HXC50095
Product Specifications
HXC50095
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC50095 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC50095: 30 W on a 50 V rail and the 1.10 ratio that makes it a driver, not an output stage
The HXC50095 is a 30 W single ended LDMOS RF power transistor on a 50 V rail, filed on the HF to 1.5 GHz line and marked CW. The vendor page describes it as a 30 W highly rugged unmatched LDMOS FET for wideband commercial and industrial use from HF to 1.5 GHz. It is the smallest row on the 50 V side of this shelf and the one that most often ends up in front of a bigger device rather than at the antenna.
The arithmetic explains why. 30 W into 50 ohm is 38.7 V rms and 54.8 V peak, which is 1.10 times a 50 V rail. The drain barely has to swing above its supply, so the part runs far from breakdown, far from saturation and far from any thermal limit. A device that comfortable at rated power is not being used efficiently as an output stage on a 50 V bus: the same rail could drive 100 W or 140 W through the larger rows on the same shelf, and the buyer who chooses 30 W is buying margin, linearity or a driver level rather than maximum output.
No gain, no efficiency, no thermal resistance and no maximum ratings are published for this row. What follows is the published row, the arithmetic, and the two application patterns where 30 W on 50 V is the right answer rather than a compromise.
The HXC50095 rows as the vendor publishes them
| Part class | LDMOS RF power transistor, unmatched, single ended |
| Frequency range, index row | HF to 1.5 GHz |
| Frequency range, vendor page | HF to 1.5 GHz |
| Output, index row | 30 W |
| Output in dBm, calculated | 44.77 dBm |
| Drain rail, index row | 50 V |
| Mode, index row | CW |
| Load voltage at 30 W into 50 ohm, calculated | 38.7 V rms, 54.8 V peak |
| Peak against the 50 V rail, calculated | 1.10 times |
| Load voltage at a 2 to 1 mismatch, calculated | 110 V peak |
| Load voltage at a 3 to 1 mismatch, calculated | 164 V peak |
| DC input at 60 per cent efficiency, calculated | 50 W, 1.00 A at 50 V |
| Heat to remove at 60 per cent, calculated | 20 W |
| DC input at 55 per cent efficiency, calculated | 55 W, 1.09 A at 50 V |
| Heat to remove at 55 per cent, calculated | 25 W |
| DC input at 70 per cent efficiency, calculated | 43 W, 0.86 A at 50 V |
| Heat to remove at 70 per cent, calculated | 13 W |
| Gain | Not published |
| Efficiency | Not published |
| Thermal resistance, junction to case | Not published |
| Maximum ratings | Not published |
| Package | Not published on the row |
| Orderable addendum | None published |
| Moisture level and packing quantity | Not published |
The 1.10 ratio: what it buys and what it costs
A peak load voltage only 10 per cent above the rail means the device is operating well inside its voltage envelope. That has three practical consequences. The first is ruggedness: a part at 1.10 times its rail can survive a mismatch that would destroy a part running at 3.2 times the rail, because the reflected voltage has more room before it reaches breakdown. At 3 to 1 this row sees 164 V peak, which is an ordinary number for a flanged ceramic LDMOS part.
The second is linearity. A device backed off from its voltage limit has more headroom for a modulated envelope, so a 30 W part used at 10 W average with a 4 dB peak to average signal is running at a third of its rating and has a clean envelope. The same 30 W of average power taken from a part rated at 35 W would be at the edge of compression on every peak.
The third is efficiency. A part at 1.10 times its rail is not using its supply well: the DC input at 60 per cent efficiency is 50 W for 30 W of output, and the same 50 V bus could deliver 140 W through a larger row with a similar efficiency. That is the cost of the margin, and it is the reason this row belongs in a driver chain or in a low power output stage rather than in the final stage of a high power transmitter.
