VN7040ASTR
Product Specifications
VN7040ASTR — Integrated Motor Driver / Smart Power Switch by STMicroelectronics
The VN7040ASTR is an STMicroelectronics integrated motor driver / smart power switch in SOIC-8_150mil for automotive and industrial actuator control applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| VN7040ASTR | Full Part Number | STMicroelectronics Motor Driver / Power Switch |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | VN7040ASTR |
| Package | SOIC-8_150mil |
| Type | Integrated Motor Driver / Smart Power Switch |
| Qualification | Automotive AEC-Q100 / Industrial |
Product Overview
The VN7040ASTR is an STMicroelectronics integrated motor driver / smart power switch in SOIC-8_150mil package. Featuring ST's VIPower technology with monolithic integration of power MOSFETs, gate drivers, and protection/diagnostic circuitry, it simplifies motor control and high-side/low-side switching designs with reduced BOM count and enhanced reliability.
Key Features & Benefits
VIPower Monolithic Integration — Power + Control in One Package
ST's VIPower technology integrates N-channel power MOSFETs, gate drivers, charge pump, and comprehensive protection circuitry on a single die — eliminating external MOSFETs, bootstrap diodes, and sense resistors.
Comprehensive Protection & Diagnostics
Built-in overcurrent, overtemperature (thermal shutdown), undervoltage lockout, and load-dump protection with diagnostic feedback (current sense output, fault status flag) enables self-protecting designs suitable for safety-critical and autonomous systems.
Automotive-Grade Robustness
Designed to withstand harsh automotive and industrial environments including load dump, reverse battery, and extended temperature range for reliable operation in drone payload systems, robotics, and vehicle applications.
Target Applications
Drone Payload & Actuator Control
Drives brushed DC motors, solenoids, and resistive/inductive loads in drone gimbal systems, payload release mechanisms, landing gear actuators, and auxiliary power switching.
Automotive Body & Powertrain
Targets automotive applications including throttle control, EGR valves, HVAC actuators, mirror folding, headlamp leveling, and relay/lamp drivers — all requiring AEC-Q100 qualification.
Industrial Automation & Robotics
Powers motor control, valve actuation, and power distribution in industrial robots, conveyor systems, automated guided vehicles (AGVs), and factory automation equipment.
Frequently Asked Questions
What protection features does the VN7040ASTR include?
The VN7040ASTR features overcurrent protection, overtemperature shutdown, undervoltage lockout, and diagnostic feedback — ensuring robust, self-protecting operation in demanding environments.
Is external current sensing required?
No. The integrated current-sense output provides proportional load current feedback, eliminating the need for external shunt resistors and differential amplifiers.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics VN7040ASTR with full traceability and batch-level QA documentation. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.
VN7040ASTR: a 40 milliohm high side driver with analog feedback
VN7040ASTR is a single channel automotive high side driver in the PowerSSO-16 body, on tape and reel. It switches a grounded load from the supply rail, limits the current into a short, shuts down on overtemperature and reports load current, supply voltage and chip temperature through one multiplexed analog pin. The 40 milliohm on resistance and the 34 A typical current limit put it in the lamp and actuator class rather than the motor bridge class.
The data sheet DS10829 Rev 5, dated April 2019, covers both the AJ and the AS body. The AS suffix is the PowerSSO-16, the AJ suffix is the SO-8, and both share one electrical table, so a customer who changes body without changing the order code letter ends up with a footprint that does not fit. That is the first thing we check on an incoming BOM line for this family.
The electrical window
| Function | Single channel high side driver with MultiSense analog feedback |
| Maximum transient supply | 40 V |
| Operating range | 4 V to 28 V |
| On resistance | 40 milliohm typical per channel |
| Current limitation | 34 A typical |
| Standby current | 0.5 microamp maximum |
| Logic levels | 3 V and 5 V CMOS compatible |
| Diagnostics | Load current, supply voltage and chip temperature, multiplexed on one pin |
| Fault detection | Overload, short to ground, short to supply, off state open load, thermal shutdown |
| Latch behaviour | Configurable latch off with a dedicated FaultRST pin |
| Supply faults covered | Loss of ground, loss of supply, reverse battery with external components |
| ESD | 4 kV human body model on input and output, 750 V charged device model |
| Junction range | Minus 40 to plus 125 degrees in the grade 1 window printed by the family |
| Package | PowerSSO-16 for the AS suffix, SO-8 for the AJ suffix |
| Qualification | AEC-Q100 |
Conduction loss and the two copper figures in the thermal table
At 40 milliohm, 5 A costs 1 W in the switch and 10 A costs 4 W. On the PowerSSO-16 body the thermal table prints a junction to ambient figure of 55 degrees per watt on a four layer board and 21.2 degrees per watt on a two layer board with 2 square centimetres of heatsink copper, so the same 4 W is either a 220 degree rise or an 85 degree rise depending on the copper under the package. Neither figure is comfortable at 10 A continuous in a hot enclosure, and both explain why the 34 A current limit is a fault rating rather than a running current.
The lesson for a quotation is that the current rating of a high side driver is decided by the board, and the board is decided by the customer. We ask for the copper area and the ambient before we commit a part to a load, and the power management cross reference page lists the drivers with lower resistance when the arithmetic does not close.
What the diagnostic pin can and cannot tell you
The multiplexed analog output reports load current with a proportional mirror, the supply voltage and the chip temperature. It does not report which of those three is on the pin at a given moment, because the selection comes from the logic inputs. A controller that samples the pin while it is set to the temperature channel and treats the value as a current will read a plausible number that means nothing.
Off state open load detection needs an external pull up on the output, and the value of that resistor sets the threshold. The data sheet has a dedicated section on that dimensioning, and it is the section to read before the harness is defined, because a pull up that also feeds an LED load will light it faintly in the off state.
Reverse battery protection is stated with external components, so the ground network of the module has to be part of the review. A board that assumes the driver survives a reversed jump start on its own is relying on something the document does not promise.
Where this driver is used
The application list names turn indicators up to P27W or SAE1156, rear lamp combinations, and protected supplies for radar and sensor modules in advanced driver assistance systems. In practice it turns up in body control modules, trailer lighting, heated seats and sensor supply gating, where a single channel with a real current reading is worth more than a plain switch.
We supply the string for automotive lines and check the reel, the date code and the moisture bag at goods in. The incoming inspection plan page sets out the sample plan we use, and the one stop BOM sourcing route covers the rest of the module BOM on the same shipment.
Three questions buyers ask about this string
Does the AS body need a different footprint from the AJ? Yes. PowerSSO-16 and SO-8 are different land patterns, and the electrical table is shared, so the body letter is the difference that matters to the assembly line.
Can the current limit be used as a fuse? No. It is a typical figure for a fault event, and the part is specified to survive the event and recover, not to interrupt a persistent overload indefinitely.
Is the standby current low enough for a parked vehicle? At 0.5 microamp maximum it is, provided the logic inputs are driven to a defined level rather than left floating.