Contact Us

STM32F205RGT6

Brand: ST
ST STM32F205RGT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F205RGT6 — MCU & Embedded Processors | Superb Automation

STM32F205RGT6

ST — MCU & Embedded Processors

Product Overview

The STM32F205RGT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F205RGT6: 1 Mbyte, 120 MHz and a High Speed USB Port in 64 Pins

STM32F205RGT6 is the top density of the STM32F205 line in the 64 pin LQFP body: 1 Mbyte of flash, 128 Kbytes of system SRAM plus 4 Kbytes of backup SRAM, a Cortex-M3 at 120 MHz with the adaptive real time accelerator giving 150 DMIPS, and a peripheral set that includes two USB OTG ports, two CAN controllers, three converters each running at 2 MSPS and a camera interface absent on this subfamily. The G in the code is the 1 Mbyte density and the R is the 64 pin body.

What the accelerator does at 120 MHz

Running from flash at 120 MHz would normally cost several wait states and a lower effective instruction rate. The accelerator on this line adds an instruction cache, a data cache and a branch cache in front of the flash interface, so straight line code executes with no wait states from the cache and only the misses pay. The published figure is 150 DMIPS at 120 MHz, which is the same 1.25 DMIPS per MHz as the F103 parts, so the gain over a 72 MHz device is the clock ratio and nothing else. Where the firmware has large loops that cross cache lines, measured throughput is below that ratio, and the first place it shows is in an interrupt handler that touches a big table.

Values at a glance

ParameterValueNote
Core and clockCortex-M3, 120 MHz, 150 DMIPSAdaptive real time accelerator, MPU
Flash, SRAM1 Mbyte, 128 Kbytes plus 4 Kbytes backup512 bytes of one time programmable memory
PackageLQFP64, 10 by 10 mmGPIO count drops to 51 in this body
Supply1.8 to 3.6 VLower minimum than the F103 line, useful on a 1.8 V rail
ADC, DAC3 converters, 12 bit, 16 channels; 2 DAC channels2 MSPS each, 6 MSPS in triple interleaved mode
USBOTG high speed and OTG full speedHigh speed needs an external ULPI PHY
Communication3 I2C, 3 SPI, 2 I2S, 4 USART, 2 UART, 2 CANFifteen interfaces, USART at 7.5 Mbit/s, SPI at 30 Mbit/s
TemperatureMinus 40 to plus 85 CCode 7 reaches 105 C ambient, junction limit 125 C

The high speed port is not self contained

The OTG high speed controller on this line uses a ULPI interface, so a 480 Mbit link needs an external PHY on the board plus its own supply and reference. The full speed OTG port has an on chip PHY and only needs the connector and the 5 V switch. Products that quote high speed USB in a specification often find after the first prototype that the PHY, its 60 MHz reference and the extra board area cost more than the microcontroller choice was meant to save, and full speed operation at 12 Mbit is enough for a data logger in most cases.

1 Mbyte in a 64 pin body

The combination is unusual and deliberate: a small package with the largest memory in the line, for products whose firmware is large but whose I/O count is modest, such as a protocol converter with several stacks compiled in. The catch is the 51 pin budget, which has to cover the debug port, the crystal, the USB pair, the CAN pair and the network interface if one is added. A microcontroller cross reference against the V and Z bodies, an one stop BOM that carries the PHY and its reference alongside the part, and a sourcing position on the 1 Mbyte density are what a build plan needs before the first order.

Common questions

Is the backup SRAM retained in standby? Yes, the 4 Kbytes are supplied from VBAT and survive standby and the main supply going away, which is what makes it usable for a retained counter or a calibration block.

Can the three converters really reach 6 MSPS? Only in triple interleaved mode with a single input distributed to all three, which trades channels for rate. Each converter alone runs at 2 MSPS.

Does the part have Ethernet? No. The MAC belongs to the STM32F207 codes. The F205 line keeps the FSMC and the LCD interface but not the network MAC.