Contact Us

TPS3305-33DR

Brand: Texas Instruments
Texas Instruments TPS3305-33DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3305-33DR — Power Management & Signal Chain | Superb Automation

TPS3305-33DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3305-33DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3305-33DR: dual supply supervisor with watchdog and a fixed 200 ms delay in an 8 pin SOIC body

TPS3305-33DR is a dual voltage supervisor that watches a 5 V and a 3.3 V rail, holds a processor in reset until both are valid, and trips if the watchdog input stops toggling in a SOIC body of 8 pins. It runs from 2.7 V to 6 V, draws 40 uA maximum, and monitors two rails against fixed thresholds with 20 mV of hysteresis. The reset delay is 200 ms and needs no external capacitor. The watchdog trips after 1.6 s without a transition on its input. Both a low going and a high going reset output are provided, and the output is defined from 1.1 V of supply.

Order code and package

TPS3305-33DR8 pin SOIC (D), 2500 pieces on a large reel, nickel palladium gold finish, moisture level 1 unlimited, minus 40 C to plus 85 C junction
TPS3305-33D8 pin SOIC, 75 pieces in a tube, the quantity a repair line orders
TPS3305-33DGNR8 pin HVSSOP (DGN), 2500 pieces on a large reel, 2.14 W of dissipation against 725 mW for the SOIC
TPS3305-33DGN8 pin HVSSOP, 80 pieces in a tube
Other membersTPS3305-18 for a 3.3 V and 1.8 V pair and TPS3305-25 for a 3.3 V and 2.5 V pair, both on the same body and pinout
Second row per codethe addendum repeats each string with an .A suffix and the same quantity, so the suffix does not change the packing

Electrical parameters that decide the application

Supply voltage2.7 V to 6 V, with the supply pin also being the reference for the internal 1.25 V band gap
Sense one5.0 V rail, negative going threshold 4.55 V typical with 20 mV of hysteresis
Sense two3.3 V rail, negative going threshold 2.93 V typical with 20 mV of hysteresis
Supply current40 uA maximum, measured with both sense inputs at the supply voltage
Reset delay140 ms minimum, 200 ms typical and 280 ms maximum, generated internally with no capacitor
Watchdog time out1.1 s minimum, 1.6 s typical and 2.3 s maximum, retriggered by a transition on the watchdog input while both rails are above their thresholds
Reset outputsone active low and one active high, both driven from the same internal state, defined from 1.1 V of supply
Manual resetan input that forces reset when pulled low, with a 100 microsecond minimum pulse width
Propagation1 microsecond to 5 microseconds from a sense input crossing to a reset change, and 200 ns to 500 ns from the manual reset input
Output drive2 mA at 0.4 V on the low side and 2 mA at supply minus 0.4 V on the high side at 3.3 V
Dissipation725 mW in the SOIC body at 25 C, derating at 5.8 mW per degree, against 2.14 W in the HVSSOP
Temperatureminus 40 C to plus 85 C junction, which is narrower than the industrial parts around it

Which rails this member watches

TPS3305-335.0 V on sense one at a 4.55 V threshold and 3.3 V on sense two at 2.93 V, the 5 V and 3.3 V pair common in mixed signal boards
TPS3305-183.3 V on sense one and 1.8 V on sense two, at 2.93 V and 1.68 V
TPS3305-253.3 V on sense one and 2.5 V on sense two, at 2.93 V and 2.25 V
Threshold tolerancethe thresholds are specified at 0 C to 85 C and again at minus 40 C to 85 C, and the two rows differ by a few millivolts
Watchdog inputcan be tied to the supply or left open if the watchdog is not wanted, and the document's truth table shows reset released only when both rails are above their thresholds and the manual reset is high
Both polaritiesthe two reset outputs are separate pins, so a board can drive an active low processor reset and an active high peripheral enable from the same part

Points to check before this part goes on a BOM

This member supervises 5.0 V and 3.3 V, not 3.3 V and 1.8 V. That is the single most common mistake with the family, because the suffix reads like the output voltage of the part rather than the pair of rails it watches. The ordering information table pairs TPS3305-33 with a 5.0 V sense one threshold of 4.55 V and a 3.3 V sense two threshold of 2.93 V. A board that expects a 3.3 V core monitor from the 33 suffix will release reset at the wrong point on both rails.

