ADCMP562BRQZ
Product Specifications
ADCMP562BRQZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADCMP562BRQZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADCMP562BRQZ: 700 ps of Delay With 75 ps of Dispersion Across Overdrive
The ADCMP562 is a dual high speed comparator with positive emitter coupled logic outputs, a propagation delay of 700 ps, and a propagation delay dispersion of 75 ps across the overdrive range. Dispersion is the number that matters in a timing critical path: it states how much the delay moves when the input overdrive changes, and a comparator with a fast typical delay but a wide dispersion produces jitter that no downstream retiming can remove. The part also has a 700 ps minimum pulse width, a 1.5 GHz equivalent input rise time bandwidth, and an input common mode range from -2 V to +3 V.
The output standard, and why it is PECL
The outputs are emitter coupled logic levels referenced to the positive rail, so the switching current is drawn from the positive supply and the output stage does not have the slew limitation of a saturated logic family. Typical output rise and fall times are 500 ps, and the outputs are specified differentially, so the receiver should be a differential pair terminated into 50 ohm to two volts below the positive rail. A single ended load to ground changes both the level and the edge, and the 700 ps delay figure no longer applies. The quiescent current is set by the emitter followers and stays roughly constant whether the output is high or low, which is what keeps the supply current free of the data dependent component that would otherwise couple into the input.
Comparator hysteresis and the pin that sets it
The ADCMP562 has a programmable hysteresis pin, which the single member of the family lacks. Hysteresis is what stops a slow input from producing a burst of transitions at the threshold, and it is set by a resistor to ground on that pin. A signal that crosses the threshold with 1 mV of noise and no hysteresis produces a train of edges rather than one, and the counter behind the comparator then records a false event. The cost of hysteresis is a shifted threshold, so it should be set just above the expected noise and no higher.
| Parameter | Value | What it decides |
|---|---|---|
| Propagation delay | 700 ps | Equivalent to 1.43 GHz of timing resolution |
| Delay dispersion | 75 ps | Jitter across the overdrive range |
| Minimum pulse width | 700 ps | Edges closer than this are not resolved |
| Output rise and fall | 500 ps typical | The edge dominates the timing budget |
| Output family | Differential PECL | Terminate to two volts below the positive rail |
| Input common mode | -2.0 V to +3.0 V | Below ground sensing with a single supply |
| Power supply rejection | Greater than 85 dB | 100 mV of rail noise gives 5.6 uV referred in |
| Hysteresis | Programmable, 562 only | Stops a burst of edges on a slow input |
| Latch control | Differential latch enable | Holds the decision for a defined window |
| Input protection | Robust, differential stage | Survives a signal while unpowered |
| ESD | 4 kV HBM, 200 V machine model | Handling and board level protection |
| Package | 20-lead QSOP, 16-lead for the single member | Pin count follows the latch and hysteresis pins |
Delay against the clock period
At 700 ps of delay, a 1 GHz clock period of 1000 ps leaves 300 ps for the input path and the load, which is why this class of comparator appears in time to digital converters and in automatic test equipment pin electronics rather than in general purpose threshold detection. The 75 ps of dispersion is 7.5 percent of that period, so a front end that depends on a fixed delay has to either calibrate it out or run at a lower rate. The 1.5 GHz equivalent input bandwidth means the input stage itself does not limit a 500 ps edge.
Supply, decoupling and the latch
With 85 dB of power supply rejection, 100 mV of high frequency noise on the positive rail appears as 5.6 uV referred to the input, which is small against the hysteresis a board will typically set. The decoupling still has to be local, because the rejection figure falls with frequency and the output edges draw a current step from the same rail. The differential latch enable holds the output state for as long as it is asserted, which is how a comparator is made to sample a narrow window rather than respond continuously.
Buying a comparator for a timing path
The three numbers to compare across candidates are delay, dispersion and minimum pulse width, and a part that quotes a faster delay with a wider dispersion is not an improvement. Order code and package have to be kept together, because the hysteresis and latch pins are not on every member of the family. Availability is handled through ADI part second source, and the wider question of matching a comparator to its converter is set out in ADC DAC cross reference. Where a short part forces a change, the verification steps are in how to verify a drop in replacement.