Contact Us

CD4070BM96

Brand: Texas Instruments
Texas Instruments CD4070BM96 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4070BM96 — Power Management & Signal Chain | Superb Automation

CD4070BM96

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4070BM96 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4070BM96: the quad exclusive-OR gate on a 2500 piece SOIC reel

The CD4070BM96 is the large tape and reel entry for the CD4070B, four independent exclusive-OR gates with two inputs each, in a 14-lead small outline body. The vendor page lists the device as ACTIVE with the descriptor 4-ch, 2-input, 3-V to 18-V XOR gates, a drive of 6.8 mA in both directions, an 8 Mbps data rate and an operating range of minus 55 to plus 125 degrees. The reel row is 2500 pieces, level 1 at 260 degrees, nickel palladium gold finish, and the marking on the body is CD4070BM rather than the orderable string.

The same document carries the CD4077B, which is the exclusive-NOR member of the pair, and that is the source of most of the confusion around this part. A buyer who needs an XOR and orders a 4077 gets the inverted function and a board that passes continuity but fails a truth table. Both parts sit on one addendum, both have the same 14-lead bodies, and the only difference at the orderable level is the digit in the middle of the string.

The CD4070B rows as the addendum publishes them

Part classFour independent two input exclusive-OR gates
Vendor descriptor4-ch, 2-input, 3-V to 18-V XOR gates
Vendor statusACTIVE, catalogue rating
Data sheetSCHS052 or later revision, document acquired from Harris Semiconductor
Package addendum date18 September 2026
Supply range3 V to 18 V, 20 V type rating in the headline
Output drive6.8 mA sink and source at 15 V
Data rate8 Mbps in the parametric table
Propagation delay65 ns typical at 10 V into 50 pF
Input current1 microamp at 18 V over temperature, 100 nA at 25 degrees
Noise margin1 V at 5 V, 2 V at 10 V, 2.5 V at 15 V
Thermal, PDIP80 degrees per watt junction to ambient
Thermal, SOIC86 degrees per watt junction to ambient
Thermal, SOP and TSSOP76 and 113 degrees per watt
SOIC body14 leads, 51.9 square millimetres, 8.65 by 6 mm
SOIC tube rowCD4070BM, Obsolete, blank quantity, Call TI
SOIC reel rowCD4070BM96, 2500 pieces, large tape and reel, Active
Other SOIC rowsCD4070BMT Obsolete, CD4070BM96E4 Active
SOP reel rowCD4070BNSR, 2000 pieces, Active
TSSOP rowsCD4070BPW tube Obsolete, CD4070BPWR reel 2000 Active
PDIP rowCD4070BE, 25 pieces in a tube, Active
Ceramic rowsCD4070BF and CD4070BF3A, 25 pieces each, Active

The tube row being closed is the fact that changes a small build. A customer who needs thirty pieces for a pilot cannot buy a tube, because the only live SOIC format is the 2500 piece reel. The choice is a partial reel, a move to the SOP reel at 2000 pieces, or a move to the plastic DIP at 25 pieces. Each of those is a different footprint, and the DIP is 181.42 square millimetres against 51.9 for the SOIC, so the board does not accept the substitution without a change to the copper and to the solder process.

What the parametric table fixes

The gate is specified over 3 to 18 V with parametric ratings at 5, 10 and 15 V, a drive of 6.8 mA and a data rate of 8 Mbps. Propagation is 65 ns typical at 10 V into 50 pF, which is slower than the 60 ns of the OR and AND gates in the same family and slower than the 30 ns of the unbuffered inverter, and that difference is a property of the exclusive-OR structure rather than a process spread. A chain of four XOR stages at 10 V therefore adds about 260 ns of typical delay before wiring capacitance is counted, which is why parity logic built from this part runs at a few megahertz rather than at tens of megahertz.

The input current is 1 microamp at 18 V over the full temperature range and 100 nA at 18 V and 25 degrees. That number matters when the gate is driven from a high value resistor or from a capacitive divider, because a microamp into a 1 megohm node is a volt of error. The noise margin of 1 V at 5 V, 2 V at 10 V and 2.5 V at 15 V is the other figure to check on a mixed rail board, and it is quoted for the full package temperature range rather than at 25 degrees only.

The 20 V headline and the 18 V operating limit are not the same statement. The absolute maximum supply is half a volt above 20 V, the parametric table stops at 15 V, and the product page stops at 18 V. A board that runs the gate at 18 V has DC limits from the data sheet but no guaranteed switching limit, so the page reports the gap rather than smoothing it into a single range.

Where the small outline body fits

The 14-lead SOIC is the middle of four body options in area terms. The plastic DIP is 181.42 square millimetres, the SOP is 79.56, the SOIC is 51.9 and the TSSOP is 32. The SOIC is the body that fits a reflow line and still has a 1.27 mm lead pitch, which is the pitch most contract assembly houses can place without an X-ray check. The TSSOP halves the area again but moves to a 0.65 mm pitch, and on a two layer board with a wide ground pour that pitch is where solder bridging starts.

Thermal impedance is 86 degrees per watt in the SOIC against 80 in the plastic DIP and 113 in the TSSOP. At static currents the number is irrelevant, and at 6.8 mA into a 15 V rail with all four gates switching it is still small. The case where it matters is a fault: an output shorted to a rail through a low impedance load will heat the die until the package limit is reached, and the TSSOP reaches that limit first. A customer who expects a fault condition on the bench should be told that the wider body has more margin.

What the documents do not publish

The page prints a typical propagation delay and no maximum, a data rate that is a parametric table entry rather than a measured curve, and no output capacitance or short circuit current. The full switching table with 5 V, 10 V and 15 V columns is in the data sheet, which is a text document rather than a scan, so the numbers can be read directly, but they are not on the page. The page also does not print the truth table, and for an exclusive-OR that is the first thing a test engineer asks for. It omits the input threshold spread across the three rails as well.

Second source and long term availability

The CD4070B is a second sourced part under the same number from more than one vendor, and the 14-lead pin out has been stable for decades. The substitution that looks safe and is not is a move to a 74HC86, because the input threshold and the drive change at 5 V and the propagation delay drops by an order of magnitude, which can turn a deliberately slow parity chain into a race. The obsolete part cross reference hub collects the checks we run before naming a candidate, and the how to verify a drop in replacement page covers the bench work.

What to send with an enquiry

Send the exact string, the function you need, the body, the quantity and the date. If the board is already released with the tube row on it, say so, because that row is closed and the alternatives are a partial reel or a body change. The BOM scrubbing page covers how the orderable rows are reconciled before a quote is issued.