VNS3NV04DPTR-E
Product Specifications
VNS3NV04DPTR-E — Integrated Motor Driver / Smart Power Switch by STMicroelectronics
The VNS3NV04DPTR-E is an STMicroelectronics integrated motor driver / smart power switch in SO-8 for automotive and industrial actuator control applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| VNS3NV04DPTR-E | Full Part Number | STMicroelectronics Motor Driver / Power Switch |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | VNS3NV04DPTR-E |
| Package | SO-8 |
| Type | Integrated Motor Driver / Smart Power Switch |
| Qualification | Automotive AEC-Q100 / Industrial |
Product Overview
The VNS3NV04DPTR-E is an STMicroelectronics integrated motor driver / smart power switch in SO-8 package. Featuring ST's VIPower technology with monolithic integration of power MOSFETs, gate drivers, and protection/diagnostic circuitry, it simplifies motor control and high-side/low-side switching designs with reduced BOM count and enhanced reliability.
Key Features & Benefits
VIPower Monolithic Integration — Power + Control in One Package
ST's VIPower technology integrates N-channel power MOSFETs, gate drivers, charge pump, and comprehensive protection circuitry on a single die — eliminating external MOSFETs, bootstrap diodes, and sense resistors.
Comprehensive Protection & Diagnostics
Built-in overcurrent, overtemperature (thermal shutdown), undervoltage lockout, and load-dump protection with diagnostic feedback (current sense output, fault status flag) enables self-protecting designs suitable for safety-critical and autonomous systems.
Automotive-Grade Robustness
Designed to withstand harsh automotive and industrial environments including load dump, reverse battery, and extended temperature range for reliable operation in drone payload systems, robotics, and vehicle applications.
Target Applications
Drone Payload & Actuator Control
Drives brushed DC motors, solenoids, and resistive/inductive loads in drone gimbal systems, payload release mechanisms, landing gear actuators, and auxiliary power switching.
Automotive Body & Powertrain
Targets automotive applications including throttle control, EGR valves, HVAC actuators, mirror folding, headlamp leveling, and relay/lamp drivers — all requiring AEC-Q100 qualification.
Industrial Automation & Robotics
Powers motor control, valve actuation, and power distribution in industrial robots, conveyor systems, automated guided vehicles (AGVs), and factory automation equipment.
Frequently Asked Questions
What protection features does the VNS3NV04DPTR-E include?
The VNS3NV04DPTR-E features overcurrent protection, overtemperature shutdown, undervoltage lockout, and diagnostic feedback — ensuring robust, self-protecting operation in demanding environments.
Is external current sensing required?
No. The integrated current-sense output provides proportional load current feedback, eliminating the need for external shunt resistors and differential amplifiers.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics VNS3NV04DPTR-E with full traceability and batch-level QA documentation. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.
VNS3NV04DPTR-E: two 120 milliohm OMNIFET channels for DC-13 loads
VNS3NV04DPTR-E is a dual OMNIFET II device in the SO-8 body, on tape and reel, with 120 milliohm on resistance per channel, a 3.5 A typical linear current limit and a 40 V drain source clamp. It is AEC-Q100 qualified and ECOPACK marked, and the data sheet names DC-13 loads to EN 60947-5-1 as a target duty, which is the contactor coil class in industrial control.
The family replaces a plain power MOSFET plus its gate drive and protection network with one protected switch. Each channel has thermal shutdown, short circuit protection and an integrated clamp, and the fault is reported back through the input pin, so the controller can tell a fault from a commanded off without a separate diagnostic line.
Figures come from the VNS3NV04DP-E data sheet read this round.
The two channels in numbers
| Function | Dual fully protected power MOSFET, OMNIFET II |
| On resistance | 120 milliohm maximum per channel |
| Current limit | 3.5 A typical, linear |
| Clamp voltage | 40 V drain to source |
| Loads named in the document | Resistive, capacitive and inductive, including DC-13 contactor coils |
| Fault feedback | Through the input pin voltage |
| Protections | Thermal shutdown, short circuit, integrated clamp, ESD |
| Driving mode | Direct gate access, analog driving possible |
| Switching use | DC up to 50 kHz |
| Qualification | AEC-Q100 |
| Marking | ECOPACK, lead free and RoHS compliant |
| Package | SO-8, two channels |
Loss, clamp energy and the coil load
At 120 milliohm, 2 A costs 0.48 W per channel and the 3.5 A limit costs 1.47 W, which the SO-8 body can hold with reasonable copper. The clamp takes the inductive energy at turn off: a contactor coil that draws 1 A and holds a few hundred millijoules will put that energy into the die on every release, and the repetition rate decides whether the clamp temperature stays inside the limit.
That is the difference between switching a relay coil once a minute and switching a valve coil at 20 Hz. The first is a comfortable application; the second needs the clamp energy per cycle multiplied by the frequency and compared with what the package can shed. A freewheel diode across the coil moves most of that energy out of the die, at the cost of a slower release.
The linear region and the thermal consequence
The gate is accessible, so the channel can be used as a current limiter in series with a load. In that mode the die dissipates the voltage across it, and 2 A at a 3 V drop is 6 W in an SO-8 body, which is far outside steady state capability without a copper plane and airflow. The linear mode is a transient tool, not a continuous operating point.
The input pin doubles as the fault output, and the behaviour differs between a commanded off and a protection event. A controller that reads the pin as a plain logic level will see a state change without knowing the cause, which is why the first article test for this family includes a deliberate short on one channel and a check that the other channel keeps working.
Supply position and checks
The part is used in industrial control, automotive body loads and appliance drive, where a protected switch in a small body removes several discrete parts from the board. Our power management cross reference page lists the OMNIFET strings by resistance and current limit so the choice between the 120 milliohm and 250 milliohm channels is made on arithmetic rather than on availability. For automotive builds the PPAP submission checklist page covers the submission we prepare, and the pin to pin cross reference page describes the comparison we run before a plain MOSFET is replaced.
Three questions buyers ask about this string
Is the 3.5 A figure a continuous current? It is the typical linear current limit. Continuous current is set by the package thermals, and at 120 milliohm the loss at 2 A is under half a watt per channel.
Can both channels be used in parallel? They can, but the limits are independent and one channel takes more during a fault. For a load above the single channel limit a bigger string is cleaner.
Does it replace a relay? It replaces the coil driver, not the relay. Where the load is a contactor coil this family is a direct fit, and where the load is the contactor contact a different device class applies.