Contact Us

VNS1NV04DPTR-E

Brand: ST
VNS1NV04DPTR-E is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine VNS1NV04DPTR-E with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

VNS1NV04DPTR-E — Integrated Motor Driver / Smart Power Switch by STMicroelectronics

The VNS1NV04DPTR-E is an STMicroelectronics integrated motor driver / smart power switch in SO-8 for automotive and industrial actuator control applications.

Part Number Decoded — Field by Field

FieldValueMeaning
VNS1NV04DPTR-EFull Part NumberSTMicroelectronics Motor Driver / Power Switch

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberVNS1NV04DPTR-E
PackageSO-8
TypeIntegrated Motor Driver / Smart Power Switch
QualificationAutomotive AEC-Q100 / Industrial

Product Overview

The VNS1NV04DPTR-E is an STMicroelectronics integrated motor driver / smart power switch in SO-8 package. Featuring ST's VIPower technology with monolithic integration of power MOSFETs, gate drivers, and protection/diagnostic circuitry, it simplifies motor control and high-side/low-side switching designs with reduced BOM count and enhanced reliability.

Key Features & Benefits

VIPower Monolithic Integration — Power + Control in One Package

ST's VIPower technology integrates N-channel power MOSFETs, gate drivers, charge pump, and comprehensive protection circuitry on a single die — eliminating external MOSFETs, bootstrap diodes, and sense resistors.

Comprehensive Protection & Diagnostics

Built-in overcurrent, overtemperature (thermal shutdown), undervoltage lockout, and load-dump protection with diagnostic feedback (current sense output, fault status flag) enables self-protecting designs suitable for safety-critical and autonomous systems.

Automotive-Grade Robustness

Designed to withstand harsh automotive and industrial environments including load dump, reverse battery, and extended temperature range for reliable operation in drone payload systems, robotics, and vehicle applications.

Target Applications

Drone Payload & Actuator Control

Drives brushed DC motors, solenoids, and resistive/inductive loads in drone gimbal systems, payload release mechanisms, landing gear actuators, and auxiliary power switching.

Automotive Body & Powertrain

Targets automotive applications including throttle control, EGR valves, HVAC actuators, mirror folding, headlamp leveling, and relay/lamp drivers — all requiring AEC-Q100 qualification.

Industrial Automation & Robotics

Powers motor control, valve actuation, and power distribution in industrial robots, conveyor systems, automated guided vehicles (AGVs), and factory automation equipment.

Frequently Asked Questions

What protection features does the VNS1NV04DPTR-E include?

The VNS1NV04DPTR-E features overcurrent protection, overtemperature shutdown, undervoltage lockout, and diagnostic feedback — ensuring robust, self-protecting operation in demanding environments.

Is external current sensing required?

No. The integrated current-sense output provides proportional load current feedback, eliminating the need for external shunt resistors and differential amplifiers.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics VNS1NV04DPTR-E with full traceability and batch-level QA documentation. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.

VNS1NV04DPTR-E: two 250 milliohm OMNIFET switches in one SO-8

VNS1NV04DPTR-E is a dual OMNIFET II device in the SO-8 body, on tape and reel. Each of the two channels is a power MOSFET with a 250 milliohm on resistance, a 1.7 A typical linear current limit and a 40 V drain source clamp, and each channel has its own thermal shutdown and short circuit protection on the same die. The part is meant to replace a plain power MOSFET in a DC to 50 kHz application where the board has no room for a separate driver and protection network.

The gate is brought out directly, so the switch can be driven in the linear region as well as switched. That is unusual and it is the reason the family is used for lamp dimming and for loads that need a soft start, where a plain MOSFET would need an external current sense and a control loop. The clamp is integrated, so an inductive load can be switched off without an external freewheel diode.

Figures come from Doc ID 17344 Rev 3, dated September 2013, and from the device summary table in that document.

The two channels in numbers

FunctionDual fully protected power MOSFET, OMNIFET II, two channels in one body
On resistance250 milliohm maximum per channel
Current limit1.7 A typical, linear limiting
Clamp voltage40 V drain to source
Input currentLow current drawn from the input pin
FeedbackFault reported through the input pin voltage
ProtectionsThermal shutdown, short circuit protection, integrated clamp, ESD protection
Driving modeDirect access to the gate, analog driving possible
Switching useDC up to 50 kHz
CompatibilityPin behaviour compatible with standard power MOSFETs
PackageSO-8, two channels
Order codeVNS1NV04DPTR-E for tape and reel

Loss and clamp behaviour

At 250 milliohm, 1 A costs 0.25 W and the 1.7 A limit costs 0.72 W, so the part is comfortable in the SO-8 body as long as the copper under it is reasonable. The clamp is the figure to watch with an inductive load: when the switch opens, the drain rises until the clamp conducts and the energy in the load is absorbed in the die. A relay with a 1 A coil stores little energy; a solenoid with the same current stores much more, and the clamp has to survive the repetition rate.

Because the limit is linear rather than a hard shutoff, a shorted load pulls the current down to the limit and the die heats until thermal shutdown cycles it. That behaviour is what the family is for, and it also means the part cannot be used as a fast electronic fuse. A load that must be cut in microseconds needs a different device.

Driving the gate in the linear region

Direct gate access makes the part usable as a current sink for a lamp or a heater, with the gate voltage setting the current. The catch is thermal: in linear operation the die dissipates the drop across it, and the SO-8 body has to shed that heat continuously. A lamp dimmer that holds 1 A at half supply puts about 5 W into the package, which is far beyond what the body can hold without a copper plane and an airflow path.

The fault feedback through the input pin is convenient and easy to misread. When the channel shuts down, the input pin behaves differently, and a controller that only reads the pin voltage as a logic level will see a state change without knowing whether it is a fault or a commanded off. The pin to pin cross reference page covers the behaviour comparison we run before a plain MOSFET is replaced by this family.

Supply position and quality paperwork

The family is used in automotive body loads, industrial relay drive and appliance control, and it appears in builds where a customer wants the protection inside the switch rather than around it. Our power management cross reference page lists the neighbouring OMNIFET strings with their resistance and current limit, and the PPAP submission checklist page sets out the paperwork we prepare when the build is automotive and the customer asks for a submission.

We check the reel, the date code and the moisture bag at goods in for every lot of this family, because the SO-8 body is small enough that a mixed reel is hard to spot on the line.

Three questions buyers ask about this string

Is the 250 milliohm figure per channel or for the pair? Per channel. The device summary prints the resistance per each device, and the two channels are independent dice in one package.

Does it need an external flyback diode? Not for the clamp rating, because the 40 V clamp is integrated. An external diode is still worth adding when the load current is high and the clamp energy per cycle would otherwise heat the die.

Can two channels be paralleled for 3.4 A? They can be paralleled, but the current limit of each channel is independent, so the pair does not share evenly during a fault and one channel carries more. For a load above the single channel limit a larger OMNIFET string is the cleaner answer.