A5975ADTR
Product Specifications
A5975ADTR — Voltage Regulator by STMicroelectronics
The A5975ADTR is an STMicroelectronics voltage regulator in HSOP-8EP for reliable power management in embedded and industrial applications.
Part Number Decoded — Field by Field
| Field | Value | Meaning |
|---|---|---|
| A5975ADTR | Full Part Number | STMicroelectronics Voltage Regulator |
Quick Specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Part Number | A5975ADTR |
| Package | HSOP-8EP |
| Type | Fixed/Adjustable Voltage Regulator |
| Qualification | Industrial (-40°C to +125°C) |
Product Overview
The A5975ADTR is an STMicroelectronics voltage regulator in HSOP-8EP package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.
Key Features & Benefits
Stable Output with Built-in Protection
Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.
Wide Compatibility & Minimal External Components
Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.
Industrial Temperature Range
Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.
Target Applications
Drone & Embedded System Power Rails
Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.
Industrial & Automotive Electronics
Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.
General-Purpose Point-of-Load Regulation
Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.
Frequently Asked Questions
What is the output voltage of the A5975ADTR?
Check the specific variant. The A5975ADTR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.
What capacitors are needed for stability?
Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.
What is the minimum order quantity (MOQ)?
Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.
Request a Quote
SUPERB Automation supplies genuine STMicroelectronics A5975ADTR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.
A5975ADTR: a 2.5 A step down regulator for a 12 V automotive rail
A5975ADTR is an automotive step down switching regulator in the HSOP8 body with an exposed frame, on tape and reel. It takes 4 V to 36 V in, delivers up to 2.5 A at an output set between 1.235 V and 35 V, and switches at a fixed 500 kHz. The internal switch is a P channel DMOS with 250 milliohm typical on resistance, and the exposed frame takes the junction to ambient resistance down to about 40 degrees per watt, which is the figure that makes 2.5 A possible in a small body.
The AEC-Q100 qualification is the first line of the feature list. The 4 V minimum input is the second interesting number: it is what lets the regulator keep its output alive during a cold crank, when a 12 V rail collapses to a few volts for tens of milliseconds. A part with a 6 V floor would drop out in that window and reset the load.
All figures here come from DocID018761 Rev 2, dated March 2021.
The operating window
| Function | Step down monolithic switching regulator |
| Input range | 4 V to 36 V |
| Output current | 2.5 A DC, with a minimum switch current limit of 3.1 A |
| Output voltage | Adjustable from 1.235 V to 35 V |
| Reference | 3.3 V with 2 percent tolerance printed in the feature list |
| Switching frequency | 500 kHz fixed internally, with synchronisation |
| Switch element | Internal P channel DMOS, 250 milliohm typical |
| Duty cycle | Up to 100 percent, low dropout operation |
| Light load | Zero load current operation, with an inhibit pin for zero consumption |
| Protections | Internal current limiting, thermal shutdown, feedback disconnection |
| Thermal resistance | About 40 degrees per watt junction to ambient in the HSOP8 frame |
| Qualification | AEC-Q100 |
| Package | HSOP8 with exposed frame |
Duty cycle and loss at a 12 V to 5 V conversion
From 12 V to 5 V the duty cycle is 5 divided by 12, which is 0.417. The switch conducts for that fraction of each cycle, so at 1 A the conduction loss is 0.25 ohm times 1 A squared times 0.417, about 0.10 W, and at 2 A it is about 0.42 W. Those are small numbers next to the inductor and diode losses, which is why the 40 degrees per watt frame is enough at 2 A and why the part is usually limited by the external components rather than by its own silicon.
The 3.1 A minimum switch current limit sets the peak inductor current the regulator can reach. With 2.5 A of DC output the peak sits above the average by half the ripple, so the inductor value has to keep the ripple below about 0.6 A at the worst input voltage, otherwise the limit trips before the output reaches full load. That is a component choice, not a part choice, and it is where a 2.5 A claim turns into a 1.8 A supply on a real board.
At 36 V in and 5 V out the duty cycle falls to 0.139 and the switch on time at 500 kHz is 278 ns. The minimum on time of the part has to be respected, and a build that pushes the input higher or the output lower runs into that floor. Our power management cross reference page lists the pin compatible regulators we compare when the duty cycle gets short.
What the compensation pin expects
The error amplifier is brought out on the COMP pin, so the loop compensation is external. The data sheet gives a starting network for a ceramic output capacitor, and the value changes with the output capacitance and the load range. A board that copies a reference network onto a different output capacitor value will oscillate at light load, and the symptom is a rail that looks fine on a meter and resets a processor under load steps.
Zero load current operation means the regulator does not need a minimum load to stay in regulation, which removes a dummy resistor from the board. The voltage feed forward term keeps the loop gain stable across the 4 V to 36 V input range, and it is the reason the same compensation works at both ends of the window.
Where the part is used
Automotive body and infotainment rails, cluster supplies, sensor rails and any 12 V system that needs a 5 V or 3.3 V rail at a couple of amps from a wide input. The 36 V ceiling and the 4 V floor cover load dump clamping and cold crank in one part, which is why it appears in modules that must keep running through a start event.
We supply this string for automotive builds and hold the date code and reel record for each lot. The incoming inspection plan page describes the checks at goods in, and the component lead time solutions page covers what we do when the reel is not on the shelf.
Three questions buyers ask about this string
Is the reference 3.3 V or 1.235 V? The feature list prints a 3.3 V reference with 2 percent tolerance, and the output adjustment range starts at 1.235 V. The two figures describe different nodes in the loop, and quoting the wrong one puts the output at the wrong voltage.
Can it deliver 2.5 A at 5 V from 36 V? Not continuously in a small body at high ambient. The conduction loss is small, but the switching loss at 500 kHz and 36 V is not, and the 40 degrees per watt frame has to be checked against the ambient.
Does it need an external diode? Yes, a Schottky catch diode is external, and its forward drop at the load current is part of the efficiency budget.