Contact Us

AM26LV32EIDR

Brand: Texas Instruments
Texas Instruments AM26LV32EIDR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AM26LV32EIDR — Power Management & Signal Chain | Superb Automation

AM26LV32EIDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The AM26LV32EIDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

AM26LV32EIDR: 3.3 V quad RS-422 receiver with 15 kV bus protection and open fail-safe

AM26LV32EIDR is the receive end of a 3.3 V balanced link that leaves the enclosure in a SOIC body of 16 pins. The part receives four balanced pairs from a 3.3 V supply at rates to 32 MHz, with a 7 V common mode range, 200 mV of sensitivity and 35 mV of hysteresis. The bus pins carry 15 kV human body model protection, the enable inputs accept 5 V logic, and the outputs go high when the inputs are open. Dissipation is 27 mW typical.

Order code and package

Order codeAM26LV32EIDR
Functionquad differential line receiver, three-state outputs
StandardTIA/EIA-422-B and ITU recommendation V.11
Supplysingle 3.3 V rail
Bus protection15 kV human body model and IEC 61000-4-2 on the four pairs
Enable5 V compatible inputs while the supply is 3.3 V
Fail-safeopen circuit false state prevented, output high
PackageSOIC, 16 pins, 9.90 mm by 3.91 mm
Temperature rangeminus 40 to plus 85 C
Power downIoff disables the outputs when the rail is off
DatasheetSLLS849 revision D
Compatibilitypin to pin with AM26C32 and AM26LS32

Electrical parameters that decide the application

Common mode range7 V with 200 mV of differential sensitivity
Hysteresis35 mV typical, against 60 mV on the 5 V receiver in the same family
Dissipation27 mW typical, which is the whole package at 3.3 V
Switching rate32 MHz
Outputthree-state, so the receiver can sit on a shared bus
Fail-safean open pair produces a high output rather than an undefined level
Input levelsthe enable pins accept 5 V, so an older controller can drive them directly
Power downIoff stops current flowing back through the part into a dead rail
PackageSOIC 16 and VQFN 16
Hysteresis note35 mV is below the 60 mV of the 5 V member, so the substitution changes noise immunity of the receive path

Points to check before this part goes on a BOM

Thirty-five millivolts of hysteresis is a tighter window than the 60 mV of the 5 V receiver it replaces. On a quiet bench both work; on a pair running beside a switching supply the smaller window is where noise induced on the cable starts to appear as extra edges at the output.

The fail-safe rule covers an open pair. A terminated pair with no active driver presents near zero volts and is not the same condition, so a bus that can lose its driver needs bias resistors or a receiver with a specified zero-volt fail-safe window.

Seven volts of common mode range with 200 mV of sensitivity is the standard window, and it is the sensitivity rather than the window that usually fails first: at the end of a long cable the differential amplitude can fall below 200 mV while the common mode stays well inside the window.

Twenty-seven milliwatts typical for four receivers is a quarter of what the 5 V family takes, and it is the reason a 3.3 V link can run from a small regulator. The number covers the whole package, not per channel.

Pin compatibility with the AM26C32 covers the functions, not the thresholds. The input levels and the hysteresis differ, so a board that swapped the part without a re-test has a receive path whose noise margin was never measured.

Where this order code fits

Boards pairing this receiver with the protected driver of the same family get the IEC level protection at both ends of the cable. Boards comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and boards replacing a part that has gone end of life start from the Defense Grade Components page.

Questions buyers ask

Is the output defined when the cable is unplugged? Yes. An open pair produces a high output, which is the documented fail-safe state.

Can it replace an AM26C32 directly? Pin functions match, but the hysteresis is 35 mV instead of 60 mV and the supply is 3.3 V, so the noise margin has to be re-measured.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.