Contact Us

CD4013BM96

Brand: Texas Instruments
Texas Instruments CD4013BM96 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4013BM96 — Power Management & Signal Chain | Superb Automation

CD4013BM96

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4013BM96 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4013BM96: two D flip-flops on a 2500 piece reel

CD4013BM96 is the tape and reel member of the CD4013B family, two independent D-type flip-flops with set and reset, in a 14-lead SOIC, 2500 pieces on a large reel. The vendor descriptor is CMOS Dual D-Type Flip Flop, the document is the CD4013B data sheet revision E, and the parametric table gives two channels, 24 MHz maximum clock, 6.8 mA sink and source, 600 microamps maximum supply current, and standard speed with propagation above 50 ns. The die is the same one the plastic DIP carries, so this page concentrates on the packing, the handling and the two numbers that change with the rail, rather than repeating the function description.

The addendum lists CD4013BM96 as Active in production, SOIC (D) with 14 leads, 2500 pieces on a large tape and reel, RoHS yes with a nickel-palladium-gold finish, moisture sensitivity level 1 at a 260 degree peak with unlimited floor life, minus 55 to plus 125 degrees, and the marking CD4013BM. The tube member of the same body is CD4013BM at 50 pieces, and the same document carries the SOP and TSSOP rows at 2000 pieces each, so the reel is one of three surface mount formats for one die.

The CD4013BM96 row as the vendor addendum publishes it

Part classDual D-type flip-flop with independent set and reset
Vendor descriptorCMOS Dual D-Type Flip Flop
Vendor documentCD4013B data sheet revision E
Supply range3 V to 18 V
ChannelsTwo, each with data, clock, set, reset and complementary outputs
Clock frequency, parametric table24 MHz maximum
Toggle rate, vendor feature line16 MHz typical at 10 V
Output drive, parametric table6.8 mA sink and source
Supply current, maximum600 microamps
Package for this codeSOIC (D), 14 leads
Body area, vendor figure51.9 square millimetres, 8.65 mm by 6 mm
Packing2500 pieces on a large tape and reel
Lead finishNIPDAU
Moisture levelLevel 1, 260 degrees peak, unlimited floor life
Operating rangeMinus 55 to plus 125 degrees
StatusActive, production
Part markingCD4013BM
Reel rows in the addendumCD4013BM96, CD4013BM96.A and CD4013BM96E4, all 2500 pieces
Tube member of the same bodyCD4013BM, 50 pieces
SOP and TSSOP rowsCD4013BNSR and CD4013BPWR, 2000 pieces each
Ceramic rowsCD4013BF and CD4013BF3A, wide screening

Two flip-flops per reel pocket, and the arithmetic that follows

A reel of 2500 packages carries 5000 flip-flops, which is the number that matters when the function is a divider chain. A divide by four needs one package per channel pair, so a reel covers 2500 boards that carry one 4013 each, or 1250 boards that carry two. On a board with a four stage divider the same reel covers 625 boards, and that arithmetic usually decides between one reel and two before the purchase order is written.

Because the part is level 1 at a 260 degree peak, the reel does not need a bake and does not carry a floor life clock, which matters on a line that runs the same reel across several weeks. The one handling rule that does apply is the leader: the first 200 mm of tape on a used reel should be checked for splices before the feeder is loaded, because a spliced leader is where a mislabelled or mixed lot usually hides.

The 24 MHz limit against a 16 MHz typical toggle

The parametric table lists 24 MHz as the maximum clock frequency and the vendor feature line says 16 MHz typical toggle at 10 V. Reading the two together, the typical behaviour at the highest rail is below the absolute limit, which is normal, and the limit is the number a timing budget must respect. At 5 V the part is slower and the vendor does not print a 5 V clock figure in text, so a 5 V circuit should be checked against the 5 V table in the document rather than against either number.

What the limit means in practice is that this part is comfortable as a debounce latch, a divide by two stage, or a slow event counter, and uncomfortable as a fast prescaler. A circuit that needs a 50 MHz divider takes a 74HC or 74AC part, which brings a 6 V supply ceiling and loses the 18 V range. The 4013 is chosen for the range and the static behaviour, not for speed.

Set and reset: the pins that decide whether the board is reliable

Every input on a CMOS flip-flop needs a defined level, and the 4013 has five per flip-flop, which is more than any gate in the family. Set and reset are active high and act independently of the clock, so an unconnected set pin can hold the output high with no clock at all, which is a failure that looks like a dead channel. A 100 k resistor to ground on each of the four asynchronous pins holds them low across the temperature range, because the input leakage is 1 microamp at 18 V and 125 degrees and the resistor drops 0.1 V at that current.

The data input needs the same treatment. A floating data line picks up the clock edge through stray capacitance and the flip-flop captures a level that depends on the board arrangement rather than on the circuit, which is the classic intermittent fault that appears only on some boards. Tying the input through a resistor to the driving source, and never leaving it open on an unused channel, is the whole rule.

Where this code sits in the family and in the catalogue

The family runs PDIP, SOIC tube, SOIC reel, SOP reel, TSSOP reel and ceramic CDIP, and the reel SOIC is the format a reflow line wants. The TSSOP row is the answer when 8.65 mm of body width does not fit, and the SOP row is the 1.27 mm pitch alternative that some inspection departments prefer. The ceramic rows are a different procurement conversation, because they carry screening and a tin lead finish option that a commercial board does not need.

The nearest functional alternative in the catalogue is the CD4027B dual JK flip-flop, which toggles with both inputs high instead of needing the Q bar feedback. The CD4013B wins on data capture and the CD4027B wins on toggle logic, and a board that needs both usually carries one of each rather than building one from the other.

Incoming checks on the reel and the part

The label should read CD4013BM96 at 2500 pieces with a date code inside the customer window, and the body marking will read CD4013BM, which is expected. A first article test from the first pocket should clock both flip-flops and exercise set and reset on each, because a part that toggles correctly can still have a weak asynchronous input. The 600 microamp supply current limit is a useful incoming screen as well, since it is a maximum rather than a typical and a part well above it is either damaged or not what the label says.

The reference pages are the incoming inspection plan, date code management, and the one stop BOM sourcing route when the reel is part of a kit that also carries the passives and the connector.

Questions that come up on this code

Whether a reel ordered as BM96 can be split across two machines. It can, with the reel respooled and both halves labelled, but the traceability then has to follow the split rather than the original label.

Whether the 600 microamp supply current covers both flip-flops. It covers the package, which is why it is the right number to use for a thermal or a battery life estimate.

Whether the outputs can drive a MOSFET gate. At 6.8 mA the gate charges slowly and the switching loss lands in the transistor, so a gate driver belongs between the flip-flop and the FET.

Whether a 4013 can replace a 4027 in an existing board. Not without rewiring, because the pinout and the input structure differ, and the 4027 body is 16 leads rather than 14.