Where a 30 W row on a 50 V rail belongs
The first pattern is the driver. A 30 W stage with 15 to 20 dB of gain can deliver the 1 to 5 W that a 140 W or a 260 W row needs, with 8 to 15 dB of margin in hand, which means the driver is never the part that limits the system. On a 50 V bus the driver and the output stage share a rail, which removes a converter from the chain and removes its loss with it.
The second pattern is the output stage of a modest transmitter: a 20 to 30 W exciter for an industrial heater, a test source, or a low power broadcast translator. At 30 W the heat is 20 to 25 W, which a small sink moves without a fan, and the whole amplifier fits in a box the size of a book. That is a real product class and this row is sized for it.
The third pattern is the lab amplifier. A 30 W part on 50 V with a 1.10 ratio is a forgiving load for a student or a technician learning to tune a match: the part will not fail when the match is wrong, and the measurement can be repeated. Buyers who run training benches buy this class of device by the dozen for that reason.
Thermal at 30 W: 20 W of heat and a small sink
At 60 per cent efficiency the heat is 20 W and at 55 per cent it is 25 W. A 50 by 50 mm extruded sink with 20 mm fins moves that at a 30 degree rise by natural convection, and a 1 mm copper plate bolted to an aluminium chassis moves it at a 20 degree rise if the interface is good. At this power the thermal question is almost trivial, which is exactly why it gets skipped and why a part in a sealed box at 70 degrees internal ambient can still run hot.
With no published thermal resistance the junction has to be inferred. A planning figure of 2 degrees per watt, which is normal for a small flanged package at this power, gives 40 to 50 degrees of rise at 20 to 25 W and puts the junction at 125 to 135 degrees with an 85 degree case. That is comfortable against a 225 degree limit and it leaves room for a poor interface.
The one thermal rule that still applies is the interface. A dry joint between a flange and a sink at 25 W of heat costs 10 to 20 degrees, which is affordable here and would be fatal on a 260 W row. Torque the screws, use a thin film of compound, and check the flange flatness at goods inwards, because a warped flange is a thermal problem that no amount of compound fixes.
Gain and the driver budget
With no published gain, the planning range for a 50 V unmatched LDMOS at this power is 15 to 20 dB, which puts the drive for 30 W between 0.3 W and 0.95 W. That is a comfortable target for a small GaAs or a driver MMIC, and it is the reason this row pairs well with a 1 W driver and a 3 dB pad.
The pad matters more than the gain here. An unmatched input at 1.5 GHz presents an impedance that moves with frequency, and a driver that is not unconditionally stable can oscillate at a frequency where the match is worst, which is usually outside the intended band and therefore invisible on the intended measurement. A 3 dB pad costs a quarter of the drive margin and removes the problem.
The bias side is simple at this power. A quiescent current of 100 to 200 mA needs a gate voltage that varies by a few hundred millivolts between parts, so the bias network must be adjustable per device and must sequence the gate before the drain. A fixed divider that works on one part will put the next part into either cutoff or excessive quiescent current.
Choosing between this row and the ones above it
The nearest neighbour in power on the same 50 V rail and the same HF to 1.5 GHz band is the 60 W pair, which is 3.01 dB above this row with two devices and a combiner. Below it there is nothing on this shelf; the next step down in frequency coverage is the HF to 1 GHz singles at 80 W and above, which give more power but stop at 1 GHz.
So the decision is between a single device at 30 W with a 1.10 ratio and a pair at 60 W with a 1.55 ratio, and the answer depends on whether the system needs the last 3 dB. A transmitter specified at 25 W takes this row and runs it at 83 per cent of rating with a comfortable margin; a transmitter specified at 50 W takes the pair and gains 3 dB for one more device, one more bias and a combiner.
The full shelf, including the rows that cover 1.2 to 1.7 GHz and the L band parts above 1.5 GHz, is laid out with drive and heat at each rung on the RF power transistor cross reference page. The passives for a 30 W stage, where a 250 V output capacitor is adequate rather than marginal, are on the RF component sourcing page, and the goods inwards checks that catch a warped flange before it becomes a thermal complaint are on the incoming inspection plan page.