Contact Us

L78L05ABUTR

Brand: ST
L78L05ABUTR is a linear voltage regulator from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine L78L05ABUTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
quote now

Product Specifications

L78L05ABUTR — Voltage Regulator by STMicroelectronics

The L78L05ABUTR is an STMicroelectronics voltage regulator in SOT-89(SOT-89-3) for reliable power management in embedded and industrial applications.

Part Number Decoded — Field by Field

FieldValueMeaning
L78L05ABUTRFull Part NumberSTMicroelectronics Voltage Regulator

Quick Specifications

ParameterValue
ManufacturerSTMicroelectronics
Part NumberL78L05ABUTR
PackageSOT-89(SOT-89-3)
TypeFixed/Adjustable Voltage Regulator
QualificationIndustrial (-40°C to +125°C)

Product Overview

The L78L05ABUTR is an STMicroelectronics voltage regulator in SOT-89(SOT-89-3) package, providing reliable, stable output voltage for embedded systems, IoT devices, and industrial applications.

Key Features & Benefits

Stable Output with Built-in Protection

Features internal thermal shutdown, current limiting, and safe operating area (SOA) protection — ensuring reliable output regulation even under fault conditions, short circuits, and high ambient temperatures typical in enclosed electronics.

Wide Compatibility & Minimal External Components

Requires only input and output capacitors for stable operation, minimizing BOM count and PCB area. Compatible with ceramic, tantalum, and electrolytic output capacitors for design flexibility.

Industrial Temperature Range

Rated for −40°C to +125°C junction temperature, suitable for outdoor drone applications, automotive under-hood electronics, and industrial control systems exposed to wide thermal swings.

Target Applications

Drone & Embedded System Power Rails

Provides regulated voltage for MCU core/IO supplies, sensor analog references, and communication module power in drone flight controllers, IoT nodes, and portable electronics.

Industrial & Automotive Electronics

Widely used in PLCs, sensor transmitters, motor control boards, and automotive ECUs where a robust, well-protected voltage regulator is essential for system reliability.

General-Purpose Point-of-Load Regulation

Serves as a simple, cost-effective point-of-load regulator for powering individual ICs, analog circuits, and mixed-signal subsystems from higher-voltage system rails.

Frequently Asked Questions

What is the output voltage of the L78L05ABUTR?

Check the specific variant. The L78L05ABUTR is available in multiple fixed output voltages (typically 3.3V, 5V, 12V) or as an adjustable version. Refer to the datasheet for exact specifications.

What capacitors are needed for stability?

Typically 0.33µF on input and 0.1µF on output minimum. For optimal transient response, 10µF output capacitance is recommended. Refer to the datasheet for ESR stability requirements if using ceramic capacitors.

What is the minimum order quantity (MOQ)?

Contact SUPERB Automation for a tailored quote. We support quantities from prototype to full production volumes with competitive lead times.

Request a Quote

SUPERB Automation supplies genuine STMicroelectronics L78L05ABUTR with full traceability. Contact us with your target quantity — we'll respond with a quotation within 24 hours.

L78L05ABUTR: a 100 mA 5 V regulator in the A grade, SOT-89, tape and reel

L78L05ABUTR is the 5 V member of the L78L three terminal positive regulator family from STMicroelectronics, in the SOT-89 body, supplied on tape and reel. It holds 100 mA of output current when the tab has copper to work with, needs no external components beyond the usual input and output capacitors, and carries internal current limiting and thermal shutdown, so a short on the load pulls the output down instead of destroying the part.

The letters in the code carry the purchase decision. The AB block is the grade specified from minus 40 to plus 125 degrees junction temperature, and the A tolerance band is plus or minus 4 percent, which at 5 V is a window of 4.8 to 5.2 V. The U is the SOT-89 package and TR is tape and reel. The same die is sold as L78L05ACUTR with the wider C band and the narrower temperature range, and buyers who do not read the middle letters end up comparing two prices for two different guarantees.

Every figure below comes from the vendor document DS0424, revision 30, dated August 2024, which covers the whole L78L family across 3.3, 5, 6, 8, 9, 10, 12, 15, 18 and 24 V. The document prints a separate electrical table for each voltage and each grade, so a row quoted for the C grade is not a specification for the AB part.

The numbers that decide whether it fits

FunctionThree terminal fixed positive regulator, internal current limit and thermal shutdown
Output voltage5 V, plus or minus 4 percent in the A grade, 4.8 to 5.2 V
Output current100 mA, with adequate heat sinking
Maximum input30 V for the 5 V member, rising to 35 V and 40 V for the 12 V and 18 V members
Dropout voltage2 V typical at 40 mA in the vendor table
Quiescent current6 mA maximum at 25 degrees, 5.5 mA at 125 degrees, C grade table
Supply voltage rejection49 dB typical at 120 Hz, C grade table
Output noise40 microvolts typical, 10 Hz to 100 kHz
Test capacitors0.33 microfarad input, 0.1 microfarad output
PackagesTO-92, SO-8, SOT-89
Junction to ambient55 degrees per watt for SOT-89 and SO-8 with 6 square centimetres of copper, 200 degrees per watt for TO-92
Junction range, AB grademinus 40 to plus 125 degrees
Storage rangeminus 65 to plus 150 degrees

Thermal arithmetic before the order goes out

The part is limited by heat, not by current. Feeding 12 V into a 5 V output at 50 mA puts 350 mW into the die. On a SOT-89 pad with 6 square centimetres of copper at 55 degrees per watt that is a rise of about 19 degrees above ambient, which is comfortable. The same 350 mW in a TO-92 at 200 degrees per watt is a rise of 70 degrees, and a 70 degree ambient then leaves nothing. This is why the SOT-89 code and the TO-92 code are not interchangeable on a board that draws real current, even though the die inside is the same.

The 2 V dropout figure sets the input floor. A 5 V output needs at least 7 V at the input to stay in regulation at 40 mA, and more if the load is at the 100 mA limit. Any rail that sits at 6.3 V is already outside the guaranteed window, and the output will follow the input down rather than hold 5 V.

Where it turns up in a build

These parts land on the analogue side of a board: a local 5 V rail for a current sense amplifier, a bias supply for a relay driver, or a post regulator behind a switching stage where the switching noise has to be cleaned before it reaches a sensor. In radio front ends the same part feeds the logic of a synthesizer that cannot tolerate the ripple of the main buck. Related pages for the sourcing side are power management cross reference for the pin compatible alternatives, pin to pin cross reference for the footprint check, and one stop BOM sourcing for putting the whole rail on one order.

Questions buyers ask on this code

The first is always the grade. A C grade part at a lower price will hold 5 V only inside plus or minus 8 percent, which at the extremes is 4.6 V and 5.4 V. A 5 V logic rail that also feeds an ADC reference cannot take the top of that window. The second is the package suffix. U is SOT-89 and the SOT-89 pin order is not the same as the SO-8, so a substitution between the two needs a board change and not just a BOM change. The third is the reel. TR is tape and reel and the reel quantity is set by the package, so a line that consumes 200 pieces a week should be buying the reel and not cut tape.