Contact Us

LDL1117S33R

Brand: ST
LDL1117S33R is a linear voltage regulator from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine LDL1117S33R with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

LDL1117S33R — Voltage Regulator by STMicroelectronics

The LDL1117S33R is an STMicroelectronics voltage regulator in SOT-223-4 for reliable power management in embedded and industrial applications.

Part Number Decoded — Field by Field

FieldValueMeaning
LDL1117S33RFull Part NumberSTMicroelectronics Voltage Regulator

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberLDL1117S33R
PackageSOT-223-4
TypeFixed/Adjustable Voltage Regulator
QualificationIndustrial (-40°C to +125°C)

Product Overview

The LDL1117S33R is an STMicroelectronics voltage regulator in SOT-223-4 package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.

Key Features & Benefits

Stable Output with Built-in Protection

Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.

Wide Compatibility & Minimal External Components

Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.

Industrial Temperature Range

Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.

Target Applications

Drone & Embedded System Power Rails

Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.

Industrial & Automotive Electronics

Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.

General-Purpose Point-of-Load Regulation

Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.

Frequently Asked Questions

What is the output voltage of the LDL1117S33R?

Check the specific variant. The LDL1117S33R is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.

What capacitors are needed for stability?

Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics LDL1117S33R with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.

LDL1117S33R: 1.2 A at 3.3 V with 350 mV of dropout and 87 dB of rejection

LDL1117S33R is the fixed 3.3 V member of the LDL1117 family from STMicroelectronics, in the SOT-223 body. It guarantees 1.2 A of output current, takes an input from 2.5 V to 18 V with a 20 V absolute maximum, and has a typical dropout of 350 mV at the full 1.2 A. The supply rejection is 87 dB at 120 Hz and stays above 40 dB out to 100 kHz, which is the figure that makes this part a post regulator rather than a bulk supply. The document is DS12022, revision 7, dated January 2021.

The 350 mV dropout is the headline. A 3.3 V output needs only about 3.65 V at the input to hold regulation at 1.2 A, so a 5 V rail with a 5 percent tolerance still leaves well over a volt of margin at the worst case. That is a different starting point from the LD1117, which needs 1 V and therefore more headroom at the same current, and from the 78 series parts, which need 2 V.

Data from the vendor document

Output voltage3.3 V fixed, part of a family covering 1.2, 1.5, 1.8, 2.5, 3.0 and 5.0 V
Output current1.2 A guaranteed
Dropout voltage350 mV typical at 1.2 A
Input voltage range2.5 V to 18 V
Absolute maximum input20 V
Supply rejection87 dB at 120 Hz, above 40 dB at 100 kHz
ProtectionsThermal, current and power limitation, safe operating area
Operating temperatureminus 40 to plus 125 degrees
PackageSOT-223
Named applicationsSMPS post regulation, DC to DC post regulation, motherboard point of load, industrial and consumer

Heat at 1.2 A and why the rejection figure matters

At 1.2 A with 400 mV of headroom the part dissipates 480 mW, which a SOT-223 with a copper tab will hold at a moderate ambient. At 1.2 A from a 5 V rail to a 3.3 V output the dissipation is 2.04 W, and that is beyond what the body can do without a serious copper island and airflow. The part makes a 3.3 V rail from a supply that is already close to 3.3 V, and it makes it badly from a 5 V rail at full current. This is the single most common mistake on this family.

The rejection curve is the other reason to choose it. A switching regulator ahead of this part leaves ripple at its own switching frequency, and 87 dB at 120 Hz plus more than 40 dB at 100 kHz means the ripple that survives is small enough for an analogue front end. A part with 60 dB of rejection would leave ten times more of it on the rail, which on a receive chain is the difference between a quiet floor and a visible spur.

Where it fits and the related pages

Typical uses are point of load regulation on a motherboard, post regulation behind an AC to DC switcher, and the analogue rail of an instrument. In SUPERB builds it appears on the supply side of RF and medical boards where the switcher has to sit away from the sensitive section. Related pages are power management cross reference, one stop BOM sourcing, and component lead time solutions.

Questions buyers ask on this code

The first is whether 350 mV of dropout is real at 1.2 A, and the vendor states it as typical at that current, so a build that depends on it should leave margin for the maximum rather than the typical. The second is the input range, and 18 V is the operating ceiling with 20 V as the absolute maximum, which rules out a 24 V industrial rail. The third is whether the SOT-223 will hold 1.2 A, and the answer depends entirely on the copper under the tab and the ambient, not on the part rating.