The thresholds are 90 per cent of the nominal rail and they carry only 20 mV of hysteresis. Forty millivolts of hysteresis on a 4.55 V threshold is under 1 per cent, which is tight for a rail with any ripple. A 5 V rail that sags under load can cross the threshold repeatedly and produce a reset pulse train rather than a single clean reset. The manual reset input and a small amount of bulk capacitance on the monitored rail are the usual answers, and the part itself offers no way to widen the band.

The reset delay of 200 ms is fixed and needs no capacitor, which is the main reason to choose this family over a discrete supervisor plus a comparator. The tolerance on that delay is 140 ms to 280 ms, which is wide in percentage terms and irrelevant in practice, because a processor only needs the delay to be longer than its own power supply ramp. What the part does not do is hold reset for a programmable time after the rail falls, so a brownout shorter than the delay may not produce a reset at all.

The watchdog is a separate timer with a 1.6 s nominal window and a 1.1 s to 2.3 s spread. A processor that toggles its watchdog pin every 500 ms is safe across the whole spread. A processor that toggles every 1.0 s is inside the window on the typical part and outside it on a part whose window has drifted down to 1.1 s, which produces resets that appear only on some boards and only over temperature. The safe rule is to toggle at least twice as fast as the minimum window.

The two reset outputs are driven from the same internal state, and both are valid from 1.1 V of supply. That matters at power down, where many supervisors let their outputs float as the supply collapses and the processor sees a reset line that is neither high nor low. Here the outputs stay defined down to 1.1 V, which is below the point where most processors stop executing reliably, so the reset assertion happens while the processor can still act on it.

The dissipation rating differs by a factor of three between the two packages. The SOIC body handles 725 mW at 25 C and derates at 5.8 mW per degree, which leaves 377 mW at 85 C. The HVSSOP handles 2.14 W and leaves 1.11 W at the same temperature. A 40 uA supervisor dissipates almost nothing itself, so the difference only matters in a hot enclosure where the ambient is already near the limit, but the derating curve is the number to check before putting either body in a sealed box.

The 85 C junction limit is the tightest specification in the table and it excludes a good deal of industrial work. A board that has to run at 85 C ambient with any self heating needs a different part. The 40 uA supply current and the 2.7 V to 6 V range suggest a battery or a 5 V bus, which usually means a benign thermal environment, and that is the application the part was built for rather than a hot cabinet.

Where this order code fits

It sits on mixed signal boards that carry a 5 V analogue rail and a 3.3 V digital rail, typical of industrial controllers, telecom line cards and instrument front ends where both rails have to be valid before a processor is released. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

Which rails does the -33 member watch? 5.0 V on sense one with a 4.55 V threshold and 3.3 V on sense two with a 2.93 V threshold. The suffix names the pair, not a single output voltage.

Can the reset delay be changed? No. It is 200 ms nominal with a 140 ms to 280 ms spread, generated internally and not adjustable.

What happens if the watchdog is not used? The input can be tied to the supply or left open, and the reset then depends only on the two sense inputs and the manual reset pin.

What is the watchdog window? 1.6 s typical, with a 1.1 s to 2.3 s spread. A processor should toggle at least twice as fast as the 1.1 s minimum.

Does it provide both reset polarities? Yes. One active low and one active high output, driven from the same internal state and both defined from 1.1 V of supply.

Which package should a hot board use? The HVSSOP, which dissipates 2.14 W at 25 C against 725 mW for the SOIC, and still leaves 1.11 W at 85 C.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Date Code Management page sets out the checks that keep a substitute from failing on the bench.