Contact Us

L6562ADTR

Brand: ST
L6562ADTR is a switching regulator IC from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine L6562ADTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

L6562ADTR — Voltage Regulator by STMicroelectronics

The L6562ADTR is an STMicroelectronics voltage regulator in SOIC-8_150mil for reliable power management in embedded and industrial applications.

Part Number Decoded — Field by Field

FieldValueMeaning
L6562ADTRFull Part NumberSTMicroelectronics Voltage Regulator

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberL6562ADTR
PackageSOIC-8_150mil
TypeFixed/Adjustable Voltage Regulator
QualificationIndustrial (-40°C to +125°C)

Product Overview

The L6562ADTR is an STMicroelectronics voltage regulator in SOIC-8_150mil package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.

Key Features & Benefits

Stable Output with Built-in Protection

Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.

Wide Compatibility & Minimal External Components

Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.

Industrial Temperature Range

Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.

Target Applications

Drone & Embedded System Power Rails

Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.

Industrial & Automotive Electronics

Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.

General-Purpose Point-of-Load Regulation

Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.

Frequently Asked Questions

What is the output voltage of the L6562ADTR?

Check the specific variant. The L6562ADTR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.

What capacitors are needed for stability?

Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics L6562ADTR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.

L6562ADTR: a transition mode PFC controller with 30 microamps of start-up current

L6562ADTR is the A revision of the L6562 transition mode power factor correction controller from STMicroelectronics, in the SO-8 body, tape and reel. It holds the mains current in phase with the mains voltage on a boost stage running at the boundary between continuous and discontinuous conduction, and it does so with a start-up current of 30 microamps and a quiescent current of 2.5 milliamps. The earlier L6562 drew 70 microamps and 4 milliamps, which is the difference the A revision was made for.

The start-up current is not a small detail. It flows through the resistor chain from the rectified mains before the controller wakes up, and every microamp saved there is either a smaller loss in a high voltage resistor or a shorter start-up delay. On a 400 W adapter the difference between 70 and 30 microamps is a resistor chain that runs several hundred milliwatts cooler in standby, which is the difference between passing and missing a standby power limit.

What the A revision document states

FunctionTransition mode power factor correction controller
Start-up current30 microamps, ultra low
Quiescent current2.5 milliamps
Internal reference1 percent at 25 degrees junction
Gate driverMinus 600 to plus 800 milliamps totem pole, active pull down during undervoltage
Current senseDigital leading edge blanking on the current sense input
MultiplierProprietary, for minimum total harmonic distortion of the input current
Overvoltage protectionAdjustable and very accurate
DisableOn the error amplifier input
PackagesDIP-8 and SO-8
Package on this codeSO-8, tape and reel
Named applicationsIEC 61000-3-2 compliant supplies, adapters and chargers up to 400 W, entry level servers, electronic ballast

Transition mode, and what it costs

Transition mode means the boost inductor current is allowed to fall to zero on every cycle before the switch turns on again. That removes the reverse recovery loss of the boost diode, which is why a transition mode stage can reach efficiencies that a continuous mode stage needs a silicon carbide diode to match. The cost is a higher peak current for the same average, so the inductor and the switch carry more stress, and the power level where the trade stops working is around 300 to 400 W, which is exactly where the vendor stops naming applications.

The leading edge blanking on the current sense input is the second practical point. Without it the turn-on spike of the switch would trip the current limit on every cycle and the stage would never reach its rated power. With it the controller ignores the first few hundred nanoseconds and measures the real inductor current, and a board that shows a current limit fault at low power is usually a blanking or a gate resistor problem rather than a controller problem.

Where the part is used, and the related pages

Typical uses are the front end of an AC to DC supply that has to meet the harmonic current limit, which in practice means any lighting or computing product sold into Europe above 25 W. Related pages are power management cross reference, obsolete part cross reference hub for the transition from the non A revision, and one stop BOM sourcing.

Questions buyers ask on this code

The first is whether this part replaces the L6562 directly, and it does, pin for pin, with lower start-up and quiescent current, which is why the A revision is the one to stock. The second is whether the multiplier needs matching components, and the answer is that the input divider and the compensation network are set by the power stage and not by the controller. The third is the disable function on the error amplifier input, which is what a protection circuit uses to shut the stage down without a separate latch.