VNQ7140AJTR
Product Specifications
VNQ7140AJTR — Integrated Motor Driver / Smart Power Switch by STMicroelectronics
The VNQ7140AJTR is an STMicroelectronics integrated motor driver / smart power switch in PowerSSO-16 for automotive and industrial actuator control applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| VNQ7140AJTR | Full Part Number | STMicroelectronics Motor Driver / Power Switch |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | VNQ7140AJTR |
| Package | PowerSSO-16 |
| Type | Integrated Motor Driver / Smart Power Switch |
| Qualification | Automotive AEC-Q100 / Industrial |
Product Overview
The VNQ7140AJTR is an STMicroelectronics integrated motor driver / smart power switch in PowerSSO-16 package. Featuring ST's VIPower technology with monolithic integration of power MOSFETs, gate drivers, and protection/diagnostic circuitry, it simplifies motor control and high-side/low-side switching designs with reduced BOM count and enhanced reliability.
Key Features & Benefits
VIPower Monolithic Integration — Power + Control in One Package
ST's VIPower technology integrates N-channel power MOSFETs, gate drivers, charge pump, and comprehensive protection circuitry on a single die — eliminating external MOSFETs, bootstrap diodes, and sense resistors.
Comprehensive Protection & Diagnostics
Built-in overcurrent, overtemperature (thermal shutdown), undervoltage lockout, and load-dump protection with diagnostic feedback (current sense output, fault status flag) enables self-protecting designs suitable for safety-critical and autonomous systems.
Automotive-Grade Robustness
Designed to withstand harsh automotive and industrial environments including load dump, reverse battery, and extended temperature range for reliable operation in drone payload systems, robotics, and vehicle applications.
Target Applications
Drone Payload & Actuator Control
Drives brushed DC motors, solenoids, and resistive/inductive loads in drone gimbal systems, payload release mechanisms, landing gear actuators, and auxiliary power switching.
Automotive Body & Powertrain
Targets automotive applications including throttle control, EGR valves, HVAC actuators, mirror folding, headlamp leveling, and relay/lamp drivers — all requiring AEC-Q100 qualification.
Industrial Automation & Robotics
Powers motor control, valve actuation, and power distribution in industrial robots, conveyor systems, automated guided vehicles (AGVs), and factory automation equipment.
Frequently Asked Questions
What protection features does the VNQ7140AJTR include?
The VNQ7140AJTR features overcurrent protection, overtemperature shutdown, undervoltage lockout, and diagnostic feedback — ensuring robust, self-protecting operation in demanding environments.
Is external current sensing required?
No. The integrated current-sense output provides proportional load current feedback, eliminating the need for external shunt resistors and differential amplifiers.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics VNQ7140AJTR with full traceability and batch-level QA documentation. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.
VNQ7140AJTR: four high side channels in one PowerSSO-16
VNQ7140AJTR is a quad channel automotive high side driver in the PowerSSO-16 body, on tape and reel. Each channel has 140 milliohm typical on resistance, a 12 A typical current limit in the electrical table and the same protection set as the single channel family: current limitation, overtemperature shutdown with configurable latch off, loss of ground and loss of supply coverage, and reverse battery with external components. The four channels share one supply pin and one multiplexed analog diagnostic pin.
The quad arrangement is the point. Four signal lamps, four small solenoids or a mix of both fit in one package with four independent current readings, which removes three packages and three sets of decoupling from a body control module. The maximum transient supply of 40 V and the 4 V to 28 V operating range put it on the 12 V rail, not on 24 V.
Figures come from the VNQ7140AJ data sheet read this round, which prints 40 V transient, 4 V to 28 V operating, 140 milliohm per channel, 12 A current limit and 0.5 microamp maximum standby current.
The four channels in numbers
| Function | Quad channel high side driver with MultiSense analog feedback |
| Maximum transient supply | 40 V |
| Operating range | 4 V to 28 V |
| On resistance | 140 milliohm typical per channel |
| Current limit | 12 A typical in the electrical table |
| Standby current | 0.5 microamp maximum |
| Logic levels | 3 V and 5 V CMOS compatible |
| Diagnostics | Load current, supply voltage and chip temperature multiplexed on one pin |
| Fault detection | Overload, short to ground, short to supply, off state open load, thermal shutdown |
| Latch behaviour | Configurable latch off with a fault reset pin |
| Supply faults covered | Loss of ground, loss of supply, reverse battery with external components |
| Package | PowerSSO-16 |
| Qualification | Automotive qualified, AEC-Q100 |
Loss per channel and the shared thermal path
At 140 milliohm a 2 A lamp costs 0.56 W in its channel and a 5 A load costs 3.5 W. Four channels at 5 A each would be 14 W in one PowerSSO-16, which no package holds, so the useful case is four loads of 1 A to 2 A, where the total stays between 0.6 W and 2.2 W. The four channels share one die and one thermal path, so the sum matters, not the largest channel.
The diagnostic pin is multiplexed across the four channels, which means the selection logic is part of the current measurement. With four lamps on one package the firmware has to sequence the selections and allow settling time between them, otherwise a reading from one channel is attributed to another. That is the most common bring up issue with this family.
Where the quad driver earns its place
The document names signal lamps up to R10W and LED rear combinations as the intended load. In practice the package is used for rear lamp clusters, interior lighting, small actuators and sensor supply gating, where four independent channels with current feedback save board area. A load with a high inrush, such as an incandescent bulb cold filament, is the case where the 12 A limit and the power limitation behaviour both get exercised.
For a build that mixes a quad driver with single channel devices on the same rail, we check the standby budget as a whole, because four channels at 0.5 microamp maximum plus the rest of the module can exceed a parked vehicle allowance. Our power management cross reference page lists the single and quad strings side by side, and the one stop BOM sourcing route covers the passives and the connectors on the same shipment. Where a customer is reducing the number of approved suppliers, the vendor consolidation page describes how we combine lines without changing approved parts.
Three questions buyers ask about this string
Are the four channels independent? They are independent switches with independent protection, but they share the supply pin, the ground and the thermal path, and the diagnostic pin is multiplexed.
Can one channel drive a motor? It can switch a small motor in one direction, but a bridge is needed for reversal. Four channels can form two bridges if the software handles the cross conduction, and the family that does that internally is a different string.
What happens on a shorted lamp? The channel limits current, heats, and shuts down, and the fault appears on the diagnostic pin. The other three channels keep working, which is what makes the quad package usable in a lamp cluster.