Contact Us

AM26LV31IDR

Brand: Texas Instruments
Texas Instruments AM26LV31IDR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AM26LV31IDR — Power Management & Signal Chain | Superb Automation

AM26LV31IDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The AM26LV31IDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

AM26LV31IDR: 3.3 V quad RS-422 driver, pin compatible with the 5 V part

AM26LV31IDR is the drop-in 3.3 V driver for a board that was built around a 5 V AM26C31 in a SOIC body of 16 pins. The part is a quadruple differential driver that runs from 3.3 V, switches to 32 MHz with 8 ns typical propagation and 500 ps of skew, and is offered as a pin to pin replacement for the AM26C31 and AM26LS31. Differential output is 1.5 V typical into 100 ohms, the inputs accept 5 V logic, and the dissipation is 0.3 mW maximum with no load.

Order code and package

Order codeAM26LV31IDR
Functionquad differential line driver, three-state outputs
StandardTIA/EIA-422-B and ITU recommendation V.11
Supplysingle 3.3 V rail
Replacementpin to pin for AM26C31 and AM26LS31
Logic inputsaccept 5 V levels while the supply is 3.3 V
PackageSOIC, 16 pins, 9.90 mm by 3.91 mm
TemperatureC grade 0 to 70 C, I grade as printed 45 to 85 C
Dissipation0.3 mW maximum with no load
DatasheetSLLS201 revision I, May 1995 revised April 2024
Processbipolar and CMOS combined, low power without losing speed

Electrical parameters that decide the application

Switching rate32 MHz
Propagation delay8 ns typical
Pulse skew500 ps typical
Differential output1.5 V typical into 100 ohms, against 2.6 V on the protected member of the family
Dissipation385 mW typical with all four channels switching at 32 MHz into no load
Input levels5 V compatible, which is what makes the replacement possible on a 5 V controller
Three-statecommon enable for all four drivers
Power offhigh impedance outputs
PackageSOIC 16 only, so the TSSOP and SSOP bodies of the 5 V part have no equivalent here
Temperaturethe C grade is 0 to 70 C and the I grade range is printed without its sign

Points to check before this part goes on a BOM

The temperature range for the I grade is printed as 45 to 85 C in this document, which reads as a lost minus sign. An industrial build should confirm the range with the vendor before committing, because the difference between minus 45 and plus 45 is the difference between a working outdoor product and a recalled one.

One and a half volts of differential output into 100 ohms is 15 mA, against 2.6 V and 25 mA on the protected member of the family. The pinout is the same, the swing is not, so a drop-in replacement on a long cable reduces the margin at the far receiver by roughly 40 percent.

Pin to pin compatibility with the AM26C31 covers the pin functions, not the supplies. The 5 V part runs from 5 V and this one from 3.3 V, so the replacement also removes the 5 V rail from the board, which is usually the point of the exercise.

Three hundred and eighty-five milliwatts with all four channels switching at 32 MHz and no load is the dynamic dissipation of the output stage. Into a real 100 ohm load the line current adds to it, so the figure is a floor and not a budget.

The C grade at 0 to 70 C covers a bench instrument and nothing else. A board that runs at 70 C internal ambient needs the I grade, and the printed range on that grade should be read carefully.

Only the SOIC body is offered, so a board built around the TSSOP version of the 5 V part cannot take this code at all. The replacement is a body change as well as a supply change unless the original was SOIC.

Where this order code fits

Boards replacing a 5 V driver usually gain the most from the 5 V tolerant inputs, which keep the controller side unchanged. Boards comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Is this a true drop-in for the AM26C31? The pin functions match, but the supply is 3.3 V and the differential swing is 1.5 V instead of the larger 5 V figure, so the receiver margin has to be rechecked.

Why does the datasheet print the I grade as 45 to 85 C? It reads as a lost minus sign. Confirm the range with the vendor before an industrial build relies on it.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.