HXC50132
Product Specifications
HXC50132
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC50132 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC50132: 150 W single ended on 50 V, matched from 700 MHz to 1.5 GHz
The HXC50132 is a 150 W device at 1 dB compression, single ended, on a 50 V rail, internally matched for use anywhere inside 700 to 1500 MHz. The product page names the two sockets it is aimed at, avionics at 960 to 1215 MHz and L band at 1200 to 1400 MHz, and states that it supports CW, pulsed and modulated signals at either saturated or linear operation. The index row gives it 150 W, 0.9 to 1.5 GHz, 15 dB of gain and 55 per cent efficiency.
The band differs between the two sources: the page says 700 to 1500 MHz and the index says 900 to 1500 MHz. That is a 200 MHz disagreement at the bottom of the band, and it is the kind of thing that decides whether a part fits a 960 MHz avionics socket with margin or sits right at the edge. The page states both, and a buyer should treat 900 MHz as the guarantee and 700 MHz as a claim to be measured.
The 150 W figure is quoted at 1 dB compression rather than as a saturated output, which is a stronger statement for a linear application. A part that holds 150 W at 1 dB compression has more available in saturation, and in a modulated signal the compression point is the number that sets the linearity budget. The document link on the page points at the site root and serves nothing, so the compression figure is the only rated number available and everything else is index data plus arithmetic.
The HXC50132 rows as the vendor publishes them
| Part class | LDMOS RF power transistor, internally matched, single ended |
| Output, page | 150 W at 1 dB compression |
| Output, index row | 150 W |
| Output in dBm, calculated | 51.76 dBm |
| Frequency range, page | 700 to 1500 MHz |
| Frequency range, index row | 900 to 1500 MHz |
| Named applications, page | Avionics 960 to 1215 MHz, L band 1200 to 1400 MHz |
| Drain rail | 50 V |
| Modes, page | CW, pulsed and modulated, saturated or linear |
| Gain, index row | 15 dB |
| Drain efficiency, index row | 55 per cent |
| Drive at 15 dB, calculated | 4.74 W, or 36.76 dBm |
| Load voltage at 150 W into 50 ohm, calculated | 86.6 V rms, 122.5 V peak |
| Peak against the 50 V rail, calculated | 2.45 times |
| Load voltage at a 2 to 1 mismatch, calculated | 245 V peak |
| Load voltage at a 3 to 1 mismatch, calculated | 367 V peak |
| DC input at 55 per cent, calculated | 273 W, 5.45 A at 50 V |
| Heat to remove at 55 per cent, calculated | 123 W |
| DC input at 45 per cent, calculated | 333 W, 6.67 A at 50 V |
| Heat to remove at 45 per cent, calculated | 183 W |
| Thermal resistance, junction to case | Not published for this row |
| Breakdown voltage and capacitance set | Not published for this row |
| Test fixture and board material | Not published for this row |
| Document link on the page | Points at the site root and serves nothing |
| Orderable addendum | None published |
| Packing quantity and moisture level | Not published |
What 150 W single ended on 50 V asks of the rail and the load
150 W into 50 ohm is 86.6 V rms and 122.5 V peak, 2.45 times a 50 V rail. A single ended part does not split the load line the way a pair does, so the drain has to swing the whole 122.5 V and the breakdown voltage matters more here than on a push pull row of the same power. The page publishes no breakdown figure, which is the largest gap in this specification: without it the margin cannot be checked, and on a single ended 150 W part the margin is the thing that decides whether the part survives a mismatch.
The mismatch case reaches 245 V at 2 to 1 and 367 V at 3 to 1. On a single ended device a 3 to 1 load is a serious event, and the output network has to be built for it regardless of what the die can take. That is the reason a 150 W L band product normally has a circulator or an isolator after the stage: the cost is 0.3 to 0.5 dB and the alternative is a part that fails on the first antenna fault.
The current is 5.45 A at 55 per cent efficiency and 6.67 A at 45 per cent. On a 50 V rail that is a manageable bus and it is why the part is attractive for airborne and ground based L band equipment where the 50 V rail is already there. At 960 to 1215 MHz the wavelength is short enough that the output network is small, which keeps the loss at this power within reason.
Thermal: 123 W of heat with no published resistance
At 55 per cent efficiency the heat is 123 W and at 45 per cent it is 183 W. There is no thermal resistance published for this row, so bound it from the shelf: a 1 kW part publishes 0.2 degrees per watt, a 500 W part is normally near 0.3, and a 150 W single ended part normally sits near 0.6 to 0.8. At 0.7 degrees per watt and 123 W the rise is 86 degrees, so at an 85 degree case the junction is near 171 degrees against a 225 degree limit. At 183 W of heat the rise is 128 degrees and the junction near 213 degrees, which is close to the limit.
That last number is the one to act on. A product that runs at 45 per cent efficiency, which is what a modulated signal at 8 dB of backoff will do, has almost no thermal margin on a 0.7 degrees per watt flange. Either the flange is held below 85 degrees, which means a real heat sink and forced air, or the part is run below 150 W in the linear case. The arithmetic is easy to repeat with the vendor's own figure once it is obtained.
The single ended topology also puts the heat in one die rather than two, so the local heat flux at the flange is twice what a pair at the same power would show. That makes the interface material and the flange flatness more critical than the total heat figure suggests.
Drive, gain and 15 dB at L band
15 dB of gain means the drive for 150 W is 4.74 W, or 36.76 dBm, which is a real driver stage and not a small one. On a single ended part the input match is internal, so the driver sees a defined load across the band, which is the benefit that justifies the matched part at this power.
15 dB is 4 dB below the 70 W pair on the same shelf and 8 dB below the 10 W part. Gain falls with power at a fixed rail, and at 150 W on 50 V the input capacitance and the internal matching loss account for most of the difference. A three stage chain of 10 W, 150 W is 38 dB of net gain, which is a workable budget for a single band product without a fourth stage.
The band claim of 700 to 1500 MHz against the index range of 900 to 1500 MHz should be settled by a sweep. A matched part that holds 15 dB at 960 MHz will not hold it at 700 MHz, and the avionics socket at 960 to 1215 MHz sits comfortably inside the index range, so the practical answer is that the part fits the named application and the wider claim is unmeasured.
Where the HXC50132 sits on the shelf
The same 0.9 to 1.5 GHz region of the shelf has the 250 W part at 0.96 to 1.2 GHz on 32 V with 14 dB and 55 per cent, the 300 W and 500 W pulse parts at 1.2 to 1.4 GHz, and the 150 W part at 1.2 to 1.4 GHz on 50 V with 14 dB and 55 per cent. In decibels 150 W to 250 W is 2.22 dB and 150 W to 300 W is 3.01 dB.
Read as a choice, this row is the one for a 150 W L band or avionics socket on 50 V where a single ended matched part keeps the board simple and the compression point is the rating that matters. A buyer who needs 250 W takes the 0.96 to 1.2 GHz part on 32 V and gives up 2.2 dB of rail headroom; a buyer who needs 300 to 500 W in pulse takes the 1.2 to 1.4 GHz rows and moves to a pulse only product.
Before the purchase order goes out
Two procurement points. No document is reachable for this row, so the breakdown voltage, the thermal resistance and the fixture have to be requested in writing, and the incoming route for a part arriving with no published document is on the incoming inspection plan page. Buyers comparing 150 W L band parts should start from the RF power transistor cross reference and compare single ended against push pull on the mismatch case rather than on wattage, because a single ended part at 150 W carries a harder load line than a pair at the same output. A bill of materials with the driver, the isolator and the passives on it can be placed through the one stop RF supply route.