Contact Us

TPS79301DBVR

Brand: Texas Instruments
Texas Instruments TPS79301DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS79301DBVR — Power Management & Signal Chain | Superb Automation

TPS79301DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS79301DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS79301DBVR: 200 mA adjustable RF LDO with 112 mV dropout in a 6 pin SOT-23 body

TPS79301DBVR is an adjustable low dropout regulator aimed at RF and analogue rails, where the noise and the rejection decide the choice and the dropout is already small in a SOT-23 body of 6 pins. It runs from 2.7 V to 5.5 V, supplies 200 mA, and sets any output between 1.22 V and 5.5 V from a 1.2246 V reference. Dropout is 112 mV typical and 200 mV maximum at 200 mA, and the part has been through two silicon generations that differ in noise, ground current and the presence of a noise reduction pin.

Order code and package

TPS79301DBVR6 pin SOT-23 (DBV), 3000 pieces on a large reel, marking PGVI, moisture level 1 unlimited
TPS79301DBVTsame body and silicon, 250 pieces on a small reel
TPS79301DBVRG4same part with the green material declaration, 3000 pieces on a large reel
Feedback reference1.2246 V typical, divider on the FB pin, 30.1 kOhm is the vendor starting value for the lower resistor
Operating temperatureminus 40 C to plus 125 C junction across all rows

Electrical parameters that decide the application

Input voltage2.7 V to 5.5 V, with the enable pin rated across the same span
Output voltage1.22 V to 5.5 V adjustable, limited at the top by the input minus dropout
Output current200 mA maximum continuous
Dropout voltage112 mV typical and 200 mV maximum at 200 mA, 120 mV typical on the older silicon
Output noise33 uVRMS in the electrical table over a 100 Hz to 100 kHz band, while the front page quotes 55 uVRMS on the legacy chip and 69 uVRMS on the new chip
Rejection65 dB at 200 mA on the new chip, falling with frequency but still useful well into the megahertz range
Ground pin current170 to 220 uA on the legacy chip, 250 uA to 1 mA on the new chip, which is the largest single difference between the two generations
Current limitabout 400 mA foldback on the legacy chip, so the output voltage falls rather than the current rising without bound
Enable threshold1.7 V high, 0.425 V low on the new chip, with the pin drawing under 1 uA
Output capacitor2.2 uF ceramic minimum, stable across the usual ESR window

Two silicon generations under one part number

Noise reduction pinpresent on the legacy chip as pin 4, where an external capacitor filters the bandgap and lowers noise further. On the new chip the same pin is a no connect
Ground currentthree to four times higher on the new chip, which matters on a battery rail that stays enabled
Start up50 us on the legacy chip against 500 us on the new chip, so a rail that sequenced against the old timing needs a re check
Noisethe new chip is quieter in the 55 to 69 uVRMS front page figure and the legacy chip is quieter once its noise reduction capacitor is fitted
MarkingPGVI on the DBV body, which is how the two generations are told apart on a reel
Fixed membersthe same document covers the fixed 1.8 V to 4.75 V versions, which are separate order codes and not adjustable

Points to check before this part goes on a BOM

One part number, two silicon generations, and the differences land in exactly the parameters a sensitive rail cares about. The new chip has no noise reduction pin, draws three to four times the ground current and starts up ten times slower, but it is the quieter of the two by the front page figures. A board qualified against the legacy chip and re ordered two years later can arrive with the new one, so the noise, the start up time and the quiescent drain all have to be checked against the marking on the reel rather than the part number.

The 33 uVRMS in the electrical table and the 55 and 69 uVRMS on the front page are not a contradiction, they are different bandwidths and different conditions. The table figure is over 100 Hz to 100 kHz; the front page figures cover the wider 10 Hz to 100 kHz band that includes the 1/f region. Quoting the smaller number in a comparison table against a competitor is the kind of thing that gets caught in a technical review.

The dropout of 112 mV typical at 200 mA is genuinely small for a 200 mA part, and it is what allows a 3.3 V rail to be held from a 3.5 V supply. The maximum of 200 mV is the number to use for a worst case budget, and at 125 C the curve in the document is closer to the maximum than the typical. A 3.3 V rail fed from a 3.4 V rail is inside the typical and outside the maximum, which is a specification that will pass on the bench and fail in the chamber.

The foldback current limit around 400 mA is twice the rated current, which is generous for a 200 mA part and is why the part survives a short at 5 V. It also means the output can deliver a brief surge well above 200 mA, useful for a load with a capacitive inrush, but not something to rely on for a continuous load. Anything drawing more than 200 mA steadily is outside the thermal envelope of a 6 pin SOT-23.

The reference is 1.2246 V, which is close enough to 1.25 V that engineers who copy a 1.25 V divider from another regulator end up 2 per cent low. The vendor starting value of 30.1 kOhm for the lower resistor is chosen to keep the divider current small relative to the 200 mA load while staying above the leakage of the feedback pin. A 100 kOhm divider works and adds noise; a 10 kOhm divider is quiet and wastes current.

The enable pin has a 1.7 V high threshold and draws under 1 uA, so it can be driven from a 1.8 V logic rail without a level shifter. It is also rated to the full 5.5 V input, which means an always on rail can tie it to the input directly. Leaving it floating is not specified and is the most common cause of a rail that comes up on some boards and not others.

The 2.2 uF ceramic output capacitor is a minimum for stability rather than a suggestion. The part is stable with a small ceramic because the internal compensation is set for it, and fitting a 10 uF electrolytic instead is the fastest way to make an oscillating regulator. Tantalum and aluminium parts with high ESR are outside the stable window entirely.

Where this order code fits

It powers RF front end bias, voltage controlled oscillator supply pins, low noise amplifiers and analogue blocks in handheld radios and instrumentation, where a 3.3 V rail has to come from a battery or a 5 V bus with only a few hundred millivolts to spare. Teams comparing it with a neighbouring part start from our RF Component Sourcing page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Why does the same part number behave differently on two boards? Because two silicon generations share it. The legacy chip has a noise reduction pin, 170 to 220 uA of ground current and a 50 us start up; the new chip has a no connect on that pin, 250 uA to 1 mA and 500 us. The marking on the body tells them apart.

Is 200 mA enough for an RF amplifier bias rail? For a small signal stage, yes. For a power stage drawing more than 200 mA the thermal limit of the SOT-23 body is reached before the current limit, so the rail needs a larger package rather than this part.

Can the output be set to 1.2 V? The reference is 1.2246 V, so 1.22 V is the floor. Anything below that needs a different regulator with a lower reference.

Does it need the noise reduction capacitor? Only the legacy chip has the pin, and the capacitor lowers noise further. The new chip has no such pin, so there is nothing to fit and nothing to lose.

What is the dropout at 100 mA? Lower than the 112 mV typical at full load; the curve falls with current. Use the 200 mA row for a worst case budget and the curve for anything lighter.

Is it stable with a ceramic output capacitor? Yes, 2.2 uF ceramic is the specified minimum. High ESR electrolytic parts are outside the stable window.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Power Management Cross Reference page sets out the checks that keep a substitute from failing on the bench.