Contact Us

HXC50153

Brand: Hisiwell
Hisiwell HXC50153 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXC50153 — Discrete & Power Semiconductors | Superb Automation

HXC50153

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXC50153 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXC50153: 10 W on 28 V, 23 dB of gain and a 3 degree per watt path

The HXC50153 is the small end of the HXC50 shelf: a 10 W, highly rugged, unmatched LDMOS device on a 28 V rail, filed for wideband commercial and industrial work up to 2 GHz, with 23 dB of gain and 63 per cent drain efficiency on the index row. It is the row a buyer takes when the requirement is a driver or a small final stage that has to work from HF to L band without a tuned output network, and when the budget is measured in milliwatts of drive rather than in watts.

The document attached to the page is titled HX210018. It describes a 10 W unmatched device for wideband commercial and industrial applications up to 2 GHz, which is the catalogue row in every respect except the name, and it adds the numbers the index does not carry: 28 V rail, 100 mA of quiescent current, and a single measured point at 960 MHz showing 23 dB of gain, 13 W at 1 dB compression and 63 per cent efficiency. The 13 W figure is a compression point in a soldered fixture, not a rating, and the 10 W in the catalogue is the row a system should be built against.

Three of the published figures are worth more than they look. The 3 degrees per watt thermal resistance is high for a power device and correct for a 10 W die, because the heat is only 5.9 W at 63 per cent efficiency and the rise from case to junction is 18 degrees. The 0.5 pF feedback capacitance is what makes 23 dB of gain possible at 960 MHz, since the internal feedback path is small enough that the input match is set by the external network. And the minus 10 dB input return loss is a measured figure rather than a claim, which tells the driver what load it will actually see.

The HXC50153 rows as the vendor publishes them

Part classLDMOS RF power transistor, unmatched, single ended, highly rugged
Output, index row and page10 W
Output in dBm, calculated40.00 dBm
Output at 1 dB compression, document13 W at 960 MHz in a soldered fixture
Frequency range, index rowHF to 2 GHz
Frequency measured, document960 MHz, single point
Drain rail28 V nominal, 40 V maximum operating
Quiescent current, document100 mA
Gain, index row and document23 dB typical at 960 MHz
Drain efficiency, index row and document63 per cent typical
Input return loss, documentminus 10 dB typical
Drain to source breakdown, document97 V typical, 90 V minimum at 1 mA
Gate to source maximum, documentminus 10 V to plus 10 V
Junction temperature maximum, document225 degrees C
Case operating temperature, document150 degrees C
Storage temperature, documentminus 65 to plus 150 degrees C
Thermal resistance, junction to case, document3 degrees C per watt, DC test at 85 degree case and 200 degree junction
Gate threshold voltage, document2.07 V at 50 microamps, 28 V drain
Gate quiescent voltage, document3.3 V at 100 mA, 28 V rail
Input capacitance, document16.2 pF at 28 V and 1 MHz
Output capacitance, document5.9 pF at 28 V and 1 MHz
Feedback capacitance, document0.5 pF at 28 V and 1 MHz
Leakage currents, document1 microamp drain at 75 V and at 28 V, 1 microamp gate
ESD class, documentHuman body model Class 2
Document title against catalogue numberHX210018 against HXC50153, not explained by the vendor
Orderable addendumNone published
Packing quantity and moisture levelNot published

What 10 W on 28 V asks of the load, and why the numbers look easy

10 W into 50 ohm is 22.4 V rms and 31.6 V peak, which is 1.13 times a 28 V rail. That ratio is the mark of a low power part on a high rail: the device never has to swing beyond its supply, so the 90 V breakdown never becomes the limit and the matching network can be built from small parts. On a 2 to 1 mismatch the peak reaches 63 V and at 3 to 1 it reaches 95 V, still inside the 90 V minimum breakdown only at 3 to 1 by a narrow margin, which is why even a 10 W socket deserves a mismatch check rather than a shrug.

