Contact Us

HXC50061

Brand: Hisiwell
Hisiwell HXC50061 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXC50061 — Discrete & Power Semiconductors | Superb Automation

HXC50061

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXC50061 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXC50061: a 15 W catalogue row with a 30 W document behind it

The HXC50061 is listed as a 15 W internally matched LDMOS device for cellular base station and ISM work from 700 to 2700 MHz, on a 28 V rail, in pulse. The product page repeats the 15 W figure. The document linked from the page is titled HX2270258E2 and describes a 30 W internally matched device for the same applications and the same band. That is not a naming difference, it is a factor of two in output, 3.01 dB, and it is the first thing a buyer has to settle.

There are two readings and only the vendor can choose between them. The first is that the catalogue row is a 15 W linear rating and the document describes the saturated capability of the same die, which is common on LDMOS parts sold into modulation schemes with a peak to average ratio. The second is that the document belongs to a different member of the family and was attached to the wrong page. The page does not pick a reading. It sets out both sets of numbers, labels which figure comes from which source, and states the gap in its first table row.

What the document does give is a real measurement across two bands, 1470 to 1530 MHz and 2500 to 2700 MHz, at a 28 V rail, 250 mA of quiescent current, a 10 microsecond pulse and a 12 per cent duty cycle. That is a modern cellular band split rather than a single point, and it is more informative than most documents on this shelf, which makes the wattage gap more frustrating rather than less.

The HXC50061 rows as the vendor publishes them

Part classLDMOS RF power transistor, internally matched, cellular and ISM
Output, index row and page15 W
Output, document description30 W
Output in dBm, calculated41.76 dBm at 15 W, 44.77 dBm at 30 W
Difference between the two readings, calculated3.01 dB
Frequency range, page700 to 2700 MHz
Frequency measured, document1470, 1500 and 1530 MHz, then 2500, 2600 and 2700 MHz
Drain rail and quiescent current, document28 V and 250 mA
Signal, documentPulse CW, 10 microsecond width, 12 per cent duty
Gain at 1 dB compression, 1470 to 1530 MHz18.7 to 19.3 dB
Gain at 1 dB compression, 2500 to 2700 MHz17.5 to 19.2 dB
Output at 1 dB compression, 1470 to 1530 MHz44.7 to 45.9 dBm, which is 29.5 to 38.9 W
Output at 1 dB compression, 2500 to 2700 MHz43.8 to 45.5 dBm, which is 24.0 to 35.5 W
Output at 3 dB compression, same bands44.8 to 46.5 dBm, which is 30.2 to 44.7 W
Drain efficiency at 1 dB compression, 1470 to 1530 MHz61.3 to 63.7 per cent
Drain efficiency at 1 dB compression, 2500 to 2700 MHz49.7 to 52.5 per cent
Input return loss, documentminus 10 dB typical
Drain to source breakdown, document65 V minimum
Gate to source maximum, documentminus 7 V to plus 10 V
Operating voltage maximum, document32 V
Junction and case temperature, document225 degrees junction, 150 degrees case
Thermal resistance, junction to case, documentTo be determined, no figure published
Gate threshold voltage, document2.05 V at 600 microamps, 28 V drain
Gate quiescent voltage, document2.8 V at 250 mA
Load mismatch, document10 to 1 at 30 W pulsed output at 1500 MHz, no degradation
ESD class, documentHuman body model Class 2
Document title against catalogue numberHX2270258E2 against HXC50061, not explained by the vendor
Orderable addendumNone published

What 15 W or 30 W on 28 V asks of the rail, and why the difference matters

15 W into 50 ohm is 27.4 V rms and 38.7 V peak, which is 1.38 times a 28 V rail; 30 W is 38.7 V rms and 54.8 V peak, which is 1.96 times the rail. Both ratios are modest, and the 65 V minimum breakdown gives room for either, so the rail is not the constraint at this power. The difference shows up in the drive and the heat rather than in the voltage.

