VN7010AJTR
Product Specifications
VN7010AJTR — Integrated Motor Driver / Smart Power Switch by STMicroelectronics
The VN7010AJTR is an STMicroelectronics integrated motor driver / smart power switch in PowerSSO-16 for automotive and industrial actuator control applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| VN7010AJTR | Full Part Number | STMicroelectronics Motor Driver / Power Switch |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | VN7010AJTR |
| Package | PowerSSO-16 |
| Type | Integrated Motor Driver / Smart Power Switch |
| Qualification | Automotive AEC-Q100 / Industrial |
Product Overview
The VN7010AJTR is an STMicroelectronics integrated motor driver / smart power switch in PowerSSO-16 package. Featuring ST's VIPower technology with monolithic integration of power MOSFETs, gate drivers, and protection/diagnostic circuitry, it simplifies motor control and high-side/low-side switching designs with reduced BOM count and enhanced reliability.
Key Features & Benefits
VIPower Monolithic Integration — Power + Control in One Package
ST's VIPower technology integrates N-channel power MOSFETs, gate drivers, charge pump, and comprehensive protection circuitry on a single die — eliminating external MOSFETs, bootstrap diodes, and sense resistors.
Comprehensive Protection & Diagnostics
Built-in overcurrent, overtemperature (thermal shutdown), undervoltage lockout, and load-dump protection with diagnostic feedback (current sense output, fault status flag) enables self-protecting designs suitable for safety-critical and autonomous systems.
Automotive-Grade Robustness
Designed to withstand harsh automotive and industrial environments including load dump, reverse battery, and extended temperature range for reliable operation in drone payload systems, robotics, and vehicle applications.
Target Applications
Drone Payload & Actuator Control
Drives brushed DC motors, solenoids, and resistive/inductive loads in drone gimbal systems, payload release mechanisms, landing gear actuators, and auxiliary power switching.
Automotive Body & Powertrain
Targets automotive applications including throttle control, EGR valves, HVAC actuators, mirror folding, headlamp leveling, and relay/lamp drivers — all requiring AEC-Q100 qualification.
Industrial Automation & Robotics
Powers motor control, valve actuation, and power distribution in industrial robots, conveyor systems, automated guided vehicles (AGVs), and factory automation equipment.
Frequently Asked Questions
What protection features does the VN7010AJTR include?
The VN7010AJTR features overcurrent protection, overtemperature shutdown, undervoltage lockout, and diagnostic feedback — ensuring robust, self-protecting operation in demanding environments.
Is external current sensing required?
No. The integrated current-sense output provides proportional load current feedback, eliminating the need for external shunt resistors and differential amplifiers.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics VN7010AJTR with full traceability and batch-level QA documentation. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.
VN7010AJTR: a 10 milliohm high side driver for headlamp loads
VN7010AJTR is a single channel automotive high side driver in the PowerSSO-16 body, on tape and reel, with 10 milliohm typical on resistance and a 91 A typical current limit. The data sheet names automotive headlamps as the intended load, and the numbers explain why: a lamp pair draws a large cold filament current for tens of milliseconds, and a switch with 10 milliohm and a 91 A limit survives that inrush without an external current limiter.
The part sits in the VIPower M0-7 family and shares its diagnostic structure with the rest of the family. One multiplexed analog pin reports load current, supply voltage and chip temperature, and the logic pins select which one is presented. Fault detection covers overload, short to ground, short to supply, off state open load and thermal shutdown, with a configurable latch off and a dedicated reset pin.
Figures come from the VN7010AJ data sheet read this round, including the 40 V transient rating, the 4 V to 28 V operating window, the 10 milliohm per channel, the 91 A current limit and the 0.5 microamp maximum standby current.
The electrical window and the thermal table
| Function | Single channel high side driver with MultiSense analog feedback |
| Maximum transient supply | 40 V |
| Operating range | 4 V to 28 V |
| On resistance | 10 milliohm typical per channel |
| Current limit | 91 A typical |
| Standby current | 0.5 microamp maximum |
| Junction to ambient | 55 degrees per watt on a four layer board, 21.2 degrees per watt with 2 square centimetres of copper |
| Junction to board | 3.9 degrees per watt |
| Junction range | Minus 40 to plus 150 degrees |
| Storage range | Minus 55 to plus 150 degrees |
| ESD | 4 kV human body model on supply, input and output, 750 V charged device model |
| Logic levels | 3 V and 5 V CMOS compatible |
| Package | PowerSSO-16 |
| Qualification | AEC-Q100 |
What 10 milliohm buys and what it does not
At 10 milliohm, 10 A costs 1 W and 20 A costs 4 W. Compared with a 140 milliohm channel, the same 4 W carries fourteen times the current, which is exactly the difference between a signal lamp driver and a headlamp driver. That is the reason the family is split by resistance rather than by package.
The thermal table still decides the continuous current. A 4 W load on a four layer board with 55 degrees per watt sits 220 degrees above ambient, which is outside the junction window, while the same loss with 2 square centimetres of copper and the 21.2 degrees per watt figure sits at 85 degrees. The two numbers are both in the document and they describe two different boards, so a quotation that ignores the copper under the package is quoting a part that will shut down.
The 91 A limit and the cold filament
A halogen filament at 25 degrees has roughly a tenth of its hot resistance, so a 55 W lamp on 13.5 V that draws 4 A hot can pull 30 A or more for the first few milliseconds. The 91 A limit and the power limitation behaviour let the channel ride through that inrush, and the limitation is what stops a shorted lamp holder from pulling the supply down. A driver with a 20 A limit would trip on the inrush of the same lamp.
LED lamps present the opposite problem: the inrush is short but the steady current is small, and off state open load detection with an LED load needs the pull up to be sized so the leakage through the LED does not read as a connected load. The data sheet has a section on that dimensioning.
Where it is used and how we supply it
Headlamps, fog lamps, daytime running lamps and other high inrush body loads on a 12 V rail. In a module that also drives small lamps, the 10 milliohm channel and a 140 milliohm channel can sit on the same board and share one diagnostic input through the sense enable pins.
We check the reel and the date code at goods in and hold the record against the finished board. The power management cross reference page lists the family by resistance, the component traceability report page describes the lot record we issue for automotive builds, and the one stop BOM sourcing route covers the rest of the module.
Three questions buyers ask about this string
Is the current limit 91 A per channel? Yes, it is a single channel device, and the figure is the typical limitation printed in the electrical table.
Can it drive a motor? It switches one direction only. A motor needs a bridge, and the bridge family is a different string.
Why does the thermal table give two junction to ambient figures? One is a four layer board and the other is a two layer board with a defined copper area. The board under the package decides which one applies.