Contact Us

VNH7100BASTR

Brand: ST
VNH7100BASTR is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine VNH7100BASTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

VNH7100BASTR — Automotive Fully Integrated H-Bridge Motor Driver by STMicroelectronics

The VNH7100BASTR is STMicroelectronics' automotive fully integrated h-bridge motor driver. Supplied by SUPERB Automation with verified sourcing and competitive lead times.

Part Number Decoded — Field by Field

FieldValueMeaning
VNH7100BASTRFull Part NumberAutomotive Fully Integrated H-Bridge Motor Driver

Quick Specifications

ParameterValue
TypeH-Bridge Driver
RDS(on)200mΩ per leg (HS+LS)
Supply Voltage4V–28V
Output Current12A continuous
ProtectionOvercurrent, Overtemp, Undervoltage
PackageSO-16N
InterfaceParallel (PWM + DIR)
DiagnosticsCurrent sense + fault flag

Product Overview

Automotive Fully Integrated H-Bridge Motor Driver from STMicroelectronics. Supplied by SUPERB Automation with full traceability and batch-level QA documentation.

Key Features & Benefits

Fully Integrated H-Bridge — No External MOSFETs Required

The VNH7100BASTR integrates two monolithic half-bridges with all gate drivers, charge pump, and protection circuitry in a single SO-16N package. This eliminates the need for external MOSFETs, gate drivers, bootstrap diodes, and current-sense resistors — dramatically reducing BOM count and PCB area.

Automotive-Grade Robustness — AEC-Q100 Qualified

Certified to AEC-Q100 automotive standards, the VNH7100BASTR withstands harsh operating conditions including load dump, reverse battery, and extended temperature range (−40°C to +150°C). Ideal for drone payload actuators, gimbal motors, and ground support equipment where reliability is non-negotiable.

Comprehensive Protection Suite

Built-in overcurrent, overtemperature, and undervoltage protection with diagnostic feedback (current sense and fault flag) enable robust, self-protecting designs without additional sensing circuitry — critical for autonomous drone systems that must handle actuator stall conditions gracefully.

Target Applications

Drone Gimbal & Payload Actuators

Drives brushed DC motors in 2-axis/3-axis camera gimbals, payload release mechanisms, and landing gear actuators on professional inspection and delivery drones. The integrated current-sense output enables precise torque/position control without external shunt resistors.

Automotive Actuator Control

Designed for automotive throttle control, exhaust gas recirculation (EGR) valves, HVAC flap actuators, and mirror positioning — all requiring bidirectional motor control with comprehensive diagnostics.

Robotics & Industrial Motor Control

Powers small-to-medium brushed DC motors in robotic grippers, conveyor actuators, valve controllers, and automated test equipment where integrated protection and diagnostics reduce system complexity.

Frequently Asked Questions

Does the VNH7100BASTR require an external charge pump?

No. The VNH7100BASTR integrates a full charge pump for high-side gate drive, requiring only a single supply voltage (4V–28V) and logic-level PWM/DIR control signals — compatible with 3.3V and 5V MCU GPIOs directly.

Can this driver be used for brushless DC (BLDC) motors?

No, this is a brushed DC motor H-bridge. For BLDC motors, ST offers the STSPIN family (e.g., STSPIN32F0, STSPIN830) which integrate 3-phase gate drivers. The VNH7100BASTR is ideal for brushed motors in gimbals, actuators, and auxiliary drives.

What is the minimum order quantity?

Contact SUPERB Automation for a tailored quote. Available in tape & reel (1,000 pcs/reel) or cut tape for prototypes.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics VNH7100BASTR components with full traceability and batch-level QA documentation. Whether you need prototype quantities or production volumes, we source through verified channels with competitive lead times. Contact us with your target quantity and delivery date — we'll respond with a detailed quotation within 24 hours.

VNH7100BASTR: a full bridge in SO-16N with analog current feedback

VNH7100BASTR is an automotive full bridge motor driver in the SO-16N body, supplied on tape and reel. Inside the package sit two high side drivers and two low side switches built on the VIPower M0 process, with the protection and diagnostic circuitry on the same die as the switches. The bridge drives a brushed motor in both directions, brakes it, and reports the motor current back to the controller through one analog pin.

