L6599ADTR
Product Specifications
L6599ADTR — Voltage Regulator by STMicroelectronics
The L6599ADTR is an STMicroelectronics voltage regulator in SOIC-16_150mil for reliable power management in embedded and industrial applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| L6599ADTR | Full Part Number | STMicroelectronics Voltage Regulator |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | L6599ADTR |
| Package | SOIC-16_150mil |
| Type | Fixed/Adjustable Voltage Regulator |
| Qualification | Industrial (-40°C to +125°C) |
Product Overview
The L6599ADTR is an STMicroelectronics voltage regulator in SOIC-16_150mil package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.
Key Features & Benefits
Stable Output with Built-in Protection
Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.
Wide Compatibility & Minimal External Components
Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.
Industrial Temperature Range
Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.
Target Applications
Drone & Embedded System Power Rails
Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.
Industrial & Automotive Electronics
Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.
General-Purpose Point-of-Load Regulation
Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.
Frequently Asked Questions
What is the output voltage of the L6599ADTR?
Check the specific variant. The L6599ADTR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.
What capacitors are needed for stability?
Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics L6599ADTR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.
L6599ADTR: a resonant half bridge controller up to 500 kHz in SO16 narrow
L6599ADTR is the improved revision of the L6599 high voltage resonant controller from STMicroelectronics, in the SO16 narrow body, tape and reel. It drives a half bridge at a fixed 50 percent duty cycle and varies the frequency instead, up to 500 kHz, which is the control method an LLC or an LC series resonant converter uses to keep the primary switches turning on at zero voltage. The A revision is the one in full production; the original L6599 carries the status not recommended for new designs, and the difference matters when a build is being re-planned.
What the part brings to a resonant stage is the timing, the protection and the high side drive in one body. The oscillator is trimmed, the soft start is non linear so the output voltage rises monotonically, the two level overcurrent protection first shifts the frequency and then latches, and the high side driver works from a 600 V rail with an integrated bootstrap diode. That last item removes a discrete diode and its charging path from the bill.
Vendor facts for the A revision
| Function | Resonant half bridge controller, variable frequency |
| Duty cycle | 50 percent fixed |
| Operating frequency | Up to 500 kHz |
| Oscillator | High accuracy |
| Overcurrent protection | Two level, frequency shift first, latched shutdown second |
| High side driver | 600 V rail compatible, integrated bootstrap diode, high dV/dt immunity |
| Gate drive current | Minus 300 and plus 800 milliamps, high side and low side, with undervoltage pull down |
| Light load | Burst mode operation |
| Other inputs | Latched disable, power on and off sequencing, brownout protection |
| Interface | Direct interface with a PFC controller |
| Package | SO16 narrow, also DIP16 in the family |
| Named applications | LCD and plasma television, desktop and entry server, telecom SMPS, industrial SMPS, open frame adapters |
The status question on this family
Two part numbers are one letter apart and sit on opposite sides of the vendor lifecycle table. The original L6599 is marked not recommended for new designs. The L6599A is in full production and is the code to specify for a new board. A buyer who inherits a drawing with the older code will find that brokers still have stock and that the honest long term route is a change to the A revision, which is pin compatible in the same packages.
For anyone holding stock of the older part, the twin level overcurrent behaviour is worth writing down, because a stage that trips into the latched level needs a power cycle rather than an automatic restart. That is a deliberate choice for a television supply, where a repeated restart on a failed lamp is worse than a shutdown, and it is the wrong choice for a product that has to recover by itself.
Use, and the related pages
The part sits on the primary side of an LLC stage in televisions, servers, telecom rectifiers and industrial supplies. Related pages are obsolete part cross reference hub, component obsolescence management for the plan once a status changes, and power management cross reference.
Questions buyers ask on this code
The first is the difference between the A and the non A code, and it is the production status plus the improvements the revision brought, not the package. The second is the maximum frequency, which is 500 kHz and not a target: a stage that runs near that limit has very little dead time margin and needs the timing checked on the bench. The third is the bootstrap diode, which is inside the part, so the external bootstrap components that older controllers needed are gone.