Contact Us

VIPER22ADIP-E

Brand: ST
VIPER22ADIP-E is a switching regulator IC from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine VIPER22ADIP-E with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

VIPER22ADIP-E — Voltage Regulator by STMicroelectronics

The VIPER22ADIP-E is an STMicroelectronics voltage regulator in DIP-8 for reliable power management in embedded and industrial applications.

Part Number Decoded — Field by Field

FieldValueMeaning
VIPER22ADIP-EFull Part NumberSTMicroelectronics Voltage Regulator

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberVIPER22ADIP-E
PackageDIP-8
TypeFixed/Adjustable Voltage Regulator
QualificationIndustrial (-40°C to +125°C)

Product Overview

The VIPER22ADIP-E is an STMicroelectronics voltage regulator in DIP-8 package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.

Key Features & Benefits

Stable Output with Built-in Protection

Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.

Wide Compatibility & Minimal External Components

Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.

Industrial Temperature Range

Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.

Target Applications

Drone & Embedded System Power Rails

Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.

Industrial & Automotive Electronics

Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.

General-Purpose Point-of-Load Regulation

Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.

Frequently Asked Questions

What is the output voltage of the VIPER22ADIP-E?

Check the specific variant. The VIPER22ADIP-E is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.

What capacitors are needed for stability?

Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics VIPER22ADIP-E with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.

VIPer22ADIP-E: a 60 kHz offline switcher with the MOSFET on the same die, DIP-8

VIPer22ADIP-E is a low power offline switching regulator from STMicroelectronics that puts a current mode PWM controller and a high voltage power MOSFET on one piece of silicon, in a DIP-8 package. It switches at a fixed 60 kHz, runs from a VDD range of 9 V to 38 V, starts itself from a high voltage current source, and protects itself against overtemperature, overcurrent and overvoltage with an auto-restart behaviour. The document covering it is the VIPer22A-E datasheet, which also lists the SO-8 member of the family.

This is the part that turns a rectified mains rail into a low voltage auxiliary supply without a transformer driver stage and without a separate start-up resistor chain. The integrated switch removes the gate drive and the current sense resistor from the bill, and the fixed frequency removes the oscillator components. What it does not remove is the transformer, the snubber and the output diode, which still decide whether the supply meets its efficiency and its EMI limits.

The vendor table, including the power capability

FunctionOffline PWM controller with integrated high voltage MOSFET
Switching frequency60 kHz fixed
VDD operating range9 V to 38 V
ControlCurrent mode with internal high voltage start-up current source
Power capability, DIP-8, European mains20 W at 195 to 265 V AC
Power capability, DIP-8, wide range mains12 W at 85 to 265 V AC
Power capability, SO-8, European mains12 W
Power capability, SO-8, wide range mains7 W
ProtectionsOvertemperature, overcurrent, overvoltage, all with auto-restart
Light load behaviourAutomatic burst mode
UndervoltageAuxiliary undervoltage lockout with hysteresis
PackageDIP-8

The 20 W figure is a thermal statement, not an electrical one

Twenty watts on European mains and twelve on wide range mains is the vendor's own table, and the gap between the two is the point. On a 85 V AC input the primary current for the same output power is roughly twice what it is at 230 V AC, so the conduction loss in the integrated switch and the ripple in the input capacitor both rise. A supply that is quoted at 20 W and then sold into a country with a 110 V supply is a supply that will run hot and fail early, and the fix is either a larger package or a lower output power.

The same reasoning applies to the SO-8 body. It is the same silicon in a smaller package, and the table drops it to 12 W and 7 W for that reason alone. The die does not know which package it is in, and the thermal resistance of the body decides how much of the rating can be used.

Where the part is used and what follows on

Typical loads are battery charger adapters, standby supplies for televisions and monitors, and auxiliary supplies for motor control boards. In SUPERB builds it shows up as the housekeeping rail of an industrial unit that has to start from a wide AC input. Related pages are power management cross reference, obsolete part cross reference hub for the case where a build is moved off an older offline switcher, and one stop BOM sourcing.

Questions buyers ask on this code

Whether the 20 W rating applies to a 110 V market is the first, and it does not: the wide range column is 12 W in the same package. The second is the start-up behaviour, which comes from an internal high voltage current source, so there is no external start-up resistor to select and no bleed path to calculate. The third is the auto-restart on a fault, which means a shorted output will hiccup rather than latch, and a product that needs a latched fault for safety reasons has to add that function outside the part.