AM26LV31EIDR
Product Specifications
AM26LV31EIDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The AM26LV31EIDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AM26LV31EIDR: 3.3 V quad RS-422 driver with 15 kV bus protection
AM26LV31EIDR is the driver chosen when a 3.3 V board has to survive a cable fault at the connector in a SOIC body of 16 pins. The part drives four balanced pairs from a single 3.3 V supply at switching rates to 32 MHz, with 8 ns typical propagation delay and 500 ps of skew. The bus pins carry 15 kV human body model protection and 8 kV of IEC 61000-4-2 contact discharge, the outputs deliver 30 mA, and the inputs accept 5 V logic levels while the part runs from 3.3 V.
Order code and package
| Order code | AM26LV31EIDR |
| Function | quad differential line driver, three-state outputs |
| Standard | TIA/EIA-422-B and ITU recommendation V.11 |
| Supply | single 3.3 V rail |
| Logic inputs | accept 5 V levels while the supply is 3.3 V |
| Bus protection | 15 kV human body model, 8 kV IEC 61000-4-2 contact, 15 kV air gap |
| Output current | 30 mA |
| Package | SOIC, 16 pins, 9.90 mm by 3.91 mm |
| Temperature range | minus 40 to plus 85 C |
| Partial power down | outputs disabled when the supply is off |
| Datasheet | SLLS848 revision C, April 2008 revised April 2024 |
| Protection | output short circuit and glitch free power up and power down |
Electrical parameters that decide the application
| Switching rate | 32 MHz |
| Propagation delay | 8 ns typical |
| Pulse skew | 500 ps typical |
| Differential output | 2.6 V typical into a 100 ohm load |
| Rise and fall time | 5 ns typical, controlled so the pair does not radiate more than it has to |
| Output current | 30 mA, which is the drive behind the 2.6 V into 100 ohms |
| ESD on bus pins | 15 kV human body model and 8 kV contact discharge, a field connector number rather than a bench number |
| Power down | the Ioff circuit removes the output stage from the bus when the rail is off |
| Input levels | 5 V compatible, so a 5 V controller can drive a 3.3 V driver without a translator |
| Package | SOIC 16 and a VQFN 16 with thermal pad |
Points to check before this part goes on a BOM
The E suffix is the whole reason to buy this code. The plain AM26LV31 in the same family carries the standard bench level protection, while this part puts 15 kV human body model and 8 kV contact discharge on the eight bus pins, which is what a cable that leaves the enclosure needs.
Two and a half volts of differential output into 100 ohms is 25 mA of drive, and the 30 mA rating is the margin above it. A bus with two 120 ohm terminations in parallel presents 60 ohms, so the same driver delivers about 1.8 V and the receiver at the far end sees less margin than the board test showed.
Eight nanoseconds of propagation and 500 ps of skew keep a 32 MHz pair square, but the controlled 5 ns edges are what keep the emission inside a shielded enclosure test. Shortening the edges by loading the output less is a trade against the emission figure.
The inputs accept 5 V while the supply is 3.3 V, which removes a level translator from the interface between an older controller and a new transceiver. The reverse direction is not offered: a 3.3 V driver cannot swing a 5 V receiver input above its threshold reliably.
Ioff disables the outputs when the rail is off, so a board that is powered down does not load a live bus. The feature is worth checking on a second source, because the same pinout without Ioff turns an unpowered node into a resistive load across the pair.
Output short circuit protection is specified for a fault to ground or to the rail, not for a sustained short between the two lines of a pair. A cable crushed across the pair is a thermal event that the protection limits rather than removes.
Where this order code fits
Boards that need IEC level protection at the connector start here rather than at the unprotected member of the family. Boards comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and boards replacing a part that has gone end of life start from the Defense Grade Components page.
Questions buyers ask
What is the difference against the AM26LV31? The bus pin protection: 15 kV human body model and 8 kV IEC contact discharge here, against the standard level on the plain part. The pinout is the same.
Can it drive a 60 ohm bus? It can, but the differential output falls to about 1.8 V, so the margin at the far receiver has to be recalculated rather than assumed from the 100 ohm figure.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.