Contact Us

L7805CV

Brand: ST
L7805CV is a linear voltage regulator from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine L7805CV with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

L7805CV — Voltage Regulator by STMicroelectronics

The L7805CV is an STMicroelectronics voltage regulator in N/A for reliable power management in embedded and industrial applications.

Part Number Decoded — Field by Field

FieldValueMeaning
L7805CVFull Part NumberSTMicroelectronics Voltage Regulator

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberL7805CV
PackageN/A
TypeFixed/Adjustable Voltage Regulator
QualificationIndustrial (-40°C to +125°C)

Product Overview

The L7805CV is an STMicroelectronics voltage regulator in N/A package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.

Key Features & Benefits

Stable Output with Built-in Protection

Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.

Wide Compatibility & Minimal External Components

Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.

Industrial Temperature Range

Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.

Target Applications

Drone & Embedded System Power Rails

Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.

Industrial & Automotive Electronics

Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.

General-Purpose Point-of-Load Regulation

Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.

Frequently Asked Questions

What is the output voltage of the L7805CV?

Check the specific variant. The L7805CV is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.

What capacitors are needed for stability?

Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics L7805CV with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.

L7805CV: the 5 V 1.5 A regulator in the vertical TO-220 body

L7805CV is the 5 V member of the L78 three terminal positive regulator series in the TO-220 body. The series delivers up to 1.5 A with adequate heat sinking, holds 4.8 to 5.2 V at 25 degrees, and carries internal current limiting, thermal shutdown and safe area protection. It needs two capacitors and nothing else, which is why it is still the default answer for a local 5 V rail on a board that has a 8 V to 15 V input.

The order code letters matter. The V is the vertical TO-220 body, the C is the commercial grade of the series, and the plain L7805CV string sits in the same ordering table as the -DG, DPAK, D2PAK and TO-220FP variants. A purchase order that names the family and the voltage without the package letter can land on any of those bodies, and only one of them fits a given board.

Figures come from DS0422 Rev 38, dated February 2025, which covers the whole L78 series and prints a separate electrical table for each voltage.

The numbers that decide whether it fits

FunctionThree terminal fixed positive regulator, internal current limit and thermal shutdown
Output voltage5 V, 4.8 to 5.2 V at 25 degrees
Output currentUp to 1.5 A with adequate heat sinking
Regulation window4.75 to 5.25 V from 5 mA to 1 A over 7 V to 18 V input
Minimum load5 mA for regulation
Quiescent current8 mA at 25 degrees
Dropout voltage2 V at 1 A
Supply rejection62 dB at 120 Hz from 8 V to 18 V input
Output noise40 microvolts per volt of output, 10 Hz to 100 kHz
Short circuit current0.75 A, with a 2.2 A peak
Output resistance17 milliohm at 1 kHz
DriftMinus 1.1 millivolt per degree
PackageTO-220, vertical tab

Heat is the whole argument

A linear regulator burns the difference between input and output as heat. From a 12 V rail at 0.5 A the part dissipates 3.5 W, and at 1 A it dissipates 7 W. The efficiency in that first case is 5 divided by 12, about 42 percent. In a TO-220 body with a tab bolted to a heatsink those numbers are manageable; with no heatsink and a closed enclosure they are not, and the thermal shutdown will cycle the output.

The 2 V dropout at 1 A sets the minimum input. A 5 V output needs at least 7 V in, and a 6.5 V input rail will fall out of regulation before the load reaches 1 A. That is the single most common mistake on a board that inherits the part from an older build with a different input rail.

Where the input to output difference is large and the current is more than a few hundred milliamps, a switching regulator is the better answer and the heat is the reason. Our power management cross reference page lists the switching strings we compare for those cases.

What the two capacitors do

The data sheet test circuit uses 0.33 microfarad at the input and 0.1 microfarad at the output. The input capacitor matters when the regulator sits more than a few centimetres from the bulk capacitor, because the regulator is a gain stage and a long supply trace can make it oscillate. The output capacitor sets the transient response and the stability margin, and a modern low ESR ceramic in place of the 0.1 microfarad part can reduce the phase margin enough to ring.

The minimum load of 5 mA is a real requirement, not a test condition. A board that switches the load off completely can see the output rise above the regulation window, and a 1 kilohm bleeder resistor is the usual fix.

Buying the part

The series is a commodity, and that is where the paperwork matters. Date codes vary widely, the same order code arrives in lead free and older plating, and mixed reels are common in the open market. We check the marking, the date code and the moisture bag at goods in, and the date code management page describes how we keep older stock from reaching a line that has a shelf life rule. The incoming inspection plan page covers the sample plan.

For a build that needs the same regulator in several packages, we quote the family and mark the body on the line rather than substituting silently.

Three questions buyers ask about this string

Is the output 5 V exactly? It is 4.8 to 5.2 V at 25 degrees and 4.75 to 5.25 V over the load and input window, which is the C grade specification. A tighter grade exists in the same table under a different order code.

Can it be used as a 5 V rail from a 24 V supply? It can, but at 1 A the dissipation would be 19 W, which no TO-220 holds without a large heatsink. That is a switching regulator case.

Does it need a heatsink at 300 mA? From a 12 V rail that is 2.1 W, and the tab temperature has to be checked against the ambient. In still air the tab will run hot, and a small clip on heatsink is usually enough.