VBL2303
Product Specifications
VBL2303
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL2303 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL2303: a minus 30 V, 3 milliohm P channel switch for battery rails
The VBL2303 is a P channel trench MOSFET in the TO-263 outline, printed at minus 30 V from drain to source with a plus or minus 20 V gate. The summary gives 3 milliohm at a minus 10 V gate with minus 20 A flowing, a continuous drain current of minus 100 A with the case at 25 C and minus 80 A with the case at 70 C, a pulsed rating of minus 300 A, a continuous source drain diode current of minus 110 A and a single pulse avalanche energy of 281 mJ. The junction is rated to 175 C, the package dissipates 425 W with the case at 25 C, and the part is RoHS compliant.
This is a high current P channel, which is an unusual thing to find. Most P channel parts stop at a few amps because the cell resistance is high, and the ones that reach 100 A do it with a very large die in a big package. The 3 milliohm channel in a TO-263 is the electrical equivalent of a good N channel from ten years ago, and it exists for the one job a P channel does better than anything else: a high side battery switch that needs no charge pump.
The ratings a buyer checks first
| Drain to source voltage | minus 30 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at minus 10 V gate, minus 20 A | 3 milliohm typical |
| Continuous drain current, case at 25 C and 70 C | minus 100 A and minus 80 A |
| Continuous drain current, ambient at 25 C and 70 C | minus 39 A and minus 33 A |
| Pulsed drain current | minus 300 A |
| Continuous source drain diode current | minus 110 A with the case at 25 C |
| Single pulse avalanche energy and current | 281 mJ from 0.1 mH at 75 A |
| Maximum power dissipation, case at 25 C and 70 C | 425 W and 282 W |
| Gate threshold at minus 250 microamp | minus 2 V minimum, minus 3 V typical, minus 4 V maximum |
| Gate source leakage at plus or minus 20 V | plus or minus 100 nA maximum |
| Total gate charge at minus 20 V and minus 110 A | 205 nC typical, 315 nC maximum |
| Gate source and gate drain charge | 58 and 52 nC typical |
| Total gate resistance at 1 MHz | 4.0 ohm typical |
| Input, output and reverse transfer capacitance | 9000, 1610 and 1100 pF |
| Turn on delay and rise time | 25 and 20 ns typical |
| Turn off delay and fall time | 110 and 30 ns typical |
| Body diode forward drop at minus 20 A | minus 0.8 V typical, minus 1.5 V maximum |
| Body diode reverse recovery time and charge | 20 ns and 130 nC typical |
| Operating junction and storage range | minus 55 to plus 175 C |
Reading the electrical table instead of the front page
The three current rows on this sheet tell a buyer almost everything. Minus 100 A is a case temperature figure, minus 39 A is an ambient figure on a board, and the difference is a factor of two and a half. At 39 A the channel dissipates 4.6 W, which a TO-263 on a plane can carry; at 100 A it dissipates 30 W, which needs the tab held near 25 C. A battery disconnect that carries 60 A continuous is therefore a heatsink job, and a buyer who reads only the front page will not plan for one.
The gate charge is large: 205 nC typical at a minus 10 V gate with 52 nC of gate drain charge, on a part with 9000 pF of input capacitance. That is the cost of a 3 milliohm P channel die. Driving it from a divider and a zener, which is the usual P channel arrangement, gives a slow turn on and a long linear region, and at 50 A that linear region is where the part dies. A proper gate driver or a dedicated high side controller is not optional at this current.
The reverse transfer capacitance of 1100 pF is high, and on a P channel high side switch it couples the drain edge into the gate. With a divider holding the gate, a fast rising drain voltage pushes the gate up through that capacitance and can turn the part off or on at the wrong moment. The 110 ns turn off delay against a 30 ns fall suggests the vendor expects a gate driven hard, not a resistor.
The body diode is worth noting because of its size: minus 110 A of continuous diode current and a minus 0.8 V drop at minus 20 A. In a battery switch the diode conducts whenever the load is connected and the switch is off, which is the reverse polarity condition, and 110 A of capability means the part can hold a reverse connection without a fuse. That is a real protection function rather than a parasitic.
Where a minus 30 V P channel part earns its place
The first use is a high side battery disconnect on a single cell or a two cell pack, where the switch sits in the positive rail and the gate is pulled to ground through a resistor and a small N channel. The 100 A case current covers a power tool or a drone pack, and the 175 C junction covers the stall interval before the controller reacts.
The second use is reverse polarity protection on a 12 V or 24 V input, where the P channel conducts in the forward direction and blocks when the input is reversed. The minus 110 A diode rating means the body diode holds the reverse current until the fuse opens, which is what a robust input stage needs.
The third use is a load switch for a motor or a heater on a 24 V rail, where the switch has to be fully on for long intervals and the loss at 30 A is 2.7 W. The 175 C junction and the 281 mJ avalanche rating cover the inductive kick of the harness without a freewheel diode in the return path.
Sourcing notes and the second source question
A 3 milliohm P channel at minus 30 V is a narrow product. Two parts that print the same resistance can differ by a factor of three in gate charge, and on a 100 A switch the gate charge sets the switching loss and the drive requirement, so a substitute with a larger charge needs a different driver and a different board. The power management cross reference keeps the charge and the capacitance beside the resistance for that comparison.
The pin order of a TO-263 P channel is standard, but the tab is the drain and the drain is the switched rail, so the copper under the tab is at the battery potential and the thermal path has to be isolated from the case if the case is grounded. The pin to pin cross reference records the tab connection with the electrical data, because a substitute with a different tab polarity is a short circuit rather than a second source.
Because the part is used in battery products, the date code and the storage conditions matter as much as the electrical data. Our date code management page covers how we keep a battery grade part traceable from the reel to the pack.
Questions we answer before a reel is booked
The first question is the gate drive. At 315 nC maximum, a resistor divider cannot turn the part on fast enough for a 50 A load, and the part will spend milliseconds in the linear region on every power up. A dedicated driver with a 1 A peak output is the responsible choice, and we ask what drives the gate before quoting a current.
The second question is the ambient current. The 39 A ambient row is the one that applies to a board mounted part, and the 100 A figure needs a tab held at 25 C. A battery pack that carries 60 A continuous needs a metal tab and a thermal interface, and the pack assembly should be checked before the part is qualified.
The third question is the reverse condition. With the body diode rated to minus 110 A, a reversed battery will conduct through the diode until the fuse opens, and the diode drop of minus 0.8 V at minus 20 A becomes minus 80 W of dissipation at minus 100 A. The part survives that for the fuse time, and the fuse has to be chosen with that interval in mind.