VIPER26LDTR
Product Specifications
VIPER26LDTR — Voltage Regulator by STMicroelectronics
The VIPER26LDTR is an STMicroelectronics voltage regulator in SOIC-16_150mil for reliable power management in embedded and industrial applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| VIPER26LDTR | Full Part Number | STMicroelectronics Voltage Regulator |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | VIPER26LDTR |
| Package | SOIC-16_150mil |
| Type | Fixed/Adjustable Voltage Regulator |
| Qualification | Industrial (-40°C to +125°C) |
Product Overview
The VIPER26LDTR is an STMicroelectronics voltage regulator in SOIC-16_150mil package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.
Key Features & Benefits
Stable Output with Built-in Protection
Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.
Wide Compatibility & Minimal External Components
Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.
Industrial Temperature Range
Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.
Target Applications
Drone & Embedded System Power Rails
Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.
Industrial & Automotive Electronics
Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.
General-Purpose Point-of-Load Regulation
Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.
Frequently Asked Questions
What is the output voltage of the VIPER26LDTR?
Check the specific variant. The VIPER26LDTR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.
What capacitors are needed for stability?
Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics VIPER26LDTR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.
VIPER26LDTR: an 800 V offline switcher with a 60 kHz oscillator
VIPER26LDTR is the 60 kHz member of the VIPER26 family in the SO16N body, on tape and reel. It puts an 800 V avalanche rugged power MOSFET, a current mode PWM controller, a high voltage start up current source and an error amplifier on one chip, so an offline flyback or buck can be built with a small external count. The 800 V rating covers a wide mains range and shrinks the drain snubber, which is the part of an offline supply that usually decides the board area.
The L in the code is the low frequency option and the H is the high frequency option. The data sheet prints 54 to 66 kHz for the L type and 115 kHz plus or minus 8 kHz for the H type, and the order code table maps the LD and LDTR strings to the SO16N package with tube and tape and reel packing. That mapping is worth reading before a purchase order is raised, because the LN and HN strings are DIP-7 and the footprint does not interchange.
Figures here come from DS6901 Rev 3, dated October 2020.
The operating window
| Function | Offline current mode PWM controller with integrated power MOSFET |
| Drain source rating | 800 V avalanche rugged |
| Switching frequency | 60 kHz, 54 to 66 kHz over the L type window |
| No load consumption | Below 30 mW at 230 V AC |
| Load consumption | Below 400 mW at 230 V AC with a 250 mW load |
| Start up | Embedded high voltage start up and sense FET |
| Control | Current mode PWM with an embedded error amplifier |
| Current limit | Adjustable set point through the LIM pin |
| Frequency behaviour | Jittered to spread the EMI spectrum |
| Soft start | Built in |
| Protections | Overload and short circuit with auto restart, feedback loop disconnection, hysteretic thermal shutdown |
| Packages in the family | SO16N for the D strings, DIP-7 for the N strings |
The standby arithmetic that sells the part
The two consumption figures in the feature list are the reason this family exists. At 230 V AC with no load the input power stays below 30 mW, and with a 250 mW load it stays below 400 mW, which is an efficiency of about 38 percent at that tiny load. That is not an efficiency number to quote in a datasheet table; it is the number that decides whether a charger or a standby supply meets a standby power regulation. A linear front end with a resistor bleed would burn several hundred milliwatts doing nothing.
Burst mode under light load is what makes the figure possible. The controller skips cycles when the output is above regulation and returns when it falls, and the jitter spreads the resulting spectrum so the EMI filter does not have to be tuned to a single tone. A transformer that works at 60 kHz in continuous mode may need a different snubber for burst operation, and the snubber is usually the first thing to recheck on a prototype.
The 800 V rating matters at the top of the mains window. A 265 V AC input rectifies to about 375 V DC, and the flyback leakage spike adds a margin on top. A 600 V device is marginal in that position and an 800 V device leaves headroom, which is why the family is used across the 85 to 265 V AC range without a different part.
Picking between the L and the H type
At 60 kHz the switching loss is lower and the transformer is larger; at 115 kHz the transformer shrinks and the switching loss rises. For a 5 W to 15 W auxiliary supply the L type is usually the better trade because the transformer is not the limiting component, while for a compact charger the H type earns its place. Both share the same pinout in the same package, so the choice can be made late, but not after the transformer is wound.
Our power management cross reference page lists the offline switchers we compare for these builds, and the one stop BOM sourcing route covers the transformer, the optocoupler and the rest of the primary side on one shipment. Where a build is being consolidated across several product families, the vendor consolidation page describes how we reduce the number of lines without changing the approved parts.
Where the part is used
Auxiliary power supplies for appliances, power metering, LED drivers, set top boxes and recorders are the applications the document names. In practice it appears in any board that needs a few watts from the mains with a low standby budget, including industrial controllers and metering modules that run from a wide mains range.
We supply the string and check the reel and the date code at goods in. For a primary side part the transformer and the creepage distances around the drain node belong to the customer's safety file, and we ask for that file reference before the parts are booked to a line.
Three questions buyers ask about this string
Is the LDTR the 60 kHz version? Yes. The L is the low frequency option, the D is the SO16N body and TR is tape and reel. The HN and LN strings are the DIP-7 parts.
Does it need an auxiliary winding? The embedded high voltage start up source charges the supply pin at power up, and an auxiliary winding takes over in steady state to keep the consumption low. A build without the winding will run, but the no load figure in the feature list will not be met.
Can the current limit be set by the LIM pin? Yes, the set point is adjustable, and that pin is also where a primary current sense resistor connects. Changing the resistor changes the limit, so it belongs in the build documentation rather than in a tuning note.