HXC50013
Product Specifications
HXC50013
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC50013 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC50013: 500 W matched at 433 MHz, and the document that is not there
The HXC50013 is a 500 W capable, internally matched LDMOS device on a 50 V rail, filed for 433 MHz RF energy and ISM work, usable in CW and in pulse. The index row gives it 500 W, a 433 MHz centre, 21 dB of gain, 74 per cent efficiency and 50 V. The product page describes it as matched, which is the detail that decides how the part is used: an internally matched device carries its own input and output matching inside the package, so the board around it does not need a tuned network, and the price of that convenience is a narrower band.
The document link on the page points at the site root and serves nothing. That is not a rare event on this shelf, and it changes what a buyer can do. There is no breakdown voltage, no capacitance set, no thermal resistance and no fixture published for this row. Everything below is either the index row, the page text, or arithmetic that a buyer can repeat, and the arithmetic is labelled as arithmetic so nobody mistakes it for a vendor figure.
The absence of a document is itself a procurement fact. On a 500 W part the thermal resistance is the number that decides whether the product is buildable, and without it the heat sink can only be bounded. Two things follow: ask the vendor for the thermal resistance and the breakdown voltage in writing before the flange and the output network are specified, and measure the case temperature on the first build rather than assuming it.
The HXC50013 rows as the vendor publishes them
| Part class | LDMOS RF power transistor, internally matched, 500 W capable |
| Output, index row and page | 500 W |
| Output in dBm, calculated | 56.99 dBm |
| Frequency, index row | 433 MHz, single channel |
| Drain rail | 50 V nominal |
| Mode, page | CW and pulse |
| Gain, index row | 21 dB |
| Drain efficiency, index row | 74 per cent |
| Drive at 21 dB, calculated | 3.97 W, or 35.99 dBm |
| Load voltage at 500 W into 50 ohm, calculated | 158.1 V rms, 223.6 V peak |
| Peak against the 50 V rail, calculated | 4.47 times |
| Load voltage at a 2 to 1 mismatch, calculated | 447 V peak |
| Load voltage at a 3 to 1 mismatch, calculated | 671 V peak |
| DC input at 74 per cent efficiency, calculated | 676 W, 13.51 A at 50 V |
| Heat to remove at 74 per cent, calculated | 176 W |
| DC input at 65 per cent efficiency, calculated | 769 W, 15.38 A at 50 V |
| Heat to remove at 65 per cent, calculated | 269 W |
| Thermal resistance, junction to case | Not published for this row |
| Drain to source breakdown | Not published for this row |
| Capacitance set | Not published for this row |
| Test fixture and board material | Not published for this row |
| Package | Not published for this row, described only as matched |
| Applications listed on the page | ISM RF energy, RF heating at 433 MHz |
| Orderable addendum | None published |
| Packing quantity and moisture level | Not published |
What 500 W at 433 MHz asks of the rail, and what matching inside the package changes
500 W into 50 ohm is 158.1 V rms and 223.6 V peak, 4.47 times the 50 V rail. That ratio is normal for a matched push pull part at this power, and it tells the buyer where the voltage sits: the output combiner, the connector and the applicator feed all see 224 V at full power, 447 V at a 2 to 1 mismatch and 671 V at 3 to 1. In an ISM applicator the load is often worse than 3 to 1, because the load is the product being heated and its impedance changes as it heats.
Internal matching moves the problem rather than removing it. On an unmatched part the output network is on the board and can be tuned; on a matched part the network is inside the package and fixed, so the board is simple but the band is set by the vendor. At 433 MHz that is a good trade, because the ISM allocation is a narrow slice around 433.92 MHz and a single tuned network covers it with room to spare. It is a bad trade if the requirement is 400 to 470 MHz, where a matched part will be narrow and the buyer cannot widen it.
The current is 13.5 A at 74 per cent efficiency. That is a bus, not a trace, and at 433 MHz the current is concentrated in the conductor surface, so the bus has to be wide as well as thick. On a 500 W board the output stripline is usually the part of the board that decides the loss, and the 74 per cent efficiency on the row already includes the device only, not the board.
Thermal: what the missing figure costs
At 74 per cent efficiency the heat is 176 W and at 65 per cent it is 269 W. Without a published thermal resistance the junction cannot be computed, so bound it. On the same shelf a 1 kW part publishes 0.2 degrees per watt and a 70 W part publishes 0.7. A 500 W matched part normally lands between 0.25 and 0.35. At 0.3 degrees per watt and 176 W of heat the rise is 53 degrees, so at an 85 degree case the junction sits near 138 degrees against a 225 degree limit; at 269 W of heat the rise is 81 degrees and the junction sits near 166 degrees.
That range is comfortable, which is the good news. The bad news is that the bound is an assumption and the difference between 0.25 and 0.35 moves the junction by 18 degrees at this heat load. A buyer who needs the margin in writing asks the vendor for the figure before the heat sink is ordered, and a buyer who cannot get it measures the case at full power on the first build and works back from the assumption.
The 433 MHz band is helpful here. At a single narrow channel the output network loss is low and the heat is concentrated in the die, so the flange temperature tracks the heat load closely. On a broadband part the same power would spread more loss into the board and the flange reading would no longer represent the die.
Drive, gain and what 21 dB buys
21 dB of gain means the drive for 500 W is 3.97 W, which is a single small transistor stage. That is the highest gain per watt on the 50 V shelf at this power level, and it is the reason a 433 MHz ISM product can be built as two stages instead of three. The matched input is what makes the gain stable across the band, because the input match does not depend on the board.
The catch is that a matched part's gain is specified at a frequency and not across a band. The index gives 21 dB without a frequency, and the page gives no measured point at all. Plan the driver on 19 dB rather than 21 dB until a measurement exists, because a 2 dB error in gain at 500 W is a driver that cannot reach rated output and a fault that looks like a device problem.
The efficiency figure has the same status. 74 per cent is a good number for a 433 MHz LDMOS and it is plausible, but it is an index figure with no test condition attached. If the product runs at 65 per cent in reality the heat rises from 176 W to 269 W, which is the difference between a small heat sink and a large one. Ask for the condition behind the 74 per cent, or measure it on the first build.
Where the HXC50013 sits on the shelf
The 915 MHz group above it carries 700 W and 850 W on a 40 V rail, both matched, both with a page but no document. The 500 W single at 50 V to 500 MHz, the 650 W single at 50 V, and the 1 kW part at 50 V form the HF to VHF ladder. In decibels the step from 433 MHz 500 W to the 915 MHz 700 W is 1.46 dB, but the two parts sit on different rails and different bands, so the comparison is about the socket rather than the ladder.
Read as a choice, this row is the one for a 433 MHz ISM product at 500 W on 50 V where a matched device and a narrow band are both acceptable, and where the buyer is willing to obtain the thermal and breakdown figures directly from the vendor. A buyer who needs a document before committing takes the 1 kW part at 50 V, which publishes both a steady and a transient thermal figure; a buyer who needs 700 W at 915 MHz takes the 40 V row and changes the rail.
Before the purchase order goes out
Two procurement points. No document is reachable for this row, so the thermal resistance, the breakdown voltage and the fixture should be requested in writing, and the incoming route that handles a part arriving with no published document is on the incoming inspection plan page. Buyers comparing matched 433 MHz parts from several vendors should work from the RF power transistor cross reference, because a matched part has to be compared on band and package rather than on gain alone. The sourcing side of the same bill of materials is on the RF component sourcing page.