DAC8532IDGKR
Product Specifications
DAC8532IDGKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DAC8532IDGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DAC8532IDGKR: the dual 16-bit converter in the eight pin VSSOP
The DAC8532IDGKR is a two channel, 16 bit voltage output converter in an eight pin VSSOP, packed 2500 pieces on a large tape and reel. The vendor carries the part as ACTIVE and lists a supply of 2.7 V to 5.5 V, 16 bit monotonicity over temperature, a supply current of 500 microamps at 5 V, a settling time of 10 microseconds to 0.003 per cent of full scale, an ultra low AC crosstalk figure of 100 decibels typical, a three wire serial interface that runs to 30 MHz at 5 V, a power on reset to zero scale, a power down mode that draws 200 nanoamps at 5 V, and an operating range of minus 40 to plus 105 degrees.
The eight pin body is the point of the part. A dual 16 bit converter with an on chip output amplifier, a reference input and a serial port normally takes fourteen or sixteen pins, and this one takes eight by bringing the two outputs out on adjacent pins and putting the reference on a single shared pin. The trade is that both channels share one reference, so the two spans cannot be set independently, which is exactly the opposite of the octal part that carries two reference pins.
The DAC8532IDGKR rows as the addendum publishes them
| Part class | Dual channel 16 bit voltage output converter |
| Vendor status | ACTIVE, production data |
| Data sheet | SBAS246B, December 2001, revised November 2014 |
| Supply range | 2.7 V to 5.5 V |
| Resolution | 16 bits per channel, two channels |
| Relative accuracy | 0.0987 per cent of full scale range |
| Differential nonlinearity | 1 LSB maximum, 16 bit monotonic over temperature |
| Zero code error | 5 mV typical, 25 mV maximum |
| Full scale error | 0.15 per cent typical, 1 per cent maximum |
| Gain error | 1 per cent of full scale range |
| Zero code drift | 20 microvolts per degree |
| Gain temperature coefficient | 5 parts per million of full scale per degree |
| Settling time | 10 microseconds to 0.003 per cent, 12 with 500 pF load |
| Slew rate | 1 volt per microsecond |
| Glitch impulse | 20 nanovolt seconds |
| AC crosstalk | 100 decibels typical, 96 minimum |
| DC crosstalk | 0.25 LSB around major carry |
| Reference input | 0 V to supply, 75 kilohm impedance |
| Reference current | 67 microamps typical at 5 V, 40 at 3 V |
| Serial clock | 30 MHz at 5 V |
| Input register | 24 bit, double buffered, simultaneous or sequential update |
| Supply current | 500 microamps typical, 800 maximum at 5 V |
| Power down current | 200 nanoamps typical at 5 V |
| Body | VSSOP, 8 pins, 3.00 by 3.00 millimetres |
| Reel row | DAC8532IDGKR, 2500 pieces, large tape and reel |
| Tube row | DAC8532IDGK, 80 pieces, tube |
| Moisture level | Level 2 at 260 degrees, one year floor life |
| Thermal | 164 degrees per watt junction to ambient |
The tube row is 80 pieces and the reel row is 2500, and both are in the same body, so a prototype and a production order differ only in packing. The moisture level is 2 with a one year floor life, which is a longer window than a level 3 part and a shorter one than a level 1 part. The marking on the body is D32E, which is what a receiving inspection will read rather than the orderable string.
What the electrical table fixes
The relative accuracy figure of 0.0987 per cent of full scale is 64 LSB on a 16 bit converter, which sounds worse than the monotonicity claim and does not contradict it. Monotonicity says the output never steps backwards as the code increases, accuracy says where the output sits against an ideal line, and the two are separate tests. A part that is monotonic to 1 LSB and accurate to 64 LSB is a part that is linear in small steps and offset in absolute terms, and an end system that calibrates offset and gain removes most of the second number.
The zero code error of 5 mV typical and 25 mV maximum is the dominant error at low codes, which is where a 4 to 20 mA loop built from a voltage converter spends its time. At a 2.5 V reference one LSB is 38 microvolts, so a 25 mV zero error is 650 LSB, and a customer who expects 16 bit resolution near zero scale has to calibrate or accept the part is a 12 bit converter at the bottom of its range. This is the single most common misunderstanding with rail to rail converters and it is worth stating before a quote.
The supply current of 500 microamps typical at 5 V and the 200 nanoamp power down figure are what make the part usable in a loop powered instrument. A 4 to 20 mA transmitter has 4 mA to spend on everything, and two channels at 500 microamps plus a reference is a large fraction of it. The reference current of 67 microamps at 5 V has to be added to that, and a reference with a low output impedance is what keeps the total predictable.
Where the body fits on a board
At 3.00 by 3.00 millimetres the eight pin VSSOP is one of the smaller dual 16 bit packages available, and the 164 degree per watt junction to ambient figure is the price of that size. At 500 microamps and 5 V the part dissipates 2.5 milliwatts, so the thermal rise is under half a degree and the number is irrelevant in normal operation; it becomes relevant only if an output is shorted, and the short circuit current is 50 mA at 5 V against 20 mA at 3 V.
The capacitive load stability row is the constraint that actually bites. The output is stable into 1000 picofarads with a 2 kilohm load and into a smaller load only with care, and a board that puts a 10 nanofarad capacitor on the output of a converter to filter noise will oscillate. The vendor prints a slew rate of 1 volt per microsecond and a settling time of 12 microseconds with 500 picofarads, which is the number to use when the load capacitance is known rather than the 10 microsecond headline.
What the documents do not publish
The product page gives no output noise figure in microvolts rms and no noise density, only a signal to noise ratio of 94 decibels in the AC table, which is a full scale ratio rather than a spot noise figure. For a converter driving a transducer amplifier the spot noise at the code of interest is the number that matters, and it has to come from the typical characteristics rather than from the summary. The page also gives no long term drift figure beyond the temperature coefficients.
The interface description does not state the power up sequence requirement in the summary, only in the revision history note that no device pin should be brought high before power is applied. That is a real constraint on a board with a separate digital rail, and it is the kind of note that gets lost when a customer copies the pin description into a new board without reading the section that follows it.
Second source and long term availability
Dual 16 bit converters in an eight pin body exist from a small number of vendors and the pin out is not standardised, so a cross is usually a board change. The candidates also differ in whether the reference is shared and in the power down current, both of which change the end behaviour. The ADC DAC cross reference page sets out the comparison, and the how to verify a drop in replacement page covers the bench work.
The document is dated 2014 in its current revision and the addendum rows we read are dated after that, so the part is still in the vendor catalogue with live rows. A 25 year old converter with an unchanged pin out is usually a safe long term bet, but the body is small and the die is old, and a customer with a ten year programme should ask for a written availability statement rather than rely on the status column.
What to send with an enquiry
Send the exact string, the body, the quantity and the date you need it. State the reference voltage and where it comes from, because the reference current is drawn from the source and a divider is not a reference. State the load capacitance, since that decides whether the settling figure is 10 or 12 microseconds.
If both channels are updated together, say so, because the simultaneous update mode uses the double buffered register and changes the framing on the serial line. The BOM scrubbing page explains how we reconcile a line like this against the build quantity before a schedule is confirmed.