Contact Us

TPS61046YFFR

Brand: Texas Instruments
Texas Instruments TPS61046YFFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61046YFFR — Power Management & Signal Chain | Superb Automation

TPS61046YFFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61046YFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61046YFFR: 28 V boost with a 900 mA switch, 12 V default output, in a 6 ball chip scale body

TPS61046YFFR is a boost converter that lifts a single cell or a two cell alkaline pack to as much as 28 V with the diode, the isolation switch and the feedback divider all inside the package in a DSBGA body of 6 pins. It takes 1.8 V to 5.5 V in, produces 4.5 V to 28 V out, and switches at 1 MHz so a 10 uH inductor is enough. Tying the feedback pin to the input selects a fixed 12 V output with three external components. The peak switch current is 900 mA typical, the shutdown current is 0.5 uA, and the body is a 6 ball chip scale package measuring 0.80 mm by 1.20 mm.

Order code and package

TPS61046YFFR6 ball DSBGA (YFF), 0.80 mm by 1.20 mm, 3000 pieces on a large reel, tin silver copper balls, moisture level 1 unlimited, marking SJS, addendum prints minus 40 C to plus 150 C in the temperature column
TPS61046YFFTsame body, 250 pieces on a small reel, the prototype quantity
BallsVIN, SW, VOUT, FB, EN and GND, with the switch and the output on adjacent balls so the inductor and the output capacitor can sit on the same side
Fixed 12 V optionconnect FB to VIN and the internal divider sets 12 V, which is the configuration the front page uses to count three external components
Second row per codethe addendum repeats both strings with an .A suffix and the same quantity, so the suffix changes the row rather than the packing

Electrical parameters that decide the application

Input voltage1.8 V to 5.5 V operating, with a lockout that trips near 1.55 V falling and needs 1.8 V maximum to release when rising
Output voltage4.5 V to 28 V, set by an external divider or fixed at 12 V when the feedback pin is tied to the input
12 V accuracy11.7 V to 12.3 V with the internal divider across 0 C to 125 C, which is 2.5 per cent total
Reference0.795 V to 0.811 V with a 0.803 V typical, measured in pulse frequency mode
Peak switch current600 mA minimum and 900 mA typical, which is the ceiling on how much power can move through a given inductor
Switching frequency850 kHz to 1250 kHz with a 1050 kHz typical at 3.6 V in and 12 V out
Quiescent current110 uA typical with the converter enabled and no load, and 0.5 uA in shutdown, rising to 0.8 uA at 85 C
Overvoltage protection29.2 V to 30.4 V, which is the clamp that protects the 28 V ceiling rather than the regulation loop itself
Isolation switch850 milliohm on resistance, open in shutdown, which is what separates the output from the input when the enable pin is low
Soft start10 ms internal ramp, which is the reason a 22 uF output can be charged from a single cell without collapsing the input
Protectionoutput short circuit with foldback, output overvoltage, thermal shutdown at 150 C junction and recovery near 130 C

What the fixed and adjustable settings change

FB tied to VINthe internal divider sets 12 V, and the external network is only the inductor, the input capacitor and the output capacitor
FB on a dividerany output between 4.5 V and 28 V, with the 0.803 V reference setting the ratio and the divider current kept well above the 200 nA leakage of the pin
Output below 4.5 Vnot supported by this part, because the switch and the isolation path need headroom. A 3.3 V rail from one cell is a different family
Power save modeentered automatically at light load, where the part bursts at the pulse frequency reference instead of switching continuously
Continuous modethe converter runs at 1 MHz whenever the load keeps the inductor current above zero, which is where the 85 per cent efficiency at 3.6 V in and 12 V out is measured
Inductor choicethe 900 mA switch limit sets the saturation requirement, and a 10 uH part with a saturation above 1.2 A covers the whole input range

Points to check before this part goes on a BOM

The 28 V output ceiling and the 30.4 V overvoltage clamp are two different numbers and both matter. The regulation loop can hold any output up to 28 V. The clamp fires between 29.2 V and 30.4 V if the feedback divider opens or the load disappears, and it protects the switch and the internal diode rather than the load. A board that runs a 28 V rail at the top of the range is inside the regulation window and only a few volts below the point where the clamp fires, so a transient that overshoots on load release has nowhere to go except into the output capacitor.

