CD4047BE
Product Specifications
CD4047BE
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4047BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4047BE: the monostable and astable multivibrator in the 14-lead plastic DIP
The CD4047BE is the plastic dual in line member of the CD4047B family, a CMOS multivibrator that works as a one shot or as a free running oscillator with one external resistor and one external capacitor. The vendor describes the family as a CMOS low power monostable and astable multivibrator and marks it ACTIVE. The parametric table gives one channel, standard CMOS input, push pull output, 600 microamps of supply current, 4 milliamps of sink current and 4 milliamps of source current, with an operating range of minus 55 to plus 125 degrees.
The E suffix is what this row is about. The package option addendum dated 18 September 2026 lists CD4047BE as Active and in production, 25 pieces to a tube, RoHS yes with a nickel palladium gold lead finish, no moisture sensitivity level because a through-hole body is not reflow classified, and the marking CD4047BE. The same addendum carries CD4047BE.A and CD4047BEE4 on the same 25 piece tube, so a vendor list that shows three rows for one string is normal rather than an error, and the body marking is identical across all three rows.
The CD4047BE row as the vendor addendum publishes it
| Part class | CMOS low power monostable and astable multivibrator |
| Vendor document | SCHS044C, revised September 2003, acquired from Harris Semiconductor |
| Supply range | 3 V to 18 V, with 5 V, 10 V and 15 V parametric ratings |
| Channels | One, with true and complemented buffered outputs |
| Output drive | 4 mA sink and 4 mA source at the rated conditions |
| Supply current | 600 microamps maximum, quiescent current tested at 20 V on every unit |
| External parts | One resistor and one capacitor set the pulse width or the frequency |
| Monostable features | Positive or negative edge trigger, pulse width independent of trigger width |
| Retrigger | Retriggerable option for pulse width expansion |
| Power on | Internal power on reset circuit |
| Astable features | Free running or gatable, 50 per cent duty cycle, oscillator output available |
| Frequency stability | Plus or minus 2 per cent plus 0.03 per cent per degree at 100 kHz |
| Trimmed stability | Plus or minus 0.5 per cent plus 0.015 per cent per degree at 10 kHz |
| Package for this code | PDIP (N), 14 leads, 181.42 square millimetres |
| Packing | 25 pieces in a tube |
| Lead finish | NIPDAU |
| Moisture level | Not applicable for this package type |
| Status | Active, production |
| Part marking | CD4047BE |
| Same string in the addendum | CD4047BE.A and CD4047BEE4, both 25 piece tube |
| Surface mount rows | CD4047BM96 2500 piece reel, CD4047BNSR 2000 piece reel, CD4047BPWR 2000 piece reel |
| Obsolete rows of the family | CD4047BM, CD4047BMT and CD4047BPW, quantity blank, Call TI |
Two modes from one die and one RC pair
In monostable mode the part produces a pulse whose width is set by the external resistor and capacitor and does not follow the width of the trigger. The vendor lists a positive or negative edge trigger, a retriggerable option that extends the pulse, and an internal power on reset that keeps the output defined while the supply comes up. Recovery time is quoted as essentially independent of pulse width and the pulse width accuracy holds at duty cycles approaching 100 per cent, which is the property that makes the part usable as a missing pulse detector as well as a one shot.
In astable mode the same two passive parts set a free running frequency at a 50 per cent duty cycle, with the oscillator output available on a separate pin and the oscillation gateable through the ASTABLE pin. The vendor gives two accuracy windows rather than one: plus or minus 2 per cent plus 0.03 per cent per degree at 100 kHz, and plus or minus 0.5 per cent plus 0.015 per cent per degree at 10 kHz when the circuit is trimmed at a 10 V supply with 10 per cent tolerance. The second window is the one to quote for a timing application, because 0.03 per cent per degree over 100 degrees is 3 per cent before the initial tolerance is counted.
Where the 14-lead plastic body is the right choice
A through-hole body earns its place in three situations: a board assembled by hand, a socket that lets a failed timer be swapped in the field, and a frozen drawing where the through-hole footprint already exists and the assembly house is set up for wave solder. The body measures 181.42 square millimetres at 19.3 by 9.4 millimetres against 32 square millimetres for the TSSOP body, so the area penalty is real, and the tube packing of 25 pieces is the wrong format for a pick and place line.
For volume the reels are the practical route, and the family offers three of them: CD4047BM96 in the SOIC D body at 2500 pieces, CD4047BNSR in the SOP NS body at 2000 pieces and CD4047BPWR in the TSSOP PW body at 2000 pieces. The tube rows CD4047BM and CD4047BPW are both obsolete with a blank quantity and a Call TI instruction, so a buyer who needs a handful of surface mount parts for a pilot build is looking at a broken reel rather than a tube. That is the one number on this page that changes a schedule.
What the scan does not publish
The document is a scan of the 2003 Harris original, so the timing curves, the RC nomograph and the trigger level tables are images. This page quotes the two accuracy windows and the drive figures that appear in text and leaves the curves to the printed document. A customer who needs a guaranteed pulse width at a specific temperature and voltage has to take the resistor tolerance, the capacitor tolerance and the 0.015 per cent per degree drift together, and no supplier can do that arithmetic without the actual component specifications. A 1 per cent resistor and a 5 per cent film capacitor already put the pulse 6 per cent wide before the part contributes anything, which is why the trimmed astable window of half a per cent is a bench figure and not a purchase order figure. The three figures that can be quoted from the document are the trigger levels, the 4 milliamp drive and the 600 microamp supply current, and those are the three this page carries.
Second source and long life questions
The CD4047B has no published pin compatible successor, so the practical question for a long life product is not replacement but availability of the bodies that remain. The ceramic rows CD4047BF3A and its .A partner are Active at 25 pieces, which matters for equipment that has to keep a wide temperature drawing alive. The military drawing 8102001CA sits on the same addendum at 25 pieces in a tube with a tin lead finish, which is the row a defence contractor will name.
For a line that has an obsolete tube row on it, the last time buy and LTB planning page sets out how a final order is sized against a build plan, and the date code management page covers how a stock of final buy parts is rotated so the oldest reel is consumed first. Both matter more on a timing part than on a logic gate, because the RC tolerance drifts with nothing while the part sits on a shelf.
What to send with an enquiry
Send the part string, the mode it is used in, the timing value and its tolerance, and the annual quantity. If the board is through-hole, say so, because the tube pack is 25 pieces and a 500 piece build needs twenty tubes booked as one line. If the board is surface mount, the reel size decides the quote: 2500 pieces in SOIC, 2000 in SOP or TSSOP. The BOM scrubbing page explains how we reconcile those three reel sizes against a single build quantity before a schedule is promised.