Contact Us

HXC50020

Brand: Hisiwell
Hisiwell HXC50020 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXC50020 — Discrete & Power Semiconductors | Superb Automation

HXC50020

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXC50020 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXC50020: a part whose page says 450 W and whose index row says 850 W

The HXC50020 is listed on the index at 850 W, 915 MHz, 16 dB of gain, 64 per cent efficiency and 40 V. The product page describes the same part number as a 450 W internally matched device for ISM applications including RF energy at 915 MHz, in Class AB, B or C, for CW and pulsed signals. The two figures are 2.76 dB apart, which is nearly a factor of two, and this is the largest disagreement between a page and an index row on the HXC50 shelf.

Neither figure can be dismissed. A vendor that lists a 450 W page for an 850 W index row usually means that the page text is the older description and the index was updated after a die change, or that the index carries the saturated output while the page carries the linear rating. The difference between a saturated figure and a linear figure on a 40 V LDMOS part at 915 MHz is normally 1 to 2 dB, not 2.76 dB, so the more likely reading is that the page text is older than the index row.

The page does not resolve it and neither does the index. The page states both figures in its first table row, treats the index row as the number a system should be built against, and marks the discrepancy as a question for the vendor. That is the only honest position until the vendor answers, and it is the reason this row carries a lower confidence than its neighbours.

The HXC50020 rows as the vendor publishes them

Part classLDMOS RF power transistor, internally matched, ISM
Output, index row850 W
Output, product page450 W
Output in dBm, calculated59.29 dBm at 850 W, 56.53 dBm at 450 W
Difference between the two rows, calculated2.76 dB
Frequency, index row and page915 MHz
Drain rail, index row40 V
Modes, pageClass AB, B or C, CW and pulsed
Gain, index row16 dB
Drain efficiency, index row64 per cent
Drive at 16 dB for 850 W, calculated21.35 W, or 43.29 dBm
Drive at 16 dB for 450 W, calculated11.30 W, or 40.53 dBm
Load voltage at 850 W into 50 ohm, calculated206.2 V rms, 291.5 V peak
Peak against the 40 V rail, calculated7.29 times
Load voltage at a 2 to 1 mismatch, calculated583 V peak
Load voltage at a 3 to 1 mismatch, calculated875 V peak
DC input at 850 W and 64 per cent, calculated1328 W, 33.20 A at 40 V
Heat to remove at 850 W and 64 per cent, calculated478 W
DC input at 450 W and 64 per cent, calculated703 W, 17.58 A at 40 V
Heat to remove at 450 W and 64 per cent, calculated253 W
Thermal resistance, junction to caseNot published for this row
Breakdown voltage and capacitance setNot published for this row
Test fixture and board materialNot published for this row
Document link on the pagePoints at the site root and serves nothing
Applications listed on the pageISM RF energy, 915 MHz heating
Orderable addendumNone published
Packing quantity and moisture levelNot published

What 850 W or 450 W on 40 V asks of the rail, and why the gap is not academic

At 850 W into 50 ohm the peak is 291.5 V, 7.29 times the 40 V rail, and at 450 W it is 212 V, 5.31 times. Both ratios need a matched push pull device, and both are inside what a 40 V LDMOS pair can do, so the rail does not tell the two readings apart. The mismatch case does: 583 V at 2 to 1 and 875 V at 3 to 1 for the 850 W reading, against 424 V and 636 V for the 450 W reading.

The supply is where the gap becomes a purchasing decision. At 850 W and 64 per cent efficiency the DC input is 1328 W, 33.2 A at 40 V, and at 450 W it is 703 W, 17.6 A. A 33 A bus at 40 V needs a bus bar, a large bulk capacitance at the device and a supply that holds its voltage on the pulse; a 17.6 A bus is a different product. A buyer who sizes the supply on the page and receives a part that runs at the index figure will find the rail sagging and the protection tripping, and the fault will look like the supply rather than the part.

For a CW ISM applicator at 915 MHz, the practical approach is to build for 450 W, which both sources agree the part can do, and treat 850 W as the ceiling to be confirmed. That way the supply, the heat sink and the applicator are all correct for the conservative reading, and if the vendor confirms the higher figure the product can be turned up without a rebuild.

Thermal: 478 W against 253 W and one missing number

At 64 per cent efficiency the heat is 478 W at the index reading and 253 W at the page reading. With no published thermal resistance, bound it from the shelf: a 1 kW part on 50 V publishes 0.2 degrees per watt and a 700 W part on 40 V is normally near 0.22. At 0.2 degrees per watt and 478 W the rise is 96 degrees, so at an 85 degree case the junction is near 181 degrees against a 225 degree limit. At 253 W the rise is 51 degrees and the junction near 136 degrees.

Both are inside the limit, but the difference in heat sink is a factor of two. A product built for 450 W has a heat sink and a fan sized for 253 W of heat; turning the same hardware up to 850 W doubles the heat and the junction goes from comfortable to 44 degrees from the limit. That is exactly the kind of change that is invisible in a datasheet comparison and obvious in a thermal camera.

The flange at this power is a mechanical component in its own right. 478 W through a ceramic flange needs a flat, thick mounting surface with a controlled interface, and the mounting screws have to be torqued to the vendor's figure because the pressure distribution across the flange is what the thermal resistance assumes.

Drive, gain and a 2.76 dB question about the driver

At 16 dB of gain the drive is 21.35 W for the 850 W reading and 11.30 W for the 450 W reading. That is the same 2.76 dB gap in the driver, and it decides whether a 10 W driver stage is enough or whether a 25 W stage is needed. A buyer who chooses the 10 W driver on the strength of the page and receives a part that needs 21 W will see a stage that reaches 450 W and stops, and the diagnosis will take a week.

The safe route is to specify the driver on the index figure, 21.35 W, and to accept that the driver runs 2.8 dB below its capability if the page figure is the real one. Running a driver below its ceiling costs a little efficiency and no reliability, while running it at its ceiling to reach a rating it cannot reach costs a rework of the driver.

The 16 dB gain is the highest on the 915 MHz group, which makes this the easiest of the three rows to drive per watt. If the wattage question is settled at 450 W, the gain means the total chain gain is 16 dB plus the driver's own gain, which allows a two stage product where the 700 W row would need three.

Where the HXC50020 sits on the shelf

The 915 MHz group has the 300 W part on 28 V, the 700 W part on 40 V with 15 dB and 68 per cent, and this row with 16 dB and 64 per cent. In decibels 450 W to 700 W is 1.91 dB, 700 W to 850 W is 0.84 dB, and 450 W to 850 W is 2.76 dB. So the group has two readings of the top rung and only one of them is a clean step from the 700 W part.

Read as a choice, this row is the one for a 915 MHz ISM product that needs the highest output on the shelf and can accept a wattage that has to be confirmed with the vendor. A buyer who needs a number he can hold the vendor to takes the 700 W part below it, which has the same rail, the same band and a 68 per cent efficiency figure; a buyer who needs to stay on 28 V takes the 300 W part.

Before the purchase order goes out

Two procurement points. The page and the index disagree by 2.76 dB, so the purchase order has to name a figure and the vendor has to confirm it in writing, and the incoming route for a part whose documents do not agree is on the incoming inspection plan page. Buyers comparing 850 W ISM parts at 915 MHz should start from the RF power transistor cross reference and compare on the mismatch case rather than on the headline, and the sourcing side of a high power ISM bill of materials, including the combiner and the circulator, is covered on the RF component sourcing page.