Contact Us

TPS63050RMWR

Brand: Texas Instruments
Texas Instruments TPS63050RMWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS63050RMWR — Power Management & Signal Chain | Superb Automation

TPS63050RMWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS63050RMWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS63050RMWR: single inductor buck boost, 1 A switches, adjustable output, in a 12 pin HotRod QFN

TPS63050RMWR is a buck boost converter that keeps its output in regulation while the input crosses above and below it, which is the case on a lithium cell whose voltage drifts through the rail it is feeding in a VQFN-HR body of 12 pins. It accepts 2.5 V to 5.5 V in, delivers up to 1 A in buck mode and 500 mA in boost, and switches at 2.5 MHz typical from a 0.8 V feedback reference. Quiescent current is under 60 uA, shutdown current is 0.1 uA typical, and the part adds a power good output, an adjustable input current limit and a soft start set by one capacitor.

Order code and package

TPS63050RMWR12 pin HotRod QFN (RMW), 2.50 mm by 2.50 mm, 3000 pieces on a large reel, marking F630, moisture level 1 unlimited
TPS63050RMWTsame body and silicon, 250 pieces on a small reel
TPS63050YFFR12 ball chip scale body, 1.56 mm by 1.16 mm, 3000 pieces on a large reel, the same die in a smaller footprint
TPS63051RMWRfixed 3.3 V member of the family, 3000 pieces on a large reel, marking F631
Operating temperatureminus 40 C to plus 125 C junction, every row of the addendum

Electrical parameters that decide the application

Input voltage2.5 V to 5.5 V, with the converter crossing between modes without a disturbance on the output
Output voltage2.5 V to 5.5 V, adjustable on the TPS63050 and fixed on the TPS63051
Output current1 A in buck mode, 500 mA in boost mode at 3.3 V out from 2.5 V in
Switch current1 A typical maximum average current in the switches, which is the real limit rather than the load figure
Switching frequency2.5 MHz typical, fixed in PWM mode
Quiescent currentunder 60 uA typical in power save mode, 65 uA maximum in the electrical table
Shutdown current0.1 uA typical and 1 uA maximum with the enable pin low
Feedback voltage0.8 V on the adjustable member, with 1 per cent accuracy in PWM mode
Power goodopen drain, releases when the output passes 95 per cent of nominal, sinks up to 0.1 mA
Soft startset by a capacitor on the SS pin, charged at about 1 uA to a 1.3 V threshold

The pins that make it configurable

ILIM0 and ILIM1two pins that select the input current limit in four steps, including an inrush setting for a discharged output capacitor
PFM/PWM pinselects automatic power save mode or forced fixed frequency operation, which is how a low noise rail is obtained
SS pinone capacitor sets the ramp, and the vendor curve gives the capacitance against the start time at 10 uF of output capacitance
Power goodopen drain with a 0.1 mA sink limit, so the pull up resistor has to be sized for the load it drives
Load disconnectthe output is disconnected in shutdown, so a battery is not drained through the inductor path
Two bodiesHotRod QFN at 2.5 mm square and a chip scale body at 1.56 mm by 1.16 mm, same pins and same behaviour

Points to check before this part goes on a BOM

The mode crossing is the feature that sells this part and the one that is hardest to prove on a bench. As the input falls through the output voltage the converter moves from buck to boost without a step, and the output stays within its accuracy window. On a lithium cell discharging from 4.2 V into a 3.3 V rail, that crossing happens somewhere in the middle of the discharge curve, and a converter that glitches there produces a reset the customer sees as a random failure.

The 1 A switch limit is not the same as a 1 A output. In buck mode the switch current is lower than the output current, so 1 A of load is inside the limit. In boost mode the switch carries the input current, which is higher than the output current, so 500 mA of output at 3.3 V from 2.5 V in is already near the switch ceiling. The vendor states both figures and the mode they belong to.

The quiescent current of 60 uA is the power save mode figure and it depends on the PFM/PWM pin. Tying that pin high forces fixed frequency and the quiescent current rises, which is the trade for a clean spectrum. A product that has to pass an emissions test at light load uses forced PWM and pays the standby current, while a product that has to last a year on a coin cell uses power save and lives with the variable frequency.

The soft start is configured by a capacitor and the vendor curve is drawn for 10 uF of output capacitance. Doubling the capacitance doubles the time for the same capacitor, and the current available to charge the output is limited by the inrush setting on the two current limit pins. A rail that starts into 100 uF with the smallest inrush setting will take a long time and may never reach regulation before the enable signal is withdrawn.

The power good output releases at 95 per cent of nominal and sinks only 0.1 mA, which is enough for a logic input and not enough for an LED. It is also only valid while the converter is enabled, so a supervisor that reads it during shutdown sees whatever the pull up gives, which is usually high on a rail that is still charged. The pin is a start up indicator rather than a supply monitor.

The shutdown current of 0.1 uA typical with load disconnect is what makes the part usable on a battery that sits idle. Without the disconnect the inductor and the body diode would form a path from the battery to the load even with the converter off, and a 3.7 V cell would leak through whatever sits on the output rail. The disconnect is internal, so there is no external FET to add.

Two bodies with the same die and the same pinout give a program a way to trade area against thermal performance. The chip scale body is 1.56 mm by 1.16 mm and the HotRod QFN is 2.5 mm square, and at 1 A of buck current the larger body is the one that keeps the junction in check on a board with limited copper. A board that swaps one for the other without changing the copper will run hotter.

Where this order code fits

It powers 3.3 V or 3.0 V loads from a single lithium cell, a two cell alkaline pack or a supercapacitor, in handheld instruments, wireless modules and battery products where the supply voltage drifts through the rail during normal use. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

How much current is available at 3.3 V out? Up to 1 A while the input is above the output, and about 500 mA when the input falls to 2.5 V and the converter is boosting. The switch current limit is the ceiling in both modes.

Does the output glitch when the input crosses the output voltage? No. The converter changes mode seamlessly, which is the point of the part. The transient at the crossing is small enough to stay inside the accuracy window.

How is the start up time set? By one capacitor on the SS pin, charged at about 1 uA to 1.3 V. The vendor curve gives the value against time for 10 uF of output capacitance.

What does the power good pin indicate? That the output has passed 95 per cent of nominal. It sinks 0.1 mA, so it drives a logic input and needs a pull up resistor.

Can the switching frequency be changed? No. It is fixed at 2.5 MHz. The PFM/PWM pin chooses between power save mode and forced fixed frequency operation at that rate.

Is the battery disconnected in shutdown? Yes, the load is disconnected internally, with 0.1 uA typical shutdown current. No external FET is needed.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.