Contact Us

L78M05CDT-TR

Brand: ST
L78M05CDT-TR is a linear voltage regulator from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine L78M05CDT-TR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

L78M05CDT-TR — Voltage Regulator by STMicroelectronics

The L78M05CDT-TR is an STMicroelectronics voltage regulator in TO-252-2(DPAK) for reliable power management in embedded and industrial applications.

Part Number Decoded — Field by Field

FieldValueMeaning
L78M05CDT-TRFull Part NumberSTMicroelectronics Voltage Regulator

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberL78M05CDT-TR
PackageTO-252-2(DPAK)
TypeFixed/Adjustable Voltage Regulator
QualificationIndustrial (-40°C to +125°C)

Product Overview

The L78M05CDT-TR is an STMicroelectronics voltage regulator in TO-252-2(DPAK) package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.

Key Features & Benefits

Stable Output with Built-in Protection

Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.

Wide Compatibility & Minimal External Components

Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.

Industrial Temperature Range

Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.

Target Applications

Drone & Embedded System Power Rails

Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.

Industrial & Automotive Electronics

Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.

General-Purpose Point-of-Load Regulation

Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.

Frequently Asked Questions

What is the output voltage of the L78M05CDT-TR?

Check the specific variant. The L78M05CDT-TR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.

What capacitors are needed for stability?

Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics L78M05CDT-TR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.

L78M05CDT-TR: the 500 mA 5 V regulator at 4 percent, for rails that only need to be near 5 V

L78M05CDT-TR is the C grade of the same 5 V L78M regulator, in the DPAK body, tape and reel. It holds 4 percent, so 4.8 to 5.2 V at room temperature and 4.75 to 5.25 V across a load of 5 to 350 mA, and it keeps the 0.5 A rating, the current limit, the thermal shutdown and the output transition safe operating area protection of the family. The vendor document is DS0425, revision 24, dated September 2020.

The C grade is the version to choose when the load tolerates the wider window and the volume is real. Relays, lamps, fans, display backlights and the coil side of a driver all work inside 4.75 to 5.25 V. A rail that feeds a CAN transceiver, an ADC reference or a precision bridge does not, and that is where the A grade or a low dropout part takes over. The distinction is worth a line on the purchase order, because the two codes differ in price and nothing in the datasheet hides it.

What the C grade table prints for 5 V

Output voltage at 25 degrees4.8 to 5.2 V, plus or minus 4 percent
Output voltage over load4.75 to 5.25 V, 5 to 350 mA, input 7 to 20 V
Output current0.5 A with adequate heat sinking
Test input voltage10 V at 350 mA
Line regulation50 mV maximum, 7 to 25 V at 200 mA
Load regulation100 mV maximum, 5 to 500 mA
Quiescent currentQuoted in milliamperes for this family, the price of a bipolar pass element
Supply voltage rejection62 dB typical, 10 Hz to 100 kHz
Output voltage driftminus 0.5 millivolts per degree typical
ProtectionsCurrent limit, thermal shutdown, output transition safe operating area
Package on this codeDPAK, tape and reel
Other packages in the familyTO-220, TO-220FP, IPAK
Temperature rangeExtended range guaranteed, 0 to 125 degrees for the C grade

The two things that decide the copper under the tab

The first is copper. A DPAK carries its heat through the tab into the board, so the pour under the tab, the number of vias into the ground plane and the thickness of that plane are the heatsink. At 300 mA from a 12 V input the part dissipates 2.1 W and no reasonable pad on a two layer board will hold that at 70 degrees. At 150 mA from the same input it dissipates 1.05 W, which a DPAK on a 2 square centimetre pour with six vias will hold.

The second is the input rail. The 5 V C grade is tested at 10 V in, which is where the vendor measured its line and load regulation, and a board that feeds it from a 7.5 V rail is working much closer to dropout than the table suggests. Two volts of dropout at 350 mA leaves 5 V out of a 7 V input only just, and any sag on the input appears directly on the output.

Use and the related pages

The part is common on industrial control boards, on the logic side of motor drive cards, and as the 5 V rail of an instrument that already has a linear front end. Related pages are power management cross reference, how to reduce component cost for the grade trade, and one stop BOM sourcing.

Questions buyers ask on this code

Whether the C grade can sit where the A grade was drawn is the first, and the answer depends on the load window and the temperature range rather than on the footprint. The second is whether the DPAK needs a separate heatsink, and it does not as long as the copper is in the drawing. The third is the reel quantity on the TR suffix, which is worth confirming before a line is scheduled, because the DPAK tape width is not the same as the SO-8 tape that the smaller parts use.