The part is AEC-Q100 qualified. The order code breaks down as the base part number plus the STR tape and reel suffix, and the data sheet device summary prints a single order code for the SO-16N package, so the tube version does not exist for this string. That matters at the purchase order stage, because a line asking for a tube part number has no matching row in the vendor table.

The figures in this page come from DocID029596 Rev 2, dated March 2017, read in full this round. The data sheet prints 15 A of output current in the feature list and 12 A in the device type table next to the 100 milliohm per leg resistance, and both numbers are quoted here rather than smoothed into one.

What the pins give the controller

FunctionAutomotive full bridge motor driver, two high side and two low side switches
On resistance100 milliohm typical per leg
Output current15 A in the feature list, 12 A in the device type table
Maximum supply38 V
PWMUp to 20 kHz on the PWM pin
Logic inputs3 V CMOS compatible, INA, INB, PWM and SEL0
Current feedbackMultiSense analog output proportional to motor current
Fault reportingShort to ground, short to supply, off state open load, thermal shutdown flag
ProtectionsUndervoltage shutdown, overvoltage clamp, cross conduction lockout, current and power limitation
Supply faults coveredLoss of ground and loss of supply
Operating modesFull bridge and half bridge, with a standby mode
PackageSO-16N, ECOPACK
QualificationAEC-Q100

Conduction loss decides the copper under the body

At 100 milliohm per leg, one leg carrying 5 A burns 2.5 W, and both legs carry current whenever the bridge is driving, so the package sees about 5 W at that current. At 10 A the same arithmetic gives 10 W per leg, and at the 12 A of the type table it gives 14.4 W. Those figures are why a 15 A rating and a 38 V supply do not add up to a 15 A continuous load in a sealed box. The current has to be traded against the copper area on the board and against the ambient inside the enclosure.

The SO-16N body removes heat through the lead frame and the pins, not through a exposed pad, so the copper that matters is the supply and output traces plus the ground pour under the body. A driver run at 10 A with 10 W per leg needs a thermal calculation before the board is committed, not a rule of thumb. Our power management cross reference page lists the bridge families we compare when a customer needs more current in the same footprint.

The 20 kHz PWM ceiling sets the other limit. Above that frequency the switching loss in the bridge rises with every edge and the internal charge pump has less time to refresh the high side gate, so a motor that needs 25 kHz for acoustic reasons is not a candidate for this part.

Reading the MultiSense pin

MultiSense delivers a current proportional to the motor current, and the SEL0 pin selects which of the internal measurements reaches that pin. The controller turns the current into a voltage across a resistor to ground, then digitises it. Two things trip a first article: the resistor value chosen against the sense ratio in the electrical table, and the settling time after a direction change, because the sense path is multiplexed and needs a defined blanking window in the sampling routine.

Because the same pin also carries the fault flags, the firmware has to distinguish a fault state from a current reading by the SEL0 setting and the timing, not by the voltage alone. A bridge that reports a plausible current while a leg is shorted is the classic symptom of a sampling routine that ignores the mode bit. The pin to pin cross reference page describes how we compare diagnostic behaviour, not only pinout, before a substitution is approved.

Where the part fits, and where it does not

Typical loads are seat adjustment, mirror fold, door lock, throttle body and small pump motors on 12 V. The 38 V supply ceiling covers a load dump clamp, and the loss of ground and loss of supply protections cover the harness faults that kill unprotected bridges in the field. For a 24 V system the part is outside its window, and the 58 V high side family is the correct starting point.

We hold this string for automotive builds where the customer supplies the motor and the harness drawing, and we check the sense resistor and the freewheel path against the motor inductance before the parts are booked to a line. The component traceability report we issue for such builds records the date code and the reel behind every lot.

Three questions buyers ask about this string

Is the 12 A or the 15 A figure the right one for a quotation? Both are in the document. The type table gives 12 A with the 100 milliohm resistance, and the feature list gives 15 A. We quote the thermal calculation, not the headline number.

Can it run two motors? No. It is one full bridge, which is one motor, or two independent half bridges. A dual motor load needs two packages.

Does the STR suffix mean a different die? No. It is the tape and reel packing for the same SO-16N body, and it is the only order code the device summary prints.