Current is 0.57 A at 63 per cent efficiency, rising to 0.71 A at 50 per cent. A 10 W part that draws a little over half an amp is the kind of load a 12 V to 28 V boost converter can feed in a handheld product, and it is why this row appears in man portable and instrumentation equipment where the rail is generated rather than supplied.

The 13 W compression point in the document gives 1.14 dB of headroom over the 10 W rating. That headroom is useful in a modulation scheme with a peak to average ratio, because a signal that averages 10 W peaks well above it. Read the rating as the average the part can hold and the compression point as the ceiling the peaks touch, and the board does not have to be reworked when the modulation changes.

Thermal: 3 degrees per watt and why it is not a problem at this power

3 degrees per watt sounds poor next to the 0.2 degrees per watt of a 1 kW part, but the arithmetic is what matters. At 63 per cent efficiency the heat is 5.9 W, so the rise is 17.6 degrees and at an 85 degree case the junction sits near 103 degrees against a 225 degree limit. Even at 50 per cent efficiency, where the heat is 10 W, the rise is 30 degrees and the junction sits near 115 degrees.

What that means in practice is that a 10 W part can be mounted on a small flange with modest copper and still hold its junction far below the limit. The failure mode on this class of part is not the die, it is the bias network drifting with temperature, because the gate threshold at 2.07 V and the quiescent point at 3.3 V sit close to each other and a fixed divider does not track them. Use a bias loop that senses drain current rather than a resistor from the rail.

The case temperature is still worth measuring on the first build. On a small flange the thermocouple is measuring the flange and not the die, and the published 3 degrees per watt already includes the die to case path, so the reading is directly usable in the calculation without a second correction.

Drive, gain and the 2 GHz claim

23 dB of gain means the drive for 10 W is 50 mW, or 17 dBm. A 50 mW driver is a single transistor stage, which is what makes this row attractive as a final amplifier in low power radios and as a driver in front of the larger rows on the same shelf. The gain is high enough that the driver can be a wideband part with no tuning of its own.

The 2 GHz claim in the index has one measured point behind it at 960 MHz. An unmatched device that holds 23 dB at 960 MHz will not hold 23 dB at 2 GHz: the input impedance falls and the gain drops with frequency, and the 0.5 pF feedback capacitance that helps at L band becomes a larger fraction of the input admittance at S band. If the requirement is above 1.5 GHz, the sweep on your own fixture is the only honest input to the gain budget.

The 10 W row also has a second job on this shelf, which is to act as the driver for the 70 W and 150 W rows. A 10 W part with 23 dB of gain driven by 50 mW and feeding a 150 W part is a two stage chain with 38 dB of net gain, which is a comfortable budget for a single amplifier product and avoids a third stage.

Where the HXC50153 sits on the shelf

Near it on the 28 V line are a 30 W pair at 50 V with 23 dB and 63 per cent, a 20 W single at 12.5 V with 15 dB and 65 per cent, a 25 W single at 28 V with 20 dB, and a 40 W single at 28 V with 20 dB and 60 per cent. The step from 10 W to 20 W is 3.01 dB and from 20 W to 40 W is 3.01 dB, so the small end of the shelf is built in clean 3 dB rungs, which makes a requirement easy to place.

Read as a choice, this row is the one for a 10 W socket that needs high gain, a low drive and a rugged die, and that can accept a vendor document filed under another name. A buyer who needs 20 W takes the 12.5 V single and gives up rail headroom; a buyer who needs to stay on 28 V takes the 40 W single and accepts 20 dB instead of 23 dB.

Before the purchase order goes out

Procurement follows the same pattern as the rest of this shelf. No orderable addendum is published, so the reel or tray quantity, the moisture level and the marking have to be confirmed in writing, and the route for a document that carries a different name from the catalogue number is on the incoming inspection plan page. Buyers who need to place this row against a competitor's 10 W LDMOS should start from the RF power transistor cross reference and compare rail, gain and package rather than wattage alone, while the sourcing side of a mixed RF bill of materials is covered on the RF component sourcing page.