Contact Us

CD4093BM96

Brand: Texas Instruments
Texas Instruments CD4093BM96 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4093BM96 — Power Management & Signal Chain | Superb Automation

CD4093BM96

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4093BM96 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4093BM96: the Schmitt trigger NAND on a 2500 piece SOIC reel

The CD4093BM96 is the large tape and reel entry for the CD4093B, four two input NAND gates with Schmitt trigger inputs in a 14-lead small outline body. The vendor page lists the device as ACTIVE with a drive of 6.8 mA in both directions, an 8 Mbps data rate and an operating range of minus 55 to plus 125 degrees. The reel row is 2500 pieces, level 1 at 260 degrees, nickel palladium gold finish, and the marking on the body is CD4093BM rather than the orderable string.

The reel is the volume format for the same die that sits in the plastic DIP. What changes is not the function but the assembly: the SOIC is 51.9 square millimetres against 181.42 for the DIP, the pitch is 1.27 mm, and the reel is 330 mm in diameter and 16.4 mm wide with a pocket 6.5 by 9.0 mm and an 8 mm pitch. A feeder already set for the family runs this reel without a change, which is why the SOIC reel is the default choice for a board that is already surface mount.

The CD4093B rows as the addendum publishes them

Part classFour two input NAND gates, Schmitt trigger inputs
Vendor descriptor4-ch, 2-input NAND, Schmitt-Trigger input
Vendor statusACTIVE, catalogue rating
Data sheetSCHS097 or later revision, acquired from Harris Semiconductor
Package addendum date18 September 2026
Supply range3 V to 18 V, 20 V type rating in the headline
Output drive6.8 mA sink and source at 15 V
Data rate8 Mbps in the parametric table
Hysteresis at 5 V0.9 V typical
Hysteresis at 10 V2.3 V typical
Noise immunityGreater than 50 per cent of the rail
Input rise and fallNo limit, per the feature list
Input current1 microamp at 18 V over temperature, 100 nA at 25 degrees
SOIC body14 leads, 51.9 square millimetres, 8.65 by 6 mm
SOIC tube rowCD4093BM, 50 pieces, Active
SOIC reel rowCD4093BM96, 2500 pieces, Active
Small reel rowCD4093BMT, Obsolete, blank quantity, Call TI
SOP reel rowCD4093BNSR, 2000 pieces, Active
TSSOP rowsCD4093BPW tube Obsolete, CD4093BPWR reel 2000 Active
PDIP rowCD4093BE, 25 pieces in a tube, Active
Ceramic rowsCD4093BF and CD4093BF3A, 25 pieces, Active
Marking on the reelCD4093BM, the same marking as the tube row

Both the tube and the reel are active for this body, which makes the SOIC the easiest of the four formats to buy. The small reel is the only closed surface mount row, and a customer who asks for 250 pieces is asking for a format that no longer exists. The honest answer is a cut reel or the 2000 piece SOP reel, and the choice depends on whether the board can take a different footprint.

What the Schmitt trigger does to the numbers

The hysteresis window is 0.9 V at 5 V and 2.3 V at 10 V, and the vendor states noise immunity greater than 50 per cent with no limit on input rise and fall times. Those three figures are what allow the gate to be used as a receiver for a slow signal. A 100 k resistor and a 1 microfarad capacitor give a time constant of a tenth of a second, and an ordinary CMOS gate would oscillate through the whole crossing while this one switches once per direction.

The drive is 6.8 mA at 15 V and falls to about 1 mA guaranteed at 5 V, so the output can drive another CMOS input directly and cannot drive a relay or a lamp without a transistor. The input current of 1 microamp at 18 V is the leakage a pull up has to supply, and it is small enough that a 1 megohm pull up still holds the input more than a volt away from the threshold.

The propagation delay is not on the product page, and the electrical tables in our copy of the data sheet are images. The page therefore reports the hysteresis and the drive and states that the delay is not quoted here, rather than borrowing a family typical from a different gate. A customer who needs a guaranteed delay has to read the printed table at the rail in question.

Where the SOIC reel is the right format

A 2500 piece reel covers 2500 placements, whether that is 2500 boards with one gate each or 1250 boards with two, and it is the format that keeps a pick and place line running. The tube at 50 pieces is the format for a prototype and for a repair kit. At 51.9 square millimetres the SOIC is a third of the plastic DIP area, and at 1.27 mm pitch it does not need the finer stencil that a TSSOP demands.

The thermal impedance of the SOIC is 86 degrees per watt in the family document, against 80 for the plastic DIP and 113 for the TSSOP. At static currents the number is not a constraint, and in a fault it is the TSSOP that reaches its limit first. That is one reason the 2500 piece SOIC reel is the body most often chosen for industrial boards that may see a miswired input in the field.

What the documents do not publish

No propagation delay, no supply current and no maximum input frequency appear on the page. The hysteresis is quoted at 5 V and 10 V and not at 15 V. The data sheet carries the full tables and the test circuit, and the page states which of its numbers came from where. That distinction matters when a customer sends the page as a requirement document, because the page is a summary and not a specification.

The astable configuration is the other common use. One gate, one resistor and one capacitor make an oscillator, and because the input has hysteresis the circuit starts reliably and does not sit at a bias point where a plain inverter would stall. The vendor lists astable multivibrators among the applications, and the same document shows the monostable form for a one shot. Both circuits depend on the hysteresis window, so both change when the part is substituted for a gate without one.

The tape and the package outline are in the same document set and they are what an assembly engineer asks for first. The 330 mm reel fits the standard feeder, the 16.4 mm tape width is the same as the rest of the 14-lead SOIC family, and the pocket depth of 2.1 mm clears the 1.75 mm body height. A reel that does not fit the feeder is a line stop on the first day of production, and it is the kind of detail that a part number page should not leave to a phone call.

The board side is simpler. At 1.27 mm pitch the SOIC can be placed and inspected with the same stencil and the same optical check as the rest of the 4000 series parts on the board, so a mixed board does not need a second process. That is the practical argument for staying with this body when the area budget allows it.

Second source and long term availability

The CD4093B is second sourced under the same number and the reel is live, so availability is not a near term concern. The substitution to watch is a 74HC132, which has a narrower window and a faster edge, so a debounce that relied on the wide hysteresis will pass a bounce it used to reject. The pin to pin cross reference page sets out the checks, and the date code management page covers how a reel is rotated so the oldest date code ships first.

What to send with an enquiry

Send the string, the body, the quantity and the date. If the board is surface mount, confirm whether a 2500 piece reel is acceptable, because the 250 piece small reel is closed and a partial reel is the only way to buy less. If the input is a mechanical switch, say so, because the hysteresis window and the pull up value have to be checked together. The kitting service page explains how a mixed bill of materials is picked against a build.