LD1117S33TR
Product Specifications
LD1117S33TR — 3.3V, 800mA Low Dropout Voltage Regulator by STMicroelectronics
The LD1117S33TR is STMicroelectronics' 3.3v, 800ma low dropout voltage regulator. Supplied by SUPERB Automation.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| LD1117S33TR | Full Part Number | 3.3V, 800mA Low Dropout Voltage Regulator |
Quick Specifications
| Parameter | Value |
|---|---|
| Output Voltage | 3.3V Fixed |
| Output Current | 800mA |
| Dropout Voltage | 1.1V @800mA |
| Input Voltage Range | Up to 15V |
| Line Regulation | 0.2% |
| Load Regulation | 0.4% |
| Package | SOT-223 |
| Protection | Thermal shutdown, current limit |
Product Overview
3.3V, 800mA Low Dropout Voltage Regulator from STMicroelectronics. Supplied by SUPERB Automation with full traceability and batch-level QA documentation.
Key Features & Benefits
Fixed 3.3V Output — No External Resistors Needed
The LD1117S33TR provides a fixed 3.3V output with ±1% accuracy, eliminating the need for external feedback resistors. Simply add input and output capacitors for a complete power supply — ideal for powering 3.3V MCUs, sensors, and RF modules in drone systems.
800mA Output — Powers Complex Sensor Suites
With 800mA continuous output current, the LD1117S33TR can power a full drone sensor suite including IMU, barometer, magnetometer, GPS receiver, and radio receiver — all from a single LDO, reducing BOM count compared to multiple smaller regulators.
Thermal & Current Protection — Drone-Ready Reliability
Built-in thermal shutdown and current limiting protect both the regulator and downstream electronics from fault conditions. In drone applications where confined spaces challenge thermal management, these protections prevent cascade failures.
Target Applications
Drone Flight Controller Power Supply
Provides the 3.3V main rail for STM32-based flight controllers (F1, F3, F4, F7, H7 families), powering the MCU, all SPI/I²C sensors, and UART peripherals from a 5V bus or direct LiPo input (up to 4S).
Sensor & Communication Module Power
Powers GPS/GLONASS modules (u-blox NEO-M8/M9), ExpressLRS/Crossfire receivers, analog and digital VTX units, and companion communication modules with clean, regulated 3.3V.
General Embedded & IoT Power Regulation
Ubiquitous in embedded systems, Arduino shields, Raspberry Pi HATs, and IoT devices as the go-to 3.3V regulator — backed by decades of proven reliability.
Frequently Asked Questions
What capacitors are required for the LD1117S33TR?
A 10µF tantalum or ceramic capacitor on the output is recommended for stability. The LD1117 is stable with ESR from 0.3Ω to 22Ω. For ceramic output capacitors, ensure the ESR is within this range or add a small series resistor.
Can the LD1117S33TR be powered directly from a LiPo battery?
Yes, for up to 4S LiPo (16.8V max). The input voltage rating is 15V absolute maximum, so for 4S operation use a pre-regulator or ensure your fully-charged 4S pack is within tolerance. For 6S, use a buck converter before the LDO.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics LD1117S33TR with full traceability and competitive lead times. Contact us with your target quantity — we'll respond with a quotation within 24 hours.
LD1117S33TR: 800 mA at 3.3 V in SOT-223 with 1 V dropout and 1 percent at 25 degrees
LD1117S33TR is the fixed 3.3 V member of the LD1117 low dropout family from STMicroelectronics, in the SOT-223 body, tape and reel. It delivers up to 800 mA, has a typical dropout of 1 V rather than the 2 V of a classic 78 series part, holds plus or minus 1 percent at 25 degrees and 2 percent over the full temperature range, and reaches 75 dB of supply rejection. The document that covers the family is DocID2572, revision 38, dated January 2025.
The pass element is an NPN transistor rather than a PNP, and that choice is what the datasheet keeps pointing at. With an NPN the quiescent current flows mostly into the load instead of out of the ground pin, so the efficiency at high current is better than a PNP low dropout part of the same age. The price of the NPN structure is a minimum output capacitor, 10 microfarads in the vendor text, and a build that leaves it out will oscillate rather than regulate.
Figures for the fixed 3.3 V part
| Output voltage | 3.3 V, plus or minus 1 percent at 25 degrees, 2 percent over temperature |
| Output current | 800 mA |
| Dropout voltage | 1 V typical |
| Supply voltage rejection | 75 dB typical |
| Minimum output capacitor | 10 microfarads, a standard aluminium or tantalum part is enough |
| Protections | Internal current limit and thermal limit |
| Pass element | NPN, quiescent current flows mostly into the load |
| Fixed voltages in the family | 1.2, 1.8, 2.5, 3.3 and 5.0 V, plus an adjustable version at 1.25 V reference |
| Packages in the family | SOT-223, DPAK, SO-8, TO-220 |
| Package on this code | SOT-223, tape and reel |
| Thermal note | SOT-223 and DPAK are the two bodies the vendor names for thermal performance |
Why the 1 V dropout changes the rail plan
On an L78L a 3.3 V output needs 5.3 V in before the part is in regulation. On this part the same output needs about 4.3 V, so a 5 V rail that sits at 4.9 V under load is still inside the window instead of outside it. That single volt is the difference between a post regulator that works behind a 5 V buck and one that drops out on every load step, and it is the main technical reason the LD1117 family replaced the older 78 series parts in so many builds.
At 800 mA and 1.6 V of headroom the part dissipates 1.28 W. In a SOT-223 with a tab soldered to a copper island that is manageable at a moderate ambient, and in the same body without copper it is not. The vendor names the SOT-223 and the DPAK as the two bodies with the thermal characteristics worth using, which is a polite way of saying that the SO-8 version of the family is for light loads only.
Where it is used and what follows on
The typical loads are 3.3 V logic, memory and PHY rails, radio module supplies and the analogue side of a data converter. In SUPERB builds this part often sits behind a 5 V intermediate rail on a telecom line card or on the control board of a medical instrument. Related pages are power management cross reference, pin to pin cross reference for the AMS1117 class alternatives, and component traceability report for the record that keeps a substitution honest.
Questions buyers ask on this code
Whether the 10 microfarad output capacitor is really required is the first, and the answer is yes: this is a stability condition and not a recommendation. The second is the difference between this code and the C code that sits beside it in the order table, which is a grade marker in the part number and should be confirmed in writing on the purchase order. The third is the SOT-223 tab, which on most boards is the only thermal path the part has, so the copper area belongs in the fabrication drawing rather than in a note.