At 19 dB of gain the drive for 15 W is 0.19 W, or 22.8 dBm, and for 30 W it is 0.38 W, or 25.8 dBm. A driver chosen for 0.19 W and installed behind a part that needs 0.38 W will not reach the higher output, and the symptom will be a stage that compresses early, which reads like a device fault. That is why the purchase decision has to settle the wattage before the driver is chosen.

The heat moves the same way. At 60 per cent efficiency, 15 W is 25 W of DC input, 0.89 A and 10 W of heat; 30 W is 50 W of DC input, 1.79 A and 20 W of heat. On a small matched package with no published thermal resistance, doubling the heat is the difference between a comfortable flange and one that needs a real heat sink, so the question is a mechanical one as much as an electrical one.

Thermal: a document that says to be determined

The thermal resistance row in the document reads to be determined. That is honest and it is also a gap: on a matched part the flange is the only thermal path, and without the figure the junction can only be bounded. Bounding it from the shelf, a 70 W unmatched part publishes 0.7 degrees per watt and a 10 W part 3, so a 30 W matched part normally sits near 1.0 to 1.5. At 1.2 degrees per watt and 20 W of heat the rise is 24 degrees, so at an 85 degree case the junction is near 109 degrees against a 225 degree limit.

The pulse condition helps further. The document measures at 12 per cent duty, so the average heat is a fraction of the instantaneous figure and the junction swing is small. A continuous product at the same output will run closer to the steady state calculation, and that is the case the missing figure has to cover.

Practically, ask the vendor for the thermal resistance before the flange is specified, and measure the case temperature at full power on the first build. On a small ceramic package with a 10 microsecond pulse, a thermocouple on the flange is a fair proxy for the case, and the number is stable enough to work from.

Drive, gain and the two bands the document measures

Gain runs 18.7 to 19.3 dB at 1470 to 1530 MHz and 17.5 to 19.2 dB at 2500 to 2700 MHz, so the part holds roughly 19 dB across both bands with a dip at 2.5 GHz where the input match has moved. That is good for a matched part and it means one driver can serve a dual band product without equalisation.

The efficiency is where the two bands separate. 61 to 64 per cent at L band against 50 to 53 per cent at 2.6 GHz is 10 points, which doubles the heat at the higher band for the same output. A product that covers both bands needs a heat sink sized on the 2.6 GHz case, not on the L band case, and the difference is 10 W against 20 W of heat at the same output.

The 10 to 1 mismatch test at 30 W pulsed output means the part survives a load that is fully mismatched, which is what a base station antenna under a fault looks like. It does not mean the output network survives it: at 3 to 1 the peak on the load reaches 164 V for 30 W, and the capacitors and the circulator have to be rated for that even when the die is not stressed.

Where the HXC50061 sits on the shelf

The 700 to 2700 MHz matched group has three rows: this 15 W catalogue part, the 30 W HXC50062 at 20 dB and 60 per cent, and the 100 W part at 1.8 to 2.7 GHz on 28 V. In decibels 15 W to 30 W is 3.01 dB and 30 W to 100 W is 5.23 dB, so the group is a ladder in 3 to 5 dB rungs with a wide top step.

Read as a choice, this row is the one for a low power cellular or ISM socket where a matched part at 19 dB removes the output network from the board, and where the buyer is willing to settle the 15 W against 30 W question with the vendor. A buyer who needs 30 W and a document that agrees with the catalogue takes the HXC50062; a buyer who needs 100 W at 2.6 GHz takes the 1.8 to 2.7 GHz row and accepts 11 dB of gain.

Before the purchase order goes out

Two procurement points. The document describes a 30 W part while the catalogue row says 15 W, so the purchase order has to name the figure and the vendor has to confirm which one the part is released against, and the incoming route for a document that disagrees with the label is on the incoming inspection plan page. Buyers lining this row up against competing 15 W and 30 W matched parts at 2.6 GHz should start from the RF power transistor cross reference, and a dual band bill of materials with the driver, the circulator and the passives on it can be placed through the one stop RF supply route.