CD4051BM96
Product Specifications
CD4051BM96
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4051BM96 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4051BM96: the 8 to 1 multiplexer on a 2500 piece SOIC reel
The CD4051BM96 is the small outline reel member of the CD4051B family and the row that most surface mount production lines actually buy. The part is a single 8 channel analogue multiplexer with on-chip binary address decoding and logic level conversion, described by the vendor as a 20 V, 8 to 1, single channel analogue multiplexer and marked ACTIVE. The parametric table gives a typical on resistance of 125 ohms, a bandwidth of 20 MHz, an on capacitance of 30 picofarads, a maximum on state leakage of 0.3 microamps, a typical supply current of 0.04 microamps and a 10 milliamp continuous channel current.
The row itself is straightforward: Active, SOIC body with 16 leads, 2500 pieces on a large tape and reel, RoHS yes, nickel palladium gold finish, moisture level 1 at 260 degrees with unlimited floor life, operating range minus 55 to plus 125 degrees, and the marking CD4051BM on the body. The .A row beside it carries the same quantity and the same marking, and the obsolete rows BMT, BM96G3 and BM96G4 show that this reel is the only surviving SOIC format in the family.
The CD4051BM96 row as the vendor addendum publishes it
| Part class | Single 8 channel analogue multiplexer and demultiplexer |
| Vendor document | SCHS047O, revised May 2026, CD4051B, CD4052B and CD4053B |
| Package addendum date | 26 September 2026 |
| Package for this code | SOIC (D), 16 leads, 59.4 square millimetres at 9.9 by 6 mm |
| Packing | 2500 pieces on a large tape and reel |
| Status | Active, production |
| RoHS | Yes |
| Lead finish | NIPDAU |
| Moisture level | Level 1 at 260 degrees, unlimited floor life |
| Part marking | CD4051BM |
| Sibling row | CD4051BM96.A, same body, quantity and marking |
| Obsolete SOIC rows | CD4051BMT, CD4051BM96G3, CD4051BM96G4 |
| TSSOP reel row | CD4051BPWR, 2000 pieces, marking CM051B |
| SOP reel row | CD4051BNSR, 2000 pieces |
| PDIP row | CD4051BE, 25 pieces in a tube |
| Configuration | 8 to 1, one channel, bidirectional |
| Analogue range | Up to 20 V peak to peak, single supply 3 V to 20 V |
| Digital range | 3 V to 20 V, independent of the analogue rails |
| On resistance | 125 ohms typical at 15 V |
| Leakage | Plus or minus 10 pA typical, 0.3 microamps maximum |
| Bandwidth | 20 MHz |
| Switching | Break before make |
What a 2500 piece reel commits a build to
A full reel of 2500 pieces suits a build of 2000 with a 500 piece attrition allowance, or two builds of 1200 with a small remnant. It does not suit a build of 150. On a high mix line the reel becomes a kitting decision rather than a purchasing one: either the line keeps the reel as a stock item and draws from it across builds, or it takes a cut reel with a printed label and a sealed bag, which most contract assemblers will accept if the label carries the quantity, the date code and the moisture indicator.
Moisture level 1 with unlimited floor life is the property that makes the second option practical. A level 3 part has to be baked after a shift out of the bag and resealed with a desiccant, which costs a day. A level 1 part can sit on the feeder overnight and go back on the shelf. On a board that is scheduled in small batches, that difference is worth more than the piece price difference between the SOIC and TSSOP bodies.
Signal behaviour at the switch
One hundred and twenty five ohms of on resistance at 15 V is the vendor's typical figure over the input range, and it is not a constant. A signal source with a 10 kilohm output impedance driving a 1 megohm load sees the switch resistance as a 1.25 per cent gain error at worst, which is acceptable for a monitoring channel and not acceptable for a precision attenuator. The same part switching into a high impedance amplifier input sees no error at all because the input draws picoamps.
The 20 MHz bandwidth is a small signal figure and the 30 picofarad on capacitance is what limits the settling time on a high impedance node. A 30 picofarad channel capacitance against a 1 megohm source is a 5 microsecond time constant, so an eight channel scan that needs full settling runs at tens of kilohertz rather than hundreds. A data logger that multiplexes thermocouples sees no problem; a board that multiplexes a video signal is using the wrong part.
Break before make and the address change
The vendor lists break before make as a device feature, which matters when two channels carry different sources that must never be connected. During an address change the part opens the present channel before it closes the next, so the common pin is briefly floating. On a high impedance node that floating interval lets the pin drift, and the acquisition circuit has to allow for it. On a low impedance node the interval is invisible.
That interval is also why the part is not suitable as a protection switch: a break before make sequence that is measured in nanoseconds still leaves a gap, and a gap on a power rail is a reset. The right part for that job is a load switch with a controlled ramp, not an analogue multiplexer.
The family also carries an inhibit input that turns every channel off while leaving the address decoding intact. That pin is what allows a bank of multiplexers to be parked during a conversion so an unselected channel cannot inject charge into a shared common line, and it is the reason a scan can be sequenced rather than left free running. It does not disconnect the common pin from the outside world, so a board that needs true isolation still needs a series switch.
Supply and control details worth checking before the first build
The digital inputs are specified from 3 V to 20 V regardless of the analogue supply, which means a 3.3 V microcontroller can drive an address pin on a part running plus or minus 10 V without a translator. It also means a 20 V logic swing on the control pin is allowed, and that is unusual enough to be worth planning for deliberately rather than by accident. Input current is not specified in the parametric summary this page quotes, so a customer who needs a pull-up value should read the switching table in the document rather than assume.
Single supply operation below 3 V is outside the vendor's performance claim, and the family's lowest published single supply option is 3.3 V. A 3.0 V rail is inside the 3 V to 20 V range in the feature list but the vendor notes that performance degrades below 3 V, so a 3.0 V board sits on the edge. Boards running at 2.5 V need a different switch rather than this one at a lower address.
Where the reel row sits in the sourcing picture
Because the SOIC tube row no longer exists, this reel is the only way to keep a 16-lead SOIC footprint supplied, and that makes it the row to plan around for long life products. A final order sized against remaining build life rather than the next twelve months is the standard answer, and the last time buy and LTB planning page sets out how that quantity is calculated. The date code management page covers how a stock of final buy reels is rotated so the oldest reel is used first.
Where a second source is needed rather than a final buy, the vendor's own TMUX4051 is listed as a drop-in replacement with upgraded functionality, at plus or minus 12 V and 1.8 V logic. The pin to pin cross reference page covers the comparison, and the note to carry into any review is that the analogue rail range is narrower on the replacement than on the original.