TPS82671SIPR
Product Specifications
TPS82671SIPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS82671SIPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS82671SIPR: a 600 mA step down supply that arrives with its inductor and capacitors inside a 2.3 mm by 2.9 mm package
TPS82671SIPR is a complete 600 mA step down converter in a MicroSiP package, with the switching regulator, the inductor and the input and output capacitors already inside in a uSiP (SIP) body of 8 pins. It runs from 2.3 V to 4.8 V, switches at a regulated 5.5 MHz, holds 17 microamp of quiescent current, and delivers a fixed 1.8 V on this string with plus or minus 2 per cent total DC accuracy. The package is under 1 mm tall and the whole solution fits in less than 6.7 square millimetres.
Order code and package
| TPS82671SIPR | uSiP (SIP) body, 8 pads, 2.30 mm by 2.90 mm and 1.0 mm tall, 3000 pieces on a large reel, tin silver copper finish, moisture level 2 at 260 C for one year, marking RA, fixed 1.8 V output with spread spectrum |
| TPS82671SIPT | the same body on a 250 piece small reel, which is the string a prototype run orders |
| TPS826711SIPR | the 1.8 V member with low PFM output ripple, marking YW, the option when the light load ripple has to stay small |
| Temperature columns | the addendum carries both a minus 40 C to 85 C column and a minus 40 C to 125 C column, and the row has to be read per string rather than assumed |
| Finish | tin silver copper with moisture level 2 at 260 C for one year, so the reel has a floor life that has to be tracked after the bag is opened |
| Packing | 3000 pieces on the large reel and 250 on the small reel, both in tape wide enough for an 8 pad package |
Electrical parameters that decide the application
| Input voltage | 2.3 V to 4.8 V, which is one lithium cell with margin and a 3.3 V rail with tolerance |
| Output current | 600 mA continuous, set by the regulator inside the package rather than by an external switch |
| Output voltage | 1.8 V fixed on this string, with plus or minus 2 per cent total DC accuracy including the load and line terms |
| Switching frequency | 5.5 MHz regulated, high enough that the inductor inside the package is small and the output ripple stays low |
| Quiescent current | 17 microamp typical in power save mode, which is what makes the part usable on a battery that sits idle for weeks |
| Efficiency | 90 per cent at 5.5 MHz, measured at the load point the curve in the document uses |
| Ripple rejection | 35 dB or better from 1 kHz to 10 kHz, which is why the part is used to replace a linear regulator on a noisy rail |
| Start up | internal soft start with a 120 microsecond ramp, so no external capacitor is needed to tame the inrush |
| Modes | automatic PFM and PWM switching, so the light load efficiency and the heavy load ripple are both handled without a mode pin |
| Spread spectrum | PWM frequency dithering on this string, which spreads the switching energy and lowers the peak in an emissions scan |
| Profile | under 1.0 mm tall, which is the number that decides whether the part fits behind a camera module or a display |
| Solution size | under 6.7 square millimetres with no external components beyond the two pads the package needs |
Family variants and how they differ
| Output options | 1.86 V, 1.8 V, 1.6 V, 1.5 V, 1.26 V, 1.25 V, 1.225 V, 1.2 V, 1.1 V, 1.05 V, 1.95 V and 2.1 V appear across the family, each as its own order string |
| TPS82670 | 1.86 V, marking YK, the member that sits just above the 1.8 V string |
| TPS82672 | 1.5 V, marking WD, for a rail that has to sit below the 1.8 V family |
| TPS82673 | 1.26 V, marking YL, with low PFM ripple |
| TPS82674 and TPS82677 | 1.2 V members with spread spectrum, marking SW and SK |
| TPS826716 | 1.6 V with output capacitor discharge, marking GS, the option when the rail has to come down quickly at power off |
Points to check before this part goes on a BOM
Nothing external is required. The inductor and both capacitors are inside the package, so a working rail needs no components beyond the supply decoupling on the input side.
The package is the limit on current. 600 mA is set by the regulator and the inductor inside the body, and there is no version of this part that can be pushed higher by adding copper.
Moisture level 2 is not the same as unlimited floor life. The reel has one year at 260 C after the bag is opened, so a line that keeps part of a reel for a later build has to track the exposure rather than assume it is safe.
The fixed output is the point. There is no divider and no external feedback node, so the accuracy is the device accuracy and the board cannot move the rail by picking different resistors.
The 5.5 MHz switching frequency keeps the ripple small but limits the input voltage. Above 4.8 V the part is outside its operating range, so a 5 V rail needs a different member of the family.
Why a module replaces a linear regulator here
A 1.8 V rail at 300 mA from a 3.6 V battery dissipates half a watt in a linear regulator, which is more than a small package can pass to the board. The same rail from this module runs at about 90 per cent efficiency, so the heat falls by an order of magnitude and the battery life follows.
The trade is the switching ripple. A linear regulator has almost none, and the module has the 5.5 MHz residue plus the PFM pulses at light load. On a rail that feeds an analog front end the low ripple member is the right choice, and on a digital rail the standard member is enough.
The other trade is the inductor. It is inside the package and it is the reason the part cannot be pushed past 600 mA, but it is also the reason the output ripple stays inside a few millivolts without a second filter stage. On a rail that feeds a radio or an analog front end the high switching frequency and the small inductor are an advantage, because the residue sits above the band the load cares about and the filter that follows can be a single capacitor.
Where this order code fits
It fits a wearable, a camera module or a portable instrument, where a 1.8 V rail at a few hundred milliamps has to come from a single cell in a space under a millimetre tall. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Does the module need an external inductor or capacitor? No. The regulator, the inductor and the input and output capacitors are inside the package, and the total solution is under 6.7 square millimetres with nothing added.
What is the difference between the 1.8 V members? The TPS82671 has spread spectrum on the PWM side, and the TPS826711 has low PFM output ripple. The first lowers the emissions peak, the second keeps the light load ripple small, and the choice follows the sensitivity of the load.
Can it work from a 5 V rail? Not this string. The input range is 2.3 V to 4.8 V, so a 5 V rail is outside the operating window and a different converter is needed.
Is the 600 mA rating a peak or a continuous figure? It is the continuous output current the regulator and the inductor inside the package are rated for, and it does not rise with better board copper.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.