Contact Us

BQ25887RGER

Brand: Texas Instruments
Texas Instruments BQ25887RGER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ25887RGER — Power Management & Signal Chain | Superb Automation

BQ25887RGER

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ25887RGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ25887RGER two cell boost charger with cell balancing for USB input

The BQ25887RGER is the balancing member of the two cell boost charger family. It charges a 2s pack from a USB adapter at up to 2 A, runs at 1.5 MHz, and adds an internal balancing path that can move up to 400 mA between the cells while the pack is charging. For a pack where the two cells drift apart over a few hundred cycles, that removes the external balancer that would otherwise sit next to the charger.

The electrical core is the same as the non balancing sibling: 3.9 V to 6.2 V input, 20 V absolute maximum, input current limit from 500 mA to 3.3 A in 100 mA steps, charge voltage accuracy of plus or minus 0.5 percent, and a 16 bit ADC that reports each cell separately. The difference is the mid point pin, the balance pin and the internal FETs that connect them, which is what makes a two cell pack with mismatched cells practical on a small board.

Key parameters taken from the BQ25887RGER document

Function2-cell boost mode charger with cell balancing and I2C control
PackageVQFN-24, 4.00 mm by 4.00 mm
Input range3.9 V to 6.2 V operating, 20 V absolute maximum
Switching frequency1.5 MHz typical, 1.35 MHz to 1.65 MHz window
Fast charge currentup to 2 A
Charge voltage accuracyplus or minus 0.5 percent
Charge current accuracyplus or minus 5 percent, plus or minus 7.5 percent on input current
Balancing currentup to 400 mA, set by the resistor on the balance pin
Balance FET resistance1 ohm typical, 1.2 ohm maximum, upper and lower paths
Balance enable threshold3.65 V to 3.75 V rising on the low cell, 200 mV hysteresis
Monitoring16 bit ADC for bus voltage and current, each cell voltage, charge current, NTC and die temperature
Efficiency93.4 percent at 5 V adapter, 7.6 V battery, 1 A charge

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The balancing current is set by a resistor, and the value has a ceiling. The vendor states 400 mA as the maximum recommended balancing current at a 4.2 V cell with a 9.5 ohm resistor, and warns that the resistor chosen should not push past that limit. A pack with tall cells or a large capacity needs a longer balance window rather than a larger current, because the internal FETs are 1 ohm and dissipate the difference as heat.

Balancing only starts above 3.7 V on the lower cell with 200 mV of hysteresis. That is deliberate: the part does not try to balance a deeply discharged pack, where the two cells are far apart and moving current between them would only add heat. In practice this means the balance window is the top of the charge cycle, so a product that rarely reaches full charge will not balance at all.

The mid point connection is not optional on this part. The pin at the junction of the two cells both senses the lower cell and returns balance current, and the vendor requires a current limit resistor on the balance pin. A board that leaves the mid point unconnected will charge, but the balancing function and the lower cell measurement are both lost, and the fault looks like a software problem because the registers still respond.

Because the two cell measurements come through the same ADC that reads the bus, the cell mismatch is visible in the telemetry. That is useful for field data: a pack whose cells diverge faster than expected usually shows it in the reported per cell voltages long before the capacity drops.

  • Two cell packs with cells from different lots, or packs rebuilt with one new cell, benefit most from the internal balancing.
  • The balance path is inside the charger, so no separate balancer IC, no extra inductor and no extra firmware loop are needed.
  • Charge voltage and current accuracy are the same as the non balancing sibling, so a pack can move between the two parts without changing the charge profile.
  • The per cell ADC reading gives the pack maker a factory record of cell matching before the pack is sealed.

Which projects this part fits

This part fits two cell products that are expected to last several hundred cycles and cannot afford cell drift: robotic toys and drones with 2s packs, virtual reality headsets, IP cameras with battery backup, and portable instruments. Products that never fully charge, such as continuously powered devices with a small pack, gain nothing from balancing and should use the plain charger instead. The drone and UAV component page covers the packs and connectors we supply with this charger family, and power management cross reference lists the alternatives.

Setting the balance current and proving it on the first article

The balancing current is set by the resistor on the balance pin, and the vendor states the ceiling clearly: 400 mA maximum recommended at a 4.2 V cell with a 9.5 ohm resistor. That figure is the current through the internal FET when the two cells are far apart, and it falls as the cells come together, so the number is a peak rather than a steady value.

ItemValue
Maximum recommended balance current400 mA at 4.2 V with a 9.5 ohm resistor
Internal balance FET resistance1 ohm typical, 1.2 ohm maximum, upper and lower paths
Balance qualification3.65 V to 3.75 V rising on the lower cell, 200 mV hysteresis
Mid point connectionRequired: senses the lower cell and returns the balance current
Charge current ceiling2 A, with balancing running at the same time

On the first article, the useful test is two cells held about 100 mV apart at the top of the charge range with balancing enabled. The current through the balance resistor should match the calculated value within the resistor tolerance, and the body temperature should stay under the thermal limit for the length of a real charge. A pack that balances correctly but runs hot in the enclosure will fold back its charge current and take longer to fill than the customer was promised.

The mid point is also the sense point for the lower cell. A board that connects it through a long track or a thin via reports a lower cell voltage that is offset by the track resistance times the balance current, which looks like a permanently unbalanced pack in the telemetry. Keeping that connection short and separate from the balance current return is the difference between a reading and a measurement.

Questions that come up before a purchase order is released

Can the balancing current be increased above 400 mA?

Not within the vendor recommendation. The internal FETs are about 1 ohm, so a higher current means more heat inside a 4 mm by 4 mm body. Packs that need faster balancing use an external balancer with its own FETs, and this charger then runs without the balance function.

Does balancing work when the pack is discharging?

The qualification threshold is a cell voltage above about 3.7 V with hysteresis, and balancing is intended for the charge phase. A pack that spends its life between 3.6 V and 3.9 V will see little or no balancing, which is one reason field data on cell drift matters more than the register setting.

What happens if one cell is much weaker than the other?

The charger reports both cell voltages and the difference is visible. Balancing can only move a limited current, so a cell that is far below its partner will not be recovered by the charger; the pack should be reworked or rejected at test rather than shipped with a large initial mismatch.

How SUPERB handles this line

We supply the BQ25887RGER with the balancing resistor value calculated for the pack, and we can kit the mid point components with the charger so the two cell stack arrives complete. If a product currently uses the non balancing charger and field returns show cell drift, send us the return data and the pack specification; we will compare the two parts and say whether the swap is enough or whether the pack needs an external balancer. Start with the drop in replacement check page.