Contact Us

VBL17R10S

Brand: VBsemi
VBsemi VBL17R10S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBL17R10S — Discrete & Power Semiconductors | Superb Automation

VBL17R10S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBL17R10S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBL17R10S: a 700 V, 0.5 ohm N channel die for off line switching

The VBL17R10S is an N channel MOSFET printed at 700 V from drain to source with a plus or minus 30 V gate, in the D2PAK outline that the industry also calls TO-263. The summary gives 0.5 ohm at a 10 V gate with 5 A flowing, a continuous drain current of 10 A with the case at 25 C and 9 A with the case at 100 C, a pulsed rating of 30 A and a single pulse avalanche energy of 132 mJ. The junction is rated to 150 C, the drain source dV/dt is 50 V per nanosecond, and the vendor prints a low figure of merit, a low input capacitance of 680 pF and a gate charge of 38 nC typical as the three reasons to choose this die over a smaller one.

The 700 V class exists for the circuits that cannot use a 600 V part: a universal input supply that has to ride a 400 V bus plus a surge, a three phase 380 V rectified front end, or a lighting ballast with a high strike voltage. The 100 V of extra margin over a 600 V device is bought with a slightly higher resistance, and at 0.5 ohm this part is still a reasonable switch for a 50 W to 150 W converter.

The ratings a buyer checks first

Drain to source voltage700 V
Gate to source voltageplus or minus 30 V
On resistance at 10 V gate, 5 A0.5 ohm typical
Continuous drain current, case at 25 C and 100 C10 A and 9 A
Pulsed drain current30 A
Single pulse avalanche energy132 mJ
Maximum power dissipation, case at 25 C83 W
Junction to case and junction to ambient0.6 and 80 C per watt
Gate threshold at 250 microamp2 V minimum, 4 V maximum
Total gate charge at 560 V and 5 A38 nC typical, 56 nC maximum
Gate source and gate drain charge4 and 4.5 nC typical
Input, output and reverse transfer capacitance680, 140 and 5 pF
Effective output capacitance, energy and time related63 and 113 pF
Turn on delay and rise time13 and 11 ns typical
Turn off delay and fall time81 and 25 ns typical
Body diode forward drop at 5 A1.5 V maximum
Body diode reverse recovery time and charge270 ns and 3.3 microcoulomb typical
Peak reverse recovery current at 400 V30 A typical
Operating junction and storage rangeminus 55 to plus 150 C

Reading the electrical table instead of the front page

The figure of merit the vendor advertises is the product of resistance and gate charge, and the numbers give 0.5 ohm times 38 nC, which is 19 ohm nanocoulomb. That is a sound way to compare two high voltage dies on switching loss, but it says nothing about conduction loss, and in a 100 W flyback the conduction loss is usually the larger of the two. At 3 A the channel dissipates 4.5 W, and at 5 A it dissipates 12.5 W, which against a 0.6 C per watt junction to case is a 7.5 C rise on a well mounted tab and a 1000 C rise on a bare board. The 80 C per watt board figure means this part needs copper under the tab even at 2 A.

The capacitances are low across the board: 680 pF of input, 140 pF of output and only 5 pF of reverse transfer. The reverse transfer figure is what controls the Miller plateau and the susceptibility to a dV/dt induced turn on, and 5 pF is low enough that a 700 V drain edge will not switch the part on through the gate drain capacitance. The energy related output capacitance of 63 pF is the number for the turn on loss in a hard switched circuit, and it is modest for a 700 V die.

The gate charge split is worth reading. Four nanocoulomb of gate source charge against 4.5 nC of gate drain charge means almost the whole gate charge is the Miller charge, so the drive current has to be delivered during the plateau and the edge time is set by the driver rather than by the channel. A 0.5 A driver gives a 9 ns plateau at 4.5 nC and 10 V, which is consistent with the 11 ns rise the sheet prints. A weak controller pin that can only deliver 50 mA will stretch the plateau to 90 ns and the switching loss by a factor of eight.

The diode is slow at 270 ns of recovery and 3.3 microcoulomb recovered, and in a hard switched bridge that recovery is the loss that limits the switching frequency. In a flyback the diode does not conduct in reverse during normal operation, so the figure matters only for a fault, and the part is well suited to that topology. A buyer who plans a bridge should look at the diode figures before the resistance.

Where a 700 V D2PAK part earns its place

The first use is a flyback converter for a 90 W to 150 W adapter on a universal input, where the 700 V rating covers the reflected voltage plus the leakage spike with margin. The low reverse transfer capacitance keeps the drain edge clean and the 132 mJ avalanche rating absorbs the leakage energy when the clamp is slow.

The second use is a power factor correction boost stage running in discontinuous conduction mode at a lower power, where the peak current is 5 A and the switching frequency is high. The 38 nC gate charge and the 11 ns rise allow a 200 kHz switching frequency with a small inductor, and the 700 V rating covers the boost output at 400 V plus the surge.

The third use is a three phase 380 V rectified front end in an industrial supply, where the DC bus sits at 540 V and a 600 V part leaves no margin. The 700 V rating gives 160 V of headroom, which is what a 540 V bus needs for a switching overshoot and a line surge.

Sourcing notes and the second source question

At 700 V the second source question is decided by the diode and the capacitance, not by the resistance. A 600 V part of the same resistance is not a substitute on a 540 V bus, and a 700 V part with a much larger recovered charge will not work in a bridge at the same frequency. The power management cross reference keeps the recovery rows and both effective capacitance figures beside the resistance.

The gate rating of plus or minus 30 V is wider than the common 20 V and matters on a board where the gate loop rings. A replacement with a 20 V gate limit will fail on the same board even though the electrical table matches. The how to verify a drop in replacement page puts the gate rating in the first pass for that reason.

Where a product is moving from a 600 V part to a 700 V part because of field failures, the supplier quality audit page describes what we check on the avalanche and the dV/dt rating before a change is proposed, since a higher voltage part with a weaker avalanche rating can make the field failure worse.

Questions we answer before a reel is booked

The first question is the driver. At 56 nC maximum the gate needs about half an amp to keep the edge inside 20 ns, and a controller with a weak output will run the part hot on every cycle. This is the second most common cause of a 700 V switch failing on the bench, after the clamp.

The second question is the board area under the tab. At 80 C per watt from junction to ambient, a 5 W loss on a bare plane gives a 400 C rise, which is not workable. The part needs a copper pour of several square centimetres or a small sink, and we ask for the area before quoting a current.

The third question is the clamp voltage. The 132 mJ single pulse rating is measured with a specific inductance and a 25 C start, and a flyback that clamps at 650 V will push more energy into the die than one that clamps at 550 V. We ask for the clamp and the leakage inductance so the avalanche energy can be computed rather than assumed.