Contact Us

HXC50069

Brand: Hisiwell
Hisiwell HXC50069 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXC50069 — Discrete & Power Semiconductors | Superb Automation

HXC50069

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXC50069 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXC50069: 300 W matched from 700 to 1000 MHz, and two wattages on one part number

The HXC50069 is an internally matched LDMOS device filed for ISM work from 700 to 1000 MHz including RF energy at 915 MHz, on a 28 V rail, in Class AB, B or C, supporting both CW and pulsed signals. The product page calls it a 300 W part. The index row calls it 270 W with 15 dB of gain and 65 per cent efficiency. The two figures are 0.46 dB apart, which is one rung of a ladder and not a rounding error, so the page states both and treats the index row as the number a system should be built against.

The gap is normal on this shelf and it has a cause. A vendor page often quotes the saturated output of a device in a tuned fixture, while the index table quotes a guaranteed or nominal figure that a buyer can hold the vendor to. A 300 W saturated part that is sold as 270 W is a part with 0.46 dB of headroom, which is exactly what a pulse application needs when the pulse width and the duty cycle are not fixed.

The other thing the page makes clear is the band. 700 to 1000 MHz covers the 915 MHz ISM allocation with room on both sides, and matched at both ports means the board does not carry a tuned network. At 915 MHz, a band that is 26 MHz wide, a matched part covers the requirement and the applicator becomes a matter of the cavity rather than the amplifier.

The HXC50069 rows as the vendor publishes them

Part classLDMOS RF power transistor, internally matched, ISM and RF energy
Output, product page300 W
Output, index row270 W
Output in dBm, calculated54.77 dBm at 300 W, 54.31 dBm at 270 W
Difference between the two rows, calculated0.46 dB
Frequency range, page and index700 to 1000 MHz, centred on 915 MHz
Drain rail, index row28 V
Mode, pageClass AB, B or C, CW and pulsed
Gain, index row15 dB
Drain efficiency, index row65 per cent
Drive at 15 dB for 300 W, calculated9.49 W, or 39.77 dBm
Drive at 15 dB for 270 W, calculated8.54 W, or 39.31 dBm
Load voltage at 300 W into 50 ohm, calculated122.5 V rms, 173.2 V peak
Peak against the 28 V rail, calculated6.19 times
Load voltage at a 2 to 1 mismatch, calculated346 V peak
Load voltage at a 3 to 1 mismatch, calculated520 V peak
DC input at 300 W and 65 per cent, calculated462 W, 16.48 A at 28 V
Heat to remove at 300 W and 65 per cent, calculated162 W
DC input at 270 W and 65 per cent, calculated415 W, 14.83 A at 28 V
Heat to remove at 270 W and 65 per cent, calculated145 W
Thermal resistance, junction to caseNot published for this row
Breakdown voltage and capacitance setNot published for this row
Test fixture and board materialNot published for this row
Document link on the pagePoints at the site root and serves nothing
Applications listed on the pageISM RF energy, 915 MHz heating and plasma
Orderable addendumNone published

What 300 W on 28 V asks of the rail, and why the current is the story

300 W into 50 ohm is 122.5 V rms and 173.2 V peak, which is 6.19 times a 28 V rail. On 28 V that ratio is only possible because the part is matched and push pull, with each side swinging past twice the rail and the internal combiner summing the halves. The 28 V rail keeps the voltage low and the current high: 16.5 A at 65 per cent efficiency, against 9.2 A if the same power were built on a 50 V rail.

That current decides the supply and the board. A 16.5 A bus at 28 V with a pulse requirement needs bulk capacitance at the device, and the capacitance has to be close, because at 915 MHz the loop inductance between the capacitor and the drain is part of the matching network whether the buyer intends it or not. On a matched part the external capacitors are the first thing that can spoil the internal match, so the vendor's recommended decoupling is not optional.

The mismatch case is worth a second look because ISM loads move. At a 2 to 1 load the peak reaches 346 V and at 3 to 1 it reaches 520 V. On a 28 V rail an engineer may think in tens of volts; the load side is in hundreds. The capacitors, the connector and the applicator feed all see those peaks, and the failure mode in a 915 MHz heating system is usually the feed rather than the die.

Thermal: 162 W of heat with no published resistance

At 65 per cent efficiency and 300 W the heat is 162 W. There is no thermal resistance published for this row, so bound it from the shelf: a 1 kW part publishes 0.2 degrees per watt, a 70 W part 0.7, and a 300 W matched part normally sits near 0.3. At 0.3 the rise is 49 degrees, so at an 85 degree case the junction is near 134 degrees against a 225 degree limit. At 0.4 the rise is 65 degrees and the junction near 150 degrees.

Both bounds are inside the limit, which means the part is thermally viable on a reasonable flange and the risk sits in the assembly rather than the die. On a matched part the flange is the only thermal path, so the interface material and the mounting torque are part of the electrical performance as well as the thermal one: a poor interface raises the case temperature and shifts the match at the same time.

The 0.46 dB between 300 W and 270 W is also a thermal question. A system built at 300 W out runs 12 per cent more heat than the same system at 270 W, and if the heat sink was sized on the index row the margin is gone. Size the heat sink on the higher of the two figures if the product intends to use the saturated output.

Drive, gain and the 15 dB that is low for this shelf

15 dB of gain means the drive for 300 W is 9.5 W, which is a substantial driver for a single stage and is the reason a 915 MHz 300 W product is usually a three stage chain. On the same shelf the 70 W pair gives 19 dB and the 10 W part 23 dB, so gain falls as power rises, which is the normal pattern for LDMOS at a fixed rail.

The matched input is what makes 15 dB usable. An unmatched 300 W part at 915 MHz would present an input impedance that changes across the band and a gain that could swing 2 dB, so the driver would need its own equalisation. With both ports matched the gain is flat enough that the driver can be a single broadband stage.

The band is 700 to 1000 MHz, which is 3.1 dB of bandwidth in octave terms and is wide for a matched part. If the requirement is the whole band at full power the buyer should ask for a sweep rather than a single point, because a matched network that holds 300 W at 915 MHz will not necessarily hold it at 700 MHz.

Where the HXC50069 sits on the shelf

The 915 MHz group has three members: this 270 to 300 W part on 28 V, a 700 W part on 40 V with 15 dB and 68 per cent, and an 850 W part on 40 V with 16 dB and 64 per cent. The step from 300 W to 700 W is 3.68 dB and from 700 W to 850 W is 0.84 dB, so a requirement for 500 W has no exact rung and has to be met by combining or by running a larger part below its rating.

Read as a choice, this row is the one for a 915 MHz ISM product at 300 W where a 28 V rail is fixed by the rest of the system, and where a matched device removes the output network from the board. A buyer who can move to 40 V takes the 700 W part and gets 3.68 dB more for a rail change; a buyer who needs a published document takes the 1 kW part at 50 V on the HF shelf, which is a different band but the only row nearby with a full fixture and thermal table.

Before the purchase order goes out

Two procurement points. The wattage on the page and the wattage on the index differ, so the purchase order should name which figure the part is being bought against, and the incoming route for that kind of ambiguity is on the incoming inspection plan page. And the document link on the page serves nothing, so ask the vendor for the thermal resistance and the fixture in writing; buyers comparing this row against competing 300 W ISM parts should start from the RF power transistor cross reference. A mixed ISM bill of materials with the driver and the passives on it can be placed through the one stop RF supply route.