Contact Us

VND14NV04TR-E

Brand: ST
VND14NV04TR-E is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine VND14NV04TR-E with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

VND14NV04TR-E — Integrated Motor Driver / Smart Power Switch by STMicroelectronics

The VND14NV04TR-E is an STMicroelectronics integrated motor driver / smart power switch in DPAK for automotive and industrial actuator control applications.

Part Number Decoded — Field by Field

FieldValueMeaning
VND14NV04TR-EFull Part NumberSTMicroelectronics Motor Driver / Power Switch

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberVND14NV04TR-E
PackageDPAK
TypeIntegrated Motor Driver / Smart Power Switch
QualificationAutomotive AEC-Q100 / Industrial

Product Overview

The VND14NV04TR-E is an STMicroelectronics integrated motor driver / smart power switch in DPAK package. Featuring ST's VIPower technology with monolithic integration of power MOSFETs, gate drivers, and protection/diagnostic circuitry, it simplifies motor control and high-side/low-side switching designs with reduced BOM count and enhanced reliability.

Key Features & Benefits

VIPower Monolithic Integration — Power + Control in One Package

ST's VIPower technology integrates N-channel power MOSFETs, gate drivers, charge pump, and comprehensive protection circuitry on a single die — eliminating external MOSFETs, bootstrap diodes, and sense resistors.

Comprehensive Protection & Diagnostics

Built-in overcurrent, overtemperature (thermal shutdown), undervoltage lockout, and load-dump protection with diagnostic feedback (current sense output, fault status flag) enables self-protecting designs suitable for safety-critical and autonomous systems.

Automotive-Grade Robustness

Designed to withstand harsh automotive and industrial environments including load dump, reverse battery, and extended temperature range for reliable operation in drone payload systems, robotics, and vehicle applications.

Target Applications

Drone Payload & Actuator Control

Drives brushed DC motors, solenoids, and resistive/inductive loads in drone gimbal systems, payload release mechanisms, landing gear actuators, and auxiliary power switching.

Automotive Body & Powertrain

Targets automotive applications including throttle control, EGR valves, HVAC actuators, mirror folding, headlamp leveling, and relay/lamp drivers — all requiring AEC-Q100 qualification.

Industrial Automation & Robotics

Powers motor control, valve actuation, and power distribution in industrial robots, conveyor systems, automated guided vehicles (AGVs), and factory automation equipment.

Frequently Asked Questions

What protection features does the VND14NV04TR-E include?

The VND14NV04TR-E features overcurrent protection, overtemperature shutdown, undervoltage lockout, and diagnostic feedback — ensuring robust, self-protecting operation in demanding environments.

Is external current sensing required?

No. The integrated current-sense output provides proportional load current feedback, eliminating the need for external shunt resistors and differential amplifiers.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics VND14NV04TR-E with full traceability and batch-level QA documentation. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.

VND14NV04TR-E: a 35 milliohm OMNIFET in the DPAK body

VND14NV04TR-E is a single OMNIFET II fully protected power MOSFET in the DPAK body, on tape and reel. It holds 35 milliohm on resistance, a 12 A typical current limit and a 40 V clamp, and it brings the OMNIFET protection set into a package that can be bolted to a copper area: thermal shutdown, linear current limitation, short circuit protection and an integrated clamp.

The DPAK body is the reason to choose this string over the SO-8 members of the same family. The tab carries heat into the board far better than a small outline body, so the same die can hold several times the continuous current. For a load between 5 A and 10 A the DPAK version is the one that survives, and the SO-8 versions are for loads under 2 A.

Figures come from the VNB14NV04 and VND14NV04 data sheet read this round, which prints 35 milliohm, 12 A current limit and a 40 V clamp for the family, and lists the D package as the DPAK body.

The switch in numbers

FunctionSingle fully protected power MOSFET, OMNIFET II, low side
On resistance35 milliohm
Current limit12 A typical, linear
Clamp voltage40 V drain to source
ProtectionsThermal shutdown, short circuit, integrated clamp, ESD
Fault feedbackThrough the input pin voltage
Driving modeDirect gate access, analog driving possible
Switching useDC up to 50 kHz
CompatibilityBehaviour compatible with standard power MOSFETs
PackageDPAK, tab down for board cooling
PackingTape and reel for the TR string

Loss and the tab

At 35 milliohm, 5 A costs 0.875 W and 10 A costs 3.5 W. The DPAK tab soldered to a copper island spreads that loss, and the copper area under the tab is the component that decides whether 10 A is continuous or a short burst. A tab left floating on a narrow trace turns a 3.5 W load into a hot spot within a few minutes of running.

The linear current limit is the behaviour that separates this family from a plain MOSFET. Under a short the channel pulls the current down to the limit and heats, then thermal shutdown cycles it until the fault clears. That is deliberate behaviour of the part, and it means the switch cannot be used as a fast fuse. For a load that must be cut immediately, a different device class applies.

Where a DPAK OMNIFET fits

Relay and solenoid drive at several amps, lamp switching, heater control and small motor drive in one direction, on 12 V and 24 V rails within the 40 V clamp. The family is used in automotive body modules, industrial control and appliance power boards, wherever the protection has to live inside the switch.

The gate access makes the part usable as a linear current sink, and that mode is limited by the package rather than by the die. A DPAK can hold a few watts on a good copper island; it cannot hold ten watts in still air.

We supply the string and compare it against the other OMNIFET bodies when a customer needs a different current or a smaller footprint. The power management cross reference page lists the family by resistance and package, the pin to pin cross reference page covers the pinout comparison before a substitution, and the one stop BOM sourcing route covers the passives and connectors on the same shipment.

Three questions buyers ask about this string

Is the current limit 12 A continuous? It is the typical linear limit under a fault. Continuous current is set by the 35 milliohm loss and the copper under the tab.

Can the tab be left unconnected to a plane? It can be soldered to a small pad for mechanical reasons, but then the thermal path is the die to the package only, and the continuous current drops sharply.

Does it need an external diode for a relay coil? The clamp handles the kick, and an external diode is still useful where the coil stores a lot of energy and switches often.