Contact Us

L5973D013TR

Brand: ST
L5973D013TR is a switching regulator IC from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine L5973D013TR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

L5973D013TR — Voltage Regulator by STMicroelectronics

The L5973D013TR is an STMicroelectronics voltage regulator in HSOP-8 for reliable power management in embedded and industrial applications.

Part Number Decoded — Field by Field

FieldValueMeaning
L5973D013TRFull Part NumberSTMicroelectronics Voltage Regulator

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberL5973D013TR
PackageHSOP-8
TypeFixed/Adjustable Voltage Regulator
QualificationIndustrial (-40°C to +125°C)

Product Overview

The L5973D013TR is an STMicroelectronics voltage regulator in HSOP-8 package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.

Key Features & Benefits

Stable Output with Built-in Protection

Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.

Wide Compatibility & Minimal External Components

Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.

Industrial Temperature Range

Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.

Target Applications

Drone & Embedded System Power Rails

Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.

Industrial & Automotive Electronics

Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.

General-Purpose Point-of-Load Regulation

Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.

Frequently Asked Questions

What is the output voltage of the L5973D013TR?

Check the specific variant. The L5973D013TR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.

What capacitors are needed for stability?

Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics L5973D013TR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.

L5973D013TR: a 2.5 A step down regulator from 4 V to 36 V at 250 kHz

L5973D013TR is a monolithic step down switching regulator from STMicroelectronics in the HSOP8 body with an exposed pad, tape and reel. It has a 2.5 A internal switch, takes an input from 4 V to 36 V, sets the output anywhere from 1.235 V to 35 V with two resistors, and runs at a fixed 250 kHz. The exposed frame drops the junction to ambient resistance to about 40 degrees per watt, which is what makes 2 A of DC load realistic in a small body.

The switch is a P channel DMOS device with a typical on resistance of 250 milliohms, and the controller allows 100 percent duty cycle, so the part behaves like a linear regulator at low headroom instead of dropping out. That combination is why it appears on 5 V and 12 V buses in printers, disk drives, set top boxes and industrial controllers, where the input can fall close to the output during a transient.

The figures a buyer checks

FunctionMonolithic step down switching regulator
Switch current2.5 A minimum switch current limit
Input voltage4 V to 36 V
Output voltageAdjustable from 1.235 V to 35 V
Reference3.3 V nominal with 2 percent accuracy, divided down for the output setting
Switching frequency250 kHz internally fixed
Switch on resistance250 milliohms typical, P channel DMOS
Duty cycleUp to 100 percent, low dropout operation
Junction to ambientAbout 40 degrees per watt on the exposed frame
ProtectionsInternal current limit, thermal shutdown, feedback disconnection
Other functionsVoltage feedforward, zero load current operation, inhibit, synchronisation
PackageHSOP8 with exposed pad

Working the numbers at 12 V in and 5 V out

At 2 A output and 5 V, the load takes 10 W. With an efficiency around 85 percent the part dissipates roughly 1.7 W, of which the switch conduction loss at 250 milliohms and a 40 percent duty cycle is about 0.4 W and the rest belongs to the diode and the inductor. On an exposed pad at 40 degrees per watt the junction sits about 68 degrees above ambient, which is inside the range in a 25 degree room and marginal at 60 degrees. The practical ceiling for this body is nearer 1.5 A than 2 A once the ambient is honest.

The 250 kHz frequency is a compromise the vendor made for the package. It keeps the switching loss low enough for a body this size, and it allows an inductor of a few microhenries rather than a few tens. A board that needs a smaller inductor or a lower output ripple has to go to a family that switches faster, and that family will have a higher switching loss in exchange.

Where it sits and the pages that follow

Typical uses are point of load rails in printers, disk drives, set top boxes and industrial controllers, and 5 V or 3.3 V rails from a 12 V or 24 V bus. Related pages are power management cross reference, pin to pin cross reference for the step down families that share the pinout, and one stop BOM sourcing.

Questions buyers ask on this code

Whether 2.5 A means the load can be 2.5 A is the first, and it does not: the figure is a minimum switch current limit, and the load depends on the duty cycle, the inductor and the thermal path. The second is the input range, which starts at 4 V and makes the part usable on a 5 V bus with a 3.3 V output only in low dropout mode, where it behaves as a pass element and the losses move into the package. The third is the exposed pad, which has to be soldered to a copper area with vias, because without it the 40 degrees per watt figure does not apply.