The peak switch current is 900 mA typical with a 600 mA minimum. That window, not the output voltage, sets the power the converter can move. At 3.6 V in and 12 V out the ideal conversion ratio gives about 270 mA of output at 900 mA of switch current, less the losses, and the minimum figure of 600 mA cuts that by a third. A load that needs 250 mA at 12 V from a nearly empty cell is outside what this part can promise even though the front page describes a 28 V converter.

The 12 V default removes the divider but also removes the ability to trim. With the feedback pin tied to the input, the output is 11.7 V to 12.3 V over temperature, which is 2.5 per cent. That is fine for a PMOLED bias or a sensor module supply and not fine for anything that needs 1 per cent. The divider version uses the 0.803 V reference and inherits the tolerance of the two resistors, so a 1 per cent pair gets close to the same 2 per cent total rather than beating it.

The shutdown current of 0.5 uA is the headline figure, and the isolation switch is what makes it real. With the enable pin low, the internal switch between the input and the output opens, so the load cannot leak back through the inductor and the body diode of a conventional boost. That is why this part can sit on a battery rail without a series load switch. The same isolation is what allows a true disconnect rather than a converter that merely stops switching while the output stays tied to the input through the diode.

The 10 ms soft start is long for a converter of this size and it is deliberate. A 22 uF output charged to 12 V from a single cell needs 264 uC, and at 900 mA of switch current the charging current available is limited. A shorter ramp would pull the input down through the battery impedance and trip the lockout on a nearly empty cell. The cost is that a 10 ms ramp is visible to a system that expects its rail inside a millisecond, so the enable signal has to be sequenced accordingly.

The quiescent current of 110 uA with the converter enabled and no load is worth checking against the application. This is not a standby part. A product that leaves the 12 V rail on while the rest of the board sleeps burns 110 uA continuously, which over a month is about 80 mAh from a single cell. The right pattern is to gate the enable pin from a processor wake signal so the converter is off, and rely on the 0.5 uA shutdown row rather than on the no load figure.

The addendum prints the operating temperature as minus 40 C to plus 150 C while the electrical table is specified from minus 40 C to 125 C junction. Those two rows are not in conflict, they answer different questions. The addendum column is the storage and handling classification of the packaged part, and the electrical table is where the part is guaranteed to meet its numbers. A board that runs the junction to 140 C is outside the specified range even though the reel label says 150 C.

Where this order code fits

It sits in PMOLED panel bias, wearable sensor supplies, portable medical instruments and any small module that needs a 12 V to 28 V rail from a single lithium cell or two alkaline cells. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

How do I get 12 V out with the fewest parts? Tie the feedback pin to the input pin. The internal divider sets 12 V and the external network is the inductor plus two capacitors.

What is the maximum output current at 12 V? About 270 mA at 3.6 V in with a typical switch limit of 900 mA, and roughly a third less in the worst case where the switch limit sits at its 600 mA minimum.

Is the output disconnected in shutdown? Yes. The isolation switch opens and the shutdown current is 0.5 uA, so the load does not leak back through the inductor.

Can it produce 3.3 V from one cell? No. The minimum output in regulation is 4.5 V, because the switch and the isolation path need headroom above the input.

What protects the output if the feedback divider opens? The overvoltage clamp fires between 29.2 V and 30.4 V and stops the switch, which sits above the 28 V regulation ceiling on purpose.

Does the part need an external Schottky diode? No. The power diode and the isolation switch are inside the package, which is why the 12 V configuration needs only three external components.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.