CD4053BE
Product Specifications
CD4053BE
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4053BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4053BE: three independent 2 to 1 analogue switches in the 16-lead plastic DIP
The CD4053BE is the plastic dual in line member of the CD4053B, three single pole double throw analogue switches with separate control pins on one die. The vendor describes the family in one line as a 20 V, 2 to 1, three channel analogue multiplexer with logic level conversion and marks it ACTIVE. The parametric table gives three channels, a 2 to 1 single pole double throw configuration, single supply options of 5, 12, 16 and 20 V, dual supply options of plus or minus 2.5, 5 and 10 V, a typical on resistance of 125 ohms, an on capacitance of 9 picofarads, a maximum on state leakage of 0.3 microamps, a typical supply current of 0.04 microamps, a bandwidth of 30 MHz and a 10 milliamp continuous channel current.
The row reads Active, plastic DIP with 16 leads at 181.42 square millimetres, 25 pieces in a tube, RoHS yes with a nickel palladium gold lead finish, no moisture sensitivity level because a through-hole body is not reflow classified, minus 55 to plus 125 degrees and the marking CD4053BE. The ceramic body sits beside it as CD4053BF and CD4053BF3A, and the military drawing row 8101801EA is on the same addendum at 25 pieces in a tube.
The CD4053BE row as the vendor addendum publishes it
| Part class | Triple 2 to 1 analogue switch, single pole double throw |
| Vendor descriptor | 20 V, 2 to 1, three channel analogue multiplexer, logic level conversion |
| Vendor document | SCHS047O, revised May 2026, CD4051B, CD4052B and CD4053B |
| Configuration | 2 to 1, three channels, three independent control pins |
| Single supply | 5, 12, 16 and 20 V, no 3.3 V row in the parametric table |
| Dual supply | Plus or minus 2.5, 5 and 10 V |
| Digital input range | 3 V to 20 V, independent of the analogue rails |
| Analogue range | Up to 20 V peak to peak |
| On resistance | 125 ohms typical at 15 V |
| On state leakage | Plus or minus 10 pA typical at 15 V, 0.3 microamps maximum |
| Quiescent power | 0.2 microwatts typical |
| Bandwidth | 30 MHz, the widest of the three parts in the document |
| On capacitance | 9 picofarads typical |
| Continuous current | 10 milliamps maximum through any channel |
| Switching | Break before make |
| ESD | 3000 V HBM, 2000 V CDM |
| Package for this code | PDIP (N), 16 leads, 181.42 square millimetres |
| Packing | 25 pieces in a tube |
| Status | Active, production |
| Part marking | CD4053BE |
| SOIC reel row | CD4053BM96, 2500 pieces, marking CD4053M |
| TSSOP reel row | CD4053BPWR, 2000 pieces, marking CM053B |
| Obsolete rows of the family | CD4053BM, CD4053BMT, CD4053BPW, CD4053BM96G3, CD4053BPWRG3 |
Three switches that do not have to move together
The 4051B and the 4052B share their address lines across the channels, which is the right architecture for a scan and the wrong one for three unrelated selections. The 4053B gives each of its three switches its own control pin, so a board can route audio to one path while it shorts a gain resistor in another and grounds an input in the third, all with three independent logic lines. That is why the part appears in signal routing rather than only in data acquisition.
The common pins make the same switch usable in either direction, so one of the three can be a 2 to 1 multiplexer while another is a changeover relay replacement and the third is a mute switch that shorts a node to ground. The 9 picofarad on capacitance is the lowest in the family, which is what makes it usable on the widest bandwidth of the three parts at 30 MHz.
The 3.3 V question on this member
The parametric table for the CD4053B lists single supply options of 5, 12, 16 and 20 V. It does not list 3.3 V, while the CD4051B and the CD4052B in the same document do. A board running a 3.3 V analogue rail therefore cannot read a published 3.3 V single supply row for this part, and a purchasing or engineering check that copies the 4051B line across to the 4053B will miss that difference.
In practice the part works at 3.3 V for many signal levels, and the vendor's feature list gives a 3 V to 20 V single supply range with a note that performance degrades below 3 V. What the parametric table is telling a reader is that the published characterisation points start at 5 V. A board that needs guaranteed on resistance at 3.3 V has to measure it, and a board that needs a guaranteed row has to move the single 2 to 1 function onto a part that publishes 3.3 V.
Through-hole routing and the socket argument
Three independent switches in one 16-lead body save two packages against a discrete changeover solution, and the through-hole body makes the part serviceable in equipment that is repaired rather than replaced. A mixing console, a test bench router or a medical instrument with a socketed card all take this body for the same reason: the part can be lifted with a soldering iron and a bulb, and no reflow profile is needed to put it back.
The area cost is 181.42 square millimetres at 19.3 by 9.4 millimetres, which is five times the TSSOP body. On a card with three or four of these parts the difference is a board size, and on a card with one it is a placement convenience.
Signal behaviour and the limits that are not in the headline
One hundred and twenty five ohms of on resistance and 9 picofarads of on capacitance set the useful bandwidth. Into a 10 kilohm load the switch behaves as a small series resistance and the 30 MHz figure is close to the small signal bandwidth; into a 1 megohm load the capacitance dominates and the corner falls by an order of magnitude. A board that routes a low level audio signal into a high impedance buffer therefore has to treat the multiplexer as a capacitance and not as a resistor.
The 10 milliamp continuous current limit is per channel, and the common pin of a changeover switch carries the load whichever way it is thrown. A switch that drives a 20 milliamp load is outside the rating even though only one channel is conducting at a time. That is the figure that separates a signal router from a power router, and the family is deliberately on the signal side of the line.
Replacement and availability
TI lists the TMUX4053 as a drop-in replacement with upgraded functionality against this family, with 1.8 V compatible logic and a smaller body, but its analogue range is narrower than the plus or minus 10 V of the original. A board that runs a plus or minus 10 V signal stays on the CD4053B; a board that is being revised to a lower rail gains the modern part and the smaller package.
Inside the family the tube rows are thinning: the SOIC tube, the TSSOP tube and two older reel suffixes are obsolete, and the live surface mount rows are the 2500 piece SOIC reel and the 2000 piece TSSOP reel. A customer with a through-hole drawing is unaffected, because the plastic DIP still ships in a 25 piece tube. The obsolete part cross reference hub collects the three parts of this family in one place, and the one stop BOM sourcing page explains how a bill with all three is consolidated into one order.
What to send with an enquiry
Send the string, the analogue rails, how many of the three switches are used and the annual quantity. If the board runs 3.3 V, say so, because that is the one number on this page that changes the recommendation. If the board is socketed, the .A row of the same string is also available and widens the stock that can be quoted against.