CD4081BE
Product Specifications
CD4081BE
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4081BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4081BE: the quad two input AND gate in the 14-lead plastic DIP
The CD4081BE is the plastic dual in line entry for the CD4081B, four independent two input AND gates in a 14-lead body. The vendor page lists the device as ACTIVE with the descriptor 4-ch, 2-input, 3-V to 18-V AND gates, a drive of 6.8 mA in both directions, an 8 Mbps data rate and an operating range of minus 55 to plus 125 degrees. The tube row is 25 pieces with a nickel palladium gold finish, and the marking is CD4081BE.
This is the most used gate in the CD4000B catalogue and the one most often substituted without a check. Every body in the family is active, from the 25 piece tube to the 2500 piece reel, so a buyer has real choices and no lifecycle excuse. The catch is that the product page feature line calls the part high speed while the data sheet describes the same die as medium speed at 60 ns typical, and those two statements set different expectations for a timing path.
The CD4081B rows as the addendum publishes them
| Part class | Four independent two input AND gates |
| Vendor descriptor | 4-ch, 2-input, 3-V to 18-V AND gates |
| Vendor status | ACTIVE, catalogue rating |
| Data sheet | SCHS054 family document, acquired from Harris Semiconductor |
| Package addendum date | 18 September 2026 |
| Supply range | 3 V to 18 V, 20 V type rating in the headline |
| Output drive | 6.8 mA sink and source at 15 V |
| Data rate | 8 Mbps in the parametric table |
| Propagation delay | 60 ns typical at 10 V into 50 pF |
| Feature conflict | Page feature line says high speed, data sheet says medium speed |
| Input thresholds at 5 V | Low 1.5 V maximum, high 3.5 V minimum |
| Input current | 1 microamp at 18 V over temperature, 100 nA at 25 degrees |
| Noise margin | 1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V |
| PDIP body | 14 leads, 181.42 square millimetres, 19.3 by 9.4 mm |
| PDIP rows | CD4081BE, CD4081BE.A and CD4081BEE4, 25 pieces, Active |
| SOIC tube row | CD4081BM, 50 pieces, Active |
| SOIC small reel | CD4081BMT, 250 pieces, Active |
| SOIC large reel | CD4081BM96, 2500 pieces, Active |
| SOP reel row | CD4081BNSR, 2000 pieces, Active |
| TSSOP rows | CD4081BPW tube 90 pieces, BPWR reel 2000 pieces, Active |
| Ceramic rows | CD4081BF and CD4081BF3A, 25 pieces, Active |
| Military marking | 7702402CA on the F3A row |
Every row above is active, and that is worth stating plainly because the same document also carries the CD4073B and the CD4082B, where the tube rows are closed. A customer who groups the three AND functions into one line item and assumes one status for all of them will be wrong. The 2500 piece reel and the 50 piece tube both exist for this part, so a pilot build and a production run can use the same body.
What the parametric table fixes
The 60 ns typical propagation at 10 V is the honest number. The page feature line calling the part high speed sits beside a parametric table that lists a standard speed family and a data rate of 8 Mbps, and the data sheet uses the word medium for the same delay. For a timing budget the 60 ns typical is the figure to use, and the guaranteed maximum in the switching table is the figure to plan against.
Input thresholds at 5 V are 1.5 V low and 3.5 V high, at 10 V they are 3 V and 7 V, and at 15 V they are 4 V and 11 V. Those bands are narrow relative to the rail, which is why a CMOS input must never be left floating: an open pin sits near the middle, both transistors conduct, and the supply current rises from microamps to milliamps while the output oscillates. The 1 microamp input current at 18 V means a 100 k pull down holds the pin at 0.1 V, which is comfortably inside the low band at every rail in the table.
Drive is 6.8 mA at 15 V and falls to about 1 mA guaranteed at 5 V. A gate that drives a light emitting diode directly at 5 V will not meet the current, and a gate that drives another CMOS input has more than enough. That distinction is where most substitutions go wrong.
Where the plastic DIP is the right choice
The plastic DIP is 181.42 square millimetres against 51.9 for the SOIC, 79.56 for the SOP and 32 for the TSSOP. It is the body for a single sided board, a wave solder line, a socketed test fixture and a repair kit. The 25 piece tube is the cheapest way to keep four gates on a shelf, and for a small instrument that ships a few hundred units a year the tube is often the whole inventory plan.
The thermal impedance of the plastic DIP is 80 degrees per watt, the lowest in the family and better than the 86 of the SOIC and the 113 of the TSSOP. The part dissipates almost nothing in normal operation, so the number is a fault case figure. In a fault the DIP has the most copper and the lowest rise, which is one reason industrial boards that see field miswiring keep the wide body long after the rest of the board has moved to surface mount.
What the documents do not publish
No maximum delay, no output capacitance, no short circuit current and no latch up rating appear on the page. The truth table and the switching table at three rails are in the data sheet. The page also omits the difference between the A suffix rows and the plain rows in the addendum, which matters to a buyer who is matching an existing approved vendor list rather than ordering a new line.
Packaging follows the same pattern as the rest of the band. The 25 piece tube has no moisture level because a tube is not a reflow carrier, the 50 piece SOIC tube and the reels carry level 1 at 260 degrees, and the lead finish is nickel palladium gold on every plastic row. A customer who has been buying a tin lead finished part from a broker should be told that the current catalogue rows are lead free, because the board finish and the reflow profile have to match the part rather than the other way round.
There is also a testing note. The vendor states that the family is tested for quiescent current at 20 V, which is a stress corner rather than an operating point. That test catches leakage defects that a 5 V test misses, and it is one of the reasons the older 4000 series parts have a long field record in equipment that sits powered for years. The page does not print the test flow, but the statement is in the feature list of every device on the same document.
Second source and long term availability
The CD4081B is second sourced under the same number, and the 14-lead pin out is one of the oldest in the catalogue. The nearest functional alternative is a 74HC08, which is faster, has a different input threshold and drives more current, so a board that leans on the slow edge for debounce or for a deliberate race will behave differently. The pin to pin cross reference page covers the checks, and the supplier quality audit page covers how a second source is qualified before it is released to a line.
What to send with an enquiry
Send the string, the body, the quantity and the date. If the board is through hole, the 25 piece tube is the packing and a 500 piece build is twenty tubes. If the board is reflow, say which reel size the line can take, because this part is offered in 250, 2000 and 2500 piece reels and the right one depends on the changeover policy rather than on the price. The BOM scrubbing page explains how the reel sizes are matched to a build plan before a schedule is promised.