can the two channels be used as a differential pair? They can, but the document does not publish a channel to channel matching figure, so the safe budget for a difference measurement is the sum of two maxima: 100 microvolts at 25 degrees C and 181.5 microvolts across the 165 